Click on Series name for product info on aimtec.com Series AM10EW-NZ 10 Watt | DC-DC Converter FEATURES: • Efficiency up to 87% • Input Under-voltage Protection • Ultra-Wide 4:1 input range • Over Voltage, Over Current Protection ● I/O Isolation 1500, 2250 & 3000VDC • Continuous Short Circuit Protection o o • No-load power consumption ≤0.12W • Operating temperature -40 C to + 85 C • On/Off remote control Models Single output Input Voltage Output Output I/O Isolation Capacitive load Efficiency Model (V) Voltage Current max (VDC) max (μF) (%) (V) (mA) AM10EW-2403SH30-NZ 9-36 3.3 2400 3000 5400 79 AM10EW-2405SH30-NZ 9-36 5 2000 3000 5400 82 AM10EW-2409SH30-NZ 9-36 9 1111 3000 680 85 AM10EW-2412SH30-NZ 9-36 12 833 3000 470 86 AM10EW-2415SH30-NZ 9-36 15 667 3000 330 87 AM10EW-2424SH30-NZ 9-36 24 416 3000 100 87 AM10EW-4803SH30-NZ 18-75 3.3 2400 3000 5400 79 AM10EW-4805SH30-NZ 18-75 5 2000 3000 5400 82 AM10EW-4812SH30-NZ 18-75 12 833 3000 470 86 AM10EW-4815SH30-NZ 18-75 15 667 3000 330 87 AM10EW-4824SH30-NZ 18-75 24 416 3000 100 87 AM10EW-11005S-NZ 40~160 5 2000 1500 2200 81 AM10EW-11012S-NZ 40~160 12 833 1500 220 85 AM10EW-11015S-NZ 40~160 15 667 1500 100 85 AM10EW-11024S-NZ 40~160 24 416 1500 47 86 AM10EW-11003SH22-NZ 40~160 3.3 2400 2250 5400 76 AM10EW-11005SH22-NZ 40~160 5 2000 2250 5400 80 AM10EW-11012SH22-NZ 40~160 12 833 2250 470 84 AM10EW-11015SH22-NZ 40~160 15 667 2250 330 84 AM10EW-11024SH22-NZ 40~160 24 417 2250 100 85 Add suffix “-K” for optional heat sink *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate. **Add suffix “-K” for optional heatsink, “-K-ST” for optional heatsink and screw terminal bottom plate or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate. Models Dual output Input Output Output I/O Isolation Capacitive load Efficiency Model Voltage (V) Voltage Current max (VDC) max (μF) (%) (V) (mA) AM10EW-2405DH30-NZ 9-36 ±5 ±1000 3000 ±1000 82 AM10EW-2412DH30-NZ 9-36 ±12 ±416 3000 ±330 86 AM10EW-2415DH30-NZ 9-36 ±15 ±333 3000 ±220 87 AM10EW-4805DH30-NZ 18-75 ±5 ±1000 3000 ±1000 82 AM10EW-4812DH30-NZ 18-75 ±12 ±416 3000 ±330 86 AM10EW-4815DH30-NZ 18-75 ±15 ±333 3000 ±220 87 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 24 9-36 Voltage range 48 18-75 VDC 110 40~160 www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 1 of 9 North America only Series AM10EW-NZ 10 Watt | DC-DC Converter 24 521 Input Current (full load) 48 261 mA 110 117 Filter  (Pi) Network 24  50 Input Surge Voltage (1sec max.) 48 100 VDC 110 180 Start-up time Nominal Input, resistive load 10 ms 24 40 Reflected Input Ripple Current 48 30 mA 110 30 24 6.5 Under-voltage lockout 48 15.5 V 110 (2250 Isolated models) 33 On 3.5-12VDC or leave open Remote On/Off Control (24 & 48Vin) Off 0-1.2VDC or connect to GND, idle current 5-6mA Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 1 min, <1mA 1500, 2250 & 3000 VDC Tested I/FG & O/FG 1 min, <1Ma, 2250VDC I/O isolated models 1600 VDC Resistance At 500VDC Isolation > 1000 MOhm 24 & 48 Vin, I/O, 100KHz/0.1V 500 Capacitance 110 Vin (1500VDC isolation), I/O, 100KHz/0.1V 1000 pF 110 Vin (2250VDC isolation), I/O, 100KHz/0.1V 2200 Output Specifications Parameters Conditions Typical Maximum Units 110 Vin (2250VDC isolation), 0-100% load Voltage accuracy ±1 ±3 % Others, 5-100% load Voltage balance (Dual Output Models) Balanced Load ±1 ±2 % 110 Vin (2250VDC isolation), Full Load (HL-LL) ±0.2 ±0.5 Line voltage regulation % Others, Full Load (HL-LL) ±0.5 ±1 110 Vin (2250VDC isolation), 0-100% load ±0.5 ±1 Load voltage regulation % Others, 5-100% load ±0.5 ±1.5 50% load on one output & 10-100% load on second Cross Regulation ±5 % load Short Circuit protection Continuous Short Circuit restart Auto Recovery Over Voltage Protection 120 160 % of Vo 24 & 48 Vin models 140 190 Over Current Protection % of Io 110 Vin (2250VDC isolation) 120 210 110 Vin (2250VDC isolation), 25% Load Step Change 300 500 Transient Recovery Time µs Others, 25% Load Step Change 500 1000 Transient Response Deviation 25% Load Step Change ±3 ±8 % o Temperature coefficient ±0.03 %/ C Ripple & Noise 20Mhz bandwidth 60 120 mV p-p General Specifications Parameters Conditions Typical Maximum Units 110 Vin (2250VDC isolation), 100% load 300 Switching frequency KHz Others, 100% load 350 o Operating temperature Derating above 71°C -40 to +85 C o Storage temperature -55 to +125 C o Max case temperature 105 C Cooling Free air convection Humidity Non-condensing 95 % o Solder Temp Leads 1.5 mm from case 10 sec. 300 C Plastic (3000VDC Isolated models) Case material Aluminum Alloy (Others) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 2 of 9 North America only Series AM10EW-NZ 10 Watt | DC-DC Converter 24 (3000VDC Isolated models) Pin mountable without heatsink 22 (1500VDC Isolated models) 26 (2250VDC Isolated models) 30 (1500VDC Isolated models) Pin mountable with heatsink 34 (2250VDC Isolated models) 46 (3000VDC Isolated models) -ST option without heatsink 44 (1500VDC Isolated models) Weight 48 (2250VDC Isolated models) g 52 (1500VDC Isolated models) -ST option with heatsink 56 (2250VDC Isolated models) 66 (3000VDC Isolated models) -STD option without heatsink 64 (1500VDC Isolated models) 68 (2250VDC Isolated models) 72 (1500VDC Isolated models) -STD option with heatsink 76 (2250VDC Isolated models) 3000VDC Isolated models 2.03 x 1.04 x 0.47 inches; 51.50 x 26.50 x 12.00mm Dimensions (L x W x H) Others 2.00 x 1.00 x 0.46 inches; 50.80 x 25.40 x 11.80mm Optional packages See dimensions drawing o MTBF >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) Environmental Specifications Parameters Test mode 10-55Hz Vibration (24 & 48 Vin) Acceleration 10G, 30min one cycle, every axis tested Test mode 5-150Hz Vibration (110 Vin/1500VDC isolation) Acceleration 2G, 30min one cycle, every axis tested Displacement 7.5mm Vibration (110 Vin/2250VDC isolation) IEC61373 car body 1 B mold Safety Specifications Parameters Approvals CE, UL (3000VDC Isolated models – dual and 24V input single output models) EN/IEC/UL60950-1 EN 55022, class A (all models) and EMI EN50121-3-2 class A (2250 VDC Isolated models) IEC61000-4-2, Contact ±6KV (110Vin), Contact ±4KV (24 & 48 Vin), Criteria B IEC61000-4-3, 10V/m, Criteria A IEC61000-4-4, ±4KV (110Vin), ±2KV (24 & 48 Vin with the recommended EMC circuit), Criteria B Standards IEC61000-4-5, ±2KV, Criteria B, (with the recommended EMC circuit) IEC61000-4-6, 3 Vrms, 10 Vrms (2250 VDC Isolated models) Criteria A IEC61000-4-29, 0-70%, Criteria B IEC/EN/UL 60950-1 Meets EN50155 (2250 VDC Isolated models) Free Air Convection Derating º C without heatsink 71 100 º 75 C with heatsink 80 60 Safe Operating Area 40 20 0 71 75 85 80 100 - 40 - 20 0 20 40 60 º C Ambient Temperature www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 3 of 9 North America only Output Power (%) Series AM10EW-NZ 10 Watt | DC-DC Converter Pin Out Specifications Dimensions 3000VDC Isolated models 3000VDC Isolated models 51.50 (2.03) Pin Single 6 1 On/Off Control 2 -Vin 3 3 +Vin 5 Bottom View 4 - Vout 2 5 No pin 6 + Vout 1 4 15.24 20.32 15.24 (0.60) (0.80) (0.60) Pin Dual 1 On/Off Control Notes: 2 -Vin All dimensions are typical in millimeters (inches). 3 +Vin Pin diameter Tolerance ±0.10 (±0.004) 4 - Vout Case Tolerance ±0.50 (±0.02) DIA 5 Common 1.00 6 + Vout (0.04) Pin Out Specifications Dimensions of Other models Other models 50.80 20.32 (2.00) (0.80) Pin Single 1 Vin - 3 2 Vin + 3 +Vout 2 Bottom View 4 -Vout 1 4 50.8 (2.00) Built-in Stand-offs to ease PCB cleaning Notes: All dimensions are typical in millimeters (inches). Tolerance ±0.25 (±0.01) DIA 1.00 (0.04) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 4 of 9 North America only 25.40 12.00 26.50 (1.00) (0.47) (1.04) 11.80 (0.47) 4.10 5.08 7.62 10.16 (0.16) (0.20) 5.08 (0.30) (0.40) (0.20) 20.32 (0.80) 10.16 10.16 25.4 (0.40) (0.40) (1.00) 2.54 2.54 (0.10) (0.10) Series AM10EW-NZ 10 Watt | DC-DC Converter Dimensions of the preinstalled heatsink option Side view DIA 1.00 (0.04) 6 3 5 Bottom View 2 1 4 15.54 20.32 15.54 (0.61) (0.80) (0.61) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) Dimensions with -ST options Pin Out Specifications 76.00 (2.99) Pin Single 61.60 1 N.C. (2.43) LED light 2 -Vin 3 +Vin 4 + Vout 1 6 5 N.C. Top view 6 - Vout 2 5 3 4 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Side view 3000VDC Isolated models Pin Single 1 On/Off Control 2 -Vin 3 +Vin 4 - Vout 5 No pin 6 + Vout www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 5 of 9 North America only 31.50 7.62 10.56 (1.24) 5.08 (0.30) (0.42) 16.50 (0.20) (0.65) 10.16 10.16 (0.40) (0.40) 2.94 2.94 4.10 (0.12) (0.12) (0.16) 8.80 (0.35) 21.20 (0.84) 23.00 (0.91) Series AM10EW-NZ 10 Watt | DC-DC Converter Dimensions with -STD options Pin Out Specifications 76.00 (2.99) 61.60 Pin Single (2.43) 1 N.C. 2 -Vin LED light 3 +Vin 4 + Vout 5 N.C. 1 6 6 - Vout Top view 5 2 3 4 3000VDC Isolated models Pin Single Ø3.30 1 On/Off Control Ø0.13 2 -Vin 3 +Vin 4 - Vout Side view 5 No pin 6 + Vout Dimensions: mm (inch) Case Tolerance:± 1.00 (0.04) Wire gauge: 24-12AWG Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) Pin Single 61.60 1 N.C. (2.43) 2 -Vin LED light 3 +Vin 4 + Vout 5 N.C. 1 6 6 - Vout Top view 5 2 3 4 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) 3000VDC Isolated models Wire gauge: 24-12AWG Pin Single 1 On/Off Control 2 -Vin Side view 3 +Vin 4 - Vout 5 No pin 6 + Vout www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 6 of 9 North America only 31.50 31.50 25.30 (1.24) (1.24) (1.00) 8.80 (0.35) 21.20 9.80 (0.84) 23.00 (0.39) (0.91) 23.00 25.80 (0.91) (1.02) Series AM10EW-NZ 10 Watt | DC-DC Converter Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 Pin Single (2.43) 1 N.C. 2 -Vin LED light 3 +Vin 4 + Vout 5 N.C. 1 6 6 - Vout Top view 5 2 3 4 Ø3.30 Ø0.13 3000VDC Isolated models Pin Single Side view 1 On/Off Control 2 -Vin 3 +Vin 4 - Vout 5 No pin 6 + Vout Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG EMC recommended filter 110Vin models CY1 1nF/2KV LCM F1 R1 +Vo 22mH +Vin C3 C1 C2 D1 MOV DC-DC Converter -Vo -Vin CY2 1nF/2KV MOV C1 & C2 R1 C3 D1 S20K130 1 µF / 200V 1 Ω 100 µF / 200V ER304 www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 7 of 9 North America only 31.50 (1.24) 29.90 (1.18) 9.80 (0.39) 23.00 25.80 (0.91) (1.02) Series AM10EW-NZ 10 Watt | DC-DC Converter EMC recommended filter 3000VDC Isolated models CY1 1nF/3KV 24Vin single output models LDM F1 4.7µH +Vin +Vo C4 C1 C2 MOV DC-DC Converter -Vin -Vo CY1 1nF/3KV MOV C1 C2 C4 CY1 & CY2 LDM S20K30 330 µF / 50V 1 µF / 50V 10 µF / 50V 1 nF / 3KV 4.7 µH CY1 48Vin single output models 1nF/3KV LCM F1 6.8mH +Vin +Vo C4 C1 C2 C3 MOV DC-DC Converter -Vin -Vo MOV C1 C2 & C3 C4 CY1 S20K60 330 µF / 100V 1 µF / 100V 10 µF / 50V 1nF/3KV CY1 3000VDC Isolated dual output models 1nF/3KV LCM +Vo F1 4.7mH +Vin C4 Com C1 C2 C3 MOV DC-DC Converter C5 -Vin -Vo CY1 1nF/3KV Vin MOV C1 C2 & C3 C4 & C5 24V S20K30 330 µF / 50V 1 µF / 50V 10 µF / 50V 28V S20K60 330 µF / 100V 1 µF / 100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 8 of 9 North America only Series AM10EW-NZ 10 Watt | DC-DC Converter by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.H 9 of 9 North America only