Series AM10WM-NZ 10 Watt | DC-DC Converter FEATURES:  Super wide Input range 200-1500VDC  No minimum load required  Operating temperature of -25 to +70°C  High efficiency of up to 70%  Input under voltage lockout  I/O Isolation of 4000VAC  Over current and Over Voltage protection  Reversed connection protection Models Single output Output Output Max Input Voltage Isolation Efficiency Model Voltage Current max Capacitive (V) (VAC) (800VDC) (%) (V) (A) Load(uF) AM10WM-80005S-NZ 200-1500 5 2 4000 6000 70 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units Voltage range 800VDC 200-1500 VDC 200VDC input 130 Input current 800VDC input 30 mA 1500VDC input 25 200VDC input 50 Inrush current <2ms 800VDC input 80 A 1500VDC input 150 External fuse Slow blow, 15A/1500VDC Lockout ON 170-185 Input under voltage protection VDC Lockout OFF 180-195 Startup time* Full load 2 s *The cooling time between input under voltage ON and OFF is over 15s. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 1 min 4000 VAC Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±2 % Line voltage regulation LL-HL, full load ±1 % of Vin Load voltage regulation 0-100% load ±1 % Over voltage protection Zener diode clamp Over current protection Auto recovery ≥120 % of Iout Short Circuit protection Continuous Short circuit restart Auto recovery o Temperature coefficient ±0.02 %/ C Ripple & Noise 20MHz Bandwidth 150 300 mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 65 kHz Operating temperature With derating -25 to 70 °C Storage temperature -25 to 85 °C Maximum case temperature 95 °C Cooling Natural convection Humidity 95 % RH www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R16 1 of 4 North America only Series AM10WM-NZ 10 Watt | DC-DC Converter Case material Heat resistant, black plastic (UL94-V0) Weight 270 g Dimensions (L x W x H) 4.29 x 2.30 x 1.18 inches 109.00 x 58.50 x 30.00 mm o MTBF >300,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) o Maximum soldering temperature 1.5mm from case for 3-5 sec 360 C Safety Specifications Parameters EN55022, class A (with the recommended EMC circuit) EMI - Conducted and radiated emission EN55024: 2010 Electrostatic Discharge Immunity IEC 61000-4-2: Contact ±6KV/Air ±8KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3: 10V/m, Criteria A Standards Electrical Fast Transient/Burst Immunity IEC 61000-4-4: ±2KV, Criteria B (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5: ±1KV, Criteria B (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6: 10Vrms, Criteria A Pin Out Specifications Pin Single 1 +Vin 2 -Vin 3 & 4 N.C. 5 -Vout 6 +Vout N.C. Not connected Dimensions 109.00 (4.29) 97.30 (3.83) 4 3 1 Ø1.20 TOP VIEW 5 (0.05) 2 58.50 46.30 BOTTOM 6 (1.82) (2.30) 6 2 Ø 2.3 (Ø 0.09) VIEW 5 1 3 Ø 2.3 (Ø 0.09) 4 Ø1.80 (0.07) Ø 2.3 (Ø 0.09) 4xM3 Ø 1.7 (Ø 0.07) 3.00(0.12) 96.32 Ø 2.3 (Ø 0.09) (3.79) Ø 1.7 (Ø 0.07) 30.00 DIV: 5.08 (0.2) Ø 3.5 (Ø 0.14)) (1.18) ᴓ4.50(0.18) Dimensions: mm (inch) Case Tolerance: ±0.50 (0.02) Pin Tolerance: ± 1.50 (0.06) 4xM3 3.00(0.12) Pin diameter Tolerance: ±0.10 (0.004) Pin 1, 2, 5 & 6 diameter: 1.80 (0.07) Pin 3 & 4 diameter: 1.20 (0.047) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R16 2 of 4 North America only 19.05 10.16 (0.40) (0.75) 15.60 6.00 (0.61) (0.24) 30.70 (1.21) 8.90 (0.35) 5.08 (0.20) 6.00 (0.24) 4.50 (1.18) Series AM10WM-NZ 10 Watt | DC-DC Converter Derating Altitude Derating curve Free Air Convection 100 100 80 80 Safe Operating Area 200-1500VDC 60 60 40 40 20 20 0 0 50 70 80 100 0 2000 5000 - 25 -10 0 20 40 60 º C Altitude (m ) Ambient Temperature *NOTE: Derating is indicated at natural convection. Sufficient air space around is needed. Efficiency curve Typical Application circuit * Single Output FUSE 15A/1500V 6 + Vout +Vin 1 + DC DC C1 C2 TVS 1µF/50V 120µF/35V -Vin 2 5 - Vout Note: TVS 7V www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R16 3 of 4 North America only Output Power (%) Output Power (%) Series AM10WM-NZ 10 Watt | DC-DC Converter Recommended EMC Circuit LDM Single Output FUSE LCM 330µH/1A 15A/1500VDC 7mH/1A + Vout + Vout + Vin + Vin + C7 C1 R1 + C8 C2 R2 TVS + C6 + DC DC C9 C3 R3 C5 + 1µF/50V C10 C4 R4 - Vin - Vin - Vout - Vout C1, C2, C3 & C4 C7, C8, C9 & C10 R1, R2, R3 & R4 C6 TVS 47 µF/450V 100 nF/275V 1MΩ / 2W 120 µF / 35V 7V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R16 4 of 4 North America only