Click on Series name for product info on aimtec.com Series AM15CW-Z 15Watt | DC-DC Converter FEATURES: • Ultra-compact footprint 1”x1” • Adjustable Output Voltage • Ultra-wide Input Range 4:1 • Operating Temperature -40ºC to +85ºC • 1600 VDC Isolation • Over Current and Over Voltage Protection • Remote ON/OFF Function • Efficiency up to 89% • No Minimum Load Required • RoHS Compliant Models Single output Output Max Input Voltage Output Current Isolation Efficiency Model Voltage Capacitive (V) max (A) (VDC) (%) (V) Load (uF) AM15CW-2403SZ 9-36 3.3 4 1600 1000 86 AM15CW-2405SZ 9-36 5 3 1600 1000 87 AM15CW-2412SZ 9-36 12 1.3 1600 330 88 AM15CW-2415SZ 9-36 15 1 1600 220 89 AM15CW-4803SZ 18-75 3.3 4 1600 1000 84 AM15CW-4805SZ 18-75 5 3 1600 1000 86 AM15CW-4812SZ 18-75 12 1.3 1600 330 87 AM15CW-4815SZ 18-75 15 1 1600 220 88 Models Dual output Output Max Input Voltage Output Current Isolation Efficiency Model Voltage Capacitive (V) max (A) (VDC) (%) (V) Load (uF) AM15CW-2405DZ 9-36 ±5 ±1.5 1600 ±470 85 AM15CW-2412DZ 9-36 ±12 ±0.625 1600 ±220 88 AM15CW-2415DZ 9-36 ±15 ±0.5 1600 ±100 89 AM15CW-4805DZ 18-75 ±5 ±1.5 1600 ±470 84 AM15CW-4812DZ 18-75 ±12 ±0.625 1600 ±220 87 AM15CW-4815DZ 18-75 ±15 ±0.5 1600 ±100 88 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 24 9-36 Voltage range VDC 48 18-75 Filter π Start up time Nominal Vin with constant resistive 20 ms load 24 Vin 50 Absolute Maximum Rating VDC 48 Vin 100 Peak Input Voltage time 100 ms On/Off control ON –3 to 12VDC (or open) ; OFF – 0 to 1.2VDC or short pin 2 to pin 3; OFF idle current – 5mA No load current 15 mA 24 Vin ON/OFF 8.5 /7 Under voltage lockout VDC 48Vin ON/OFF 17/15 Input reflected ripple current 20 mA p-p www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.G 1 of 4 North America only Series AM15CW-Z 15Watt | DC-DC Converter Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 3 sec 1600 VDC Case to Input 3 sec 1600 VDC Case to Output 3 sec 1600 VDC Resistance >1000 MOhm Capacitance 1200 pF Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±1 % 25% load on one output - 100% load Cross Regulation (Dual Output Models) ±5 % on second load Over voltage protection Zener Diode Clamp 120 % Over current protection Full Load 170 % Short Circuit protection Continuous Short circuit restart Auto-Recovery Line voltage regulation (Single) HL-LL ±0.2 % Line voltage regulation (Dual) HL-LL, balanced load ±0.5 % Load voltage regulation (Single) 0% to 100% load ±0.5 % Load voltage regulation (Dual) 0% to 100% balanced load ±1 % o Temperature coefficient ±0.02 %/ C Ripple & Noise 20MHz Bandwidth 100 mV p-p Voltage adjustment range Trim - Single output models only 10 % General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 375 KHz o Operating temperature With derating above +55°C -40 to +85 C o Storage temperature -40 to +125 C o Maximum case temperature 100 C o Derating 2.6 %/ C Cooling Free air convection Humidity 95 % RH Case material Nickel-coated copper Weight 18 g Dimensions (L x W x H) 1.00 x 1.00 x 0.40 inches 25.40 x 25.40 x 10.16 mm o MTBF > 560,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) o Maximum soldering temperature 1.5mm from case for 10 sec 260 C Transient recovery time Load step change 75% to 50% to 25% 250 µS Transient recovery deviation Load step change 75% to 50% to 25% ±3 % Safety Specifications Parameters Agency Approvals CE, UL UL 60950-1, UL62368-1 EN 55022 Class A EN 61000-4-2 Perf. Criteria A EN 61000-4-3 Perf. Criteria A Standards EN 61000-4-4 Perf. Criteria A (external 220uF/100V cap required) EN 61000-4-5 Perf. Criteria A (external 220uF/100V cap required) EN 61000-4-6 Perf. Criteria A EN 61000-4-8 Perf. Criteria A www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.G 2 of 4 North America only Series AM15CW-Z 15Watt | DC-DC Converter Pin Out Specifications Single Dual Pin 1 + V input + V input 2 - V input - V input 3 On/Off Control On/Off Control 4 + V output + V output 5 Trim Common 6 - V output - V output Dimensions Bottom View Top View 2.54 10.16 10.16 (0.10) 25.40 (0.40) (0.40) (1.00) 5 6 4 +V Output Trim -V Output +V -V Input Input CTRL 1 2 3 7.62 10.16 5.08 (0.30) (0.40) (0.20) Side View Printed Face 2.54 1.00 (0.10) (0.39) Derating Trimming Free Air Convection º 55 C 100 80 Safe Operating Area 60 40 20 0 85 80 100 - 40 - 20 0 20 40 60 º C Ambient Temperature www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.G 3 of 4 North America only Output Power (%) 25.40 9.90 (1.00) (0.39) 20.32 2.54 2.54 (0.10) (0.80) (0.10) Series AM15CW-Z 15Watt | DC-DC Converter Test Circuits Note: 1. Input filter (C1, C2, L) are needed to meet conducted emission (EN 55022 Class A) and should be mounted as close as possible to the converter. L 12uH +V input +V output + DC/DC Load - C2 C1 Converter 2.2uF/100V 2.2uF/100V -V output - V input Recommended circuit for class B compliance +V output L +V input C1 C2 DC/DC Converter Load -V input -V output C3 C1 & C2 C3 L 2.2µF / 100V 1nF / 3KV 12µH NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.G 4 of 4 North America only