AIMTEC AM2GW-4805D-NZ

Click on Series name for product info on aimtec.com Series AM2GW-NZ 2 Watt | DC-DC Converter FEATURES: o o • RoHS compliant • Operating temperature -40 C to + 85 C • Ultra wide 4:1 input range • Continuous Short circuit protection • Remote On/Off Control • High efficiency up to 76% • 9 pin SIP package • Low ripple and noise Models Single output Output Output Current Max Capacitive Input Isolation Efficiency Model Voltage max Load Voltage (V) (VDC) (V) (mA) (μF) AM2GW-2405S-NZ 9-36 5 400 1500 820 75 AM2GW-4805S-NZ 18-72 5 400 1500 820 76 Input Specifications Parameters Nominal Typical Maximum Units 24 9-36 Voltage range VDC 48 18-72 Filter Capacitor 24 Vin 40 Maximum Rating VDC 48 Vin 80 Peak Input Voltage time 100 ms On/Off Control ON – low or open; OFF – high On/Off input current 5 10 mA * Exceeding the maximum permissible value of 20mA for the Input On/Off current will damage the converter. Isolation Specifications Parameters Conditions Typical Rated Units TestedI/O voltage 60 sec 1500 VDC Resistance At 500VDC > 1000 MOhm Capacitance 80 pF Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±3 % Short Circuit protection Continuous Short Circuit restart Auto recovery Line voltage regulation LL~HL ±0.75 % Load voltage regulation Load 10~100% ±1.5 % o Temperature coefficient ±0.03 %/ C Ripple & Noise At 20MHz Bandwidth 100 mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load, Vin nominal >100 550 KHz o o Operating temperature With derating above 71 C -40 to +85 C o Storage temperature -50 to +125 C o Temperature rise Full load 15 35 C Cooling Free air convection Humidity 95 % Case material Non-conductive black plastic (UL94V-0 rated) Weight 7 g Dimensions (L x W x H) 1.02 x 0.37x 0.49 inch26.00 x 9.60 x 12.00 mm o MTBF >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) NOTE: All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R6.F 1 of 2 North America only Series AM2GW-NZ 2 Watt | DC-DC Converter Pin Out Specifications Dimensions 26.00 (1.02) 9.60 Pin Single (0.37) PRINTED FACE 1 - V Input 2 + V Input 12.50 3 On/Off Control (0.49) 6 + V Output 7 N.C. 8 N.C. 0.50 (0.02) 4.00 9 - V Output (0.16) 2.54 (0.10) 0.50 (0.02) Derating Free Air Convection 0.300 9.60 (0.012) (0.37) 1 2 3 6 7 8 9 2.90 º 71 C (0.11) 2.000 100 (0.079) 0.50 (0.02) 80 Safe Operating Area 60 40 20 0 85 - 40 - 20 0 20 40 60 80 100 Ambient Temperature º C Control ON/OFF pin connection example: 1K 1N4148 MCU CONVERTER Vcc-5V PIN 3 The voltage could be applied through a limiting resistor and a switching diode. The converter is in a low power mode during high level phase. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R6.F 2 of 2 North America only Output Power (%)