AIMTEC AM2L-0509D-NZ

Click on Series name for product info on aimtec.com Series AM2L-NZ 2 Watt | DC-DC Converter FEATURES: • Low Profile SMD • MTBF>1,000,000 hours • 1000VDC & 6000VDC Isolation • Operating temperature: -40°C to +85°C • Industry Standard Pinout • High Efficiency up to 85% • Unregulated Single & Dual Outputs Models Single output Output Voltage Output Current Isolation Efficiency Model Input Voltage(V) (V) max(mA) (VDC) (%) AM2L-0505SH60-NZ 4.5-5.5 5 400 6000 77 AM2L-1205SH60-NZ 10.8-13.2 5 400 6000 78 AM2L-1215SH60-NZ 10.8-13.2 15 133 6000 81 AM2L-2405SH60-NZ 21.6-26.4 5 400 6000 79 AM2L-2415SH60-NZ 21.6-26.4 15 133 6000 80 Models Dual output Input Voltage Output Voltage Output Current Isolation Efficiency Model (V) (V) max (mA) (VDC) (%) AM2L-0505D-NZ 4.5-5.5 ±5 ±200 1000 82 AM2L-0512D-NZ 4.5-5.5 ±12 ±83 1000 84 AM2L-1215D-NZ 10.8-13.2 ±15 ±67 1000 85 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 5 4.5-5.5 Voltage range 12 10.8-13.2 VDC 24 21.6-26.4 Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1000, 6000 VDC Capacitance 500VDC 10 pF Resistance 500Vdc >1000 MOhm Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy See Tolerance Graph ±5 % 1000VDC Momentary 1 sec Short Circuit protection 6000VDC Continuous Short Circuit Restart Auto-Recovery Line voltage regulation For a 1% change of Vin ±1.2 % Load voltage regulation (5 Vout) 12.8 Load voltage regulation (12 Vout) From 10% load to 100% load 6.8 % Load voltage regulation (15 Vout) 6.3 o Temperature coefficient At 100% load ±0.03 %/ C Ripple & Noise* 20MHz Bandwidth 150 mV p-p Minimum Load Current** 10 % of Max *Test ripple & noise by “Parallel Cable Method” as described in Application Note “Ripple and Noise Measurement of Brick & POL DC-DC Converters” available on Aimtec’s website www.aimtec.com www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.S 1 of 4 North America only Series AM2L-NZ 2 Watt | DC-DC Converter **If the operating output current is less than 10% of maximum it is recommended to install a load resister in parallel with the load to ensure the actual load current meets the minimum load current requirement. General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load, nominal input 100 KHz o Operating temperature -40 to + 85 C o Storage temperature -55 to + 125 C o Maximum case temperature 100 C Cooling Free Air Convection Humidity 95 % RH Case material Plastic(UL94-V0) 1000VDC 2.1 Weight g 6000VDC 3.8 Single & Dual 1000VDC 0.70 x 0.70 x 0.24 inches 17.78 x 17.78 x 6.00 mm Dimensions (L x W x H) Single 6000VDC 0.94 x 0.79 x 0.32 inches 23.86 x 18.50 x 8.00mm MTBF >1,000, 000 hours (MIL-HDBK -217F, Ground Benign, t=+25ºC) o Maximum Soldering Temperature 1.5mm from case for 10 seconds 260 C Safety Specifications Parameters Agency approvals CE (for 6000VDC isolation models) Standards EN 60601-1-1; EN 60601-1-2 Pin Out Specifications 1000VDC 6000VDC Pin Single Dual Pin Single 1 -Vin - Vin 1 - V in 2 + Vin + Vin 2 No Pin 5 NC -Vout 3 No Pin 6 - Vout Common 4 No Pin 7 +Vout +Vout 5 No Pin 8 NC NC 6 No Pin 9 NC NC 7 NC 10 NC -Vout 8 NC 12 NC NC 9 +V out 10 -V out 13 NC NC 11 No Pin 14 NC NC 12 No Pin 13 No Pin 14 No Pin NOTE: On dual output models Pin 5 and Pin 10 are connected internally together. 15 No Pin Either Pin 5 or Pin 10, or both can be used as the -Vout NC: not connected 16 +V in www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.S 2 of 4 North America only Series AM2L-NZ 2 Watt | DC-DC Converter Dimensions 1000VDC Side View 17.78 Front View (0.70) A 2.75 (0.11) 6.00 5.75 (0.24) (0.23) 0.25 (0.01) 2.54 A 1.27 (0.10) (0.05) Top View 0.25 17.78 (0.01) (0.70) 2.54 1.00 2.00 (0.10) (0.04) (0.08) 5.00º angle 14 13 12 10 9 8 1.30 ±0.13 (0.05 ±0.005) MAX 17.78 12.70 (0.70) (0.50) 1 2 3 5 6 7 Dimensions 6000VDC Side View 23.86 Front View (0.94) 8.00 7.50 A (0.32) (0.30) 13.10 2.54 3.04 (0.52) (0.12) (0.10) 18.50 Top View 2.00 (0.73) (0.08) 1.00 (0.04) A 16 10 9 0.50 (0.01) 18.50 13.70 (0.73) (0.54) 5.00º 1 7 8 angle 1.35 ± 0.13 (0.05 ± 0.005) MAX 15.24 (0.60) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.S 3 of 4 North America only Tolerance Envelope Graph Typical Load Line +10% +5% +2.5% -2.5% -7.5% 100% 10% 50% Output Current(%) Output Voltage Series AM2L-NZ 2 Watt | DC-DC Converter Recommended Filter Circuit L L Single Output Dual Output L L +Vout +Vout + Vin + Vin + Cout Cin + + Common Cin + Cout DC DC DC DC + Cout L - Vin -Vout - Vin - Vin If it is required to decrease the input/output ripple an “LC” filter network can be installed on the input and output of the converter (see above). It should be noted that the inductance and the resonant frequency of the “LC” filtering network should differ from the DC/DC converter switching frequency to avoid mutual interference. The capacitance of the outputfilter capacitor must not exceed the values in the Table below to avoid startup problems and ensure safe and reliable operation. It’s not recommended to connect any external capacitor in the application field whenoutput loading is less than 0.5 watt. External Capacitor Tables Input Capacitor (Cin) Output Capacitor (Cout) Single Dual Vin Cin Cout Cout Vout Vout (VDC) (uF) (uF) (uF) (VDC) (Vdc) 5 4.7 5 10 ±5 4.7 12 2.2 15 1 ±12 1 24 1 ±15 0.47 Overload Protection The output circuit of these products has no protection against overload. It is recommended to install external overload protection in the form of a self-recovery fuse or a circuit breaker in series at the converter’s input. To achieve a high degree of output voltage regulation, over-voltage, and over-current protection it is suggested to use the AM2LV-NZ series as an alternative. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.S 4 of 4 North America only