AIMTEC AM30K-2403S-NZ

Click on Series name for product info on aimtec.com Series AM30K-NZ 30 Watt | DC-DC Converter FEATURES:  RoHS compliant  Trim adjustment  Remote On/Off control  Power modules for PCB mounting  High Efficiency up to 90%  Operating temperature range: -40 to +85ºC  Input Under voltage protection  Standard package Models Single output Output Maximum Input Voltage Output Current Efficiency Model Voltage capacitive load (V) max (A) (%) (V) (µF) AM30K-2405S-NZ 18 – 36 5 6 10200 88 AM30K-2412S-NZ 18 – 36 12 2.5 3240 89 AM30K-2415S-NZ 18 – 36 15 2 1100 89 AM30K-2424S-NZ 18 – 36 24 1.25 900 88 AM30K-4805S-NZ 36 – 75 5 6 10200 89 AM30K-4812S-NZ 36 – 75 12 2.5 3240 90 AM30K-4815S-NZ 36 – 75 15 2 1100 90 AM30K-4824S-NZ 36 – 75 24 1.25 900 90 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 12 9-18 Voltage range 24 18-36 VDC 48 36-75 Filter (Pi) Network Start up time 25 ms 12 Vin 20 Absolute Maximum Rating 24 Vin 40 VDC 48 Vin 80 Peak Input Voltage time 100 ms On 3.5 to 12VDC or open circuit Remote On/Off Control Off 0 to 1.2VDC or short circuit between pin 2 and 3 9-18 Vin OFF 8 Under Voltage protection 18-36 Vin OFF 16 VDC 36-75 Vin OFF 33 Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1500 VDC Resistance At 500Vdc >1000 MOhm Capacitance 100KHz / 1V 1000 pF www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.J 1 of 3 North America only Series AM30K-NZ 30 Watt | DC-DC Converter Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±1 % Line voltage regulation LL-HL ±0.2 % of Vin Load voltage regulation 10% to 100% Load ±0.5 % Short Circuit protection Continuous Short Circuit restart Auto Recovery Over current protection Input Voltage Range >120 160 % o Temperature coefficient 0.02 %/ C Ripple & Noise 20MHZ Bandwidth 100 mV p-p Transient Response Recovery 25% load step change 200 μs Time Transient response overshoot ±2 ±5 % of Vout Voltage adjustment range ±10 % General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 300 KHz o Operating temperature With derating above +71°C -40 to +85 C o Storage temperature -55 to +105 C o Case temperature 95 C Cooling Free air convection Humidity 95 % Case material Black Anodized Aluminum Weight 45 g Dimensions (L X W X H) Tolerance ±0.5mm 2.00 x 1.60 x 0.44 inches 50.80 x 40.60 x 11.10mm MTBF >1 000 000 hrs Pin Out Specifications Dimensions 50.80 Pin Single (2.00) 1 +V Input 2 -V Input 3 On/Off Control 4 +V Output 5 -V Output 4 6 Trim 1 Bottom View 2 5 3 6 45.72 (1.80) 2.54 2.54 Printed Face (0.10) (0.10) Dimensions mm(inch) Case Tolerance ±0.50 (±0.02) Pin Pitch Tolerance ±0.35 (±0.014) Ø 1.50 (0.06) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.J 2 of 3 North America only 11.10 40.60 (0.44) (1.60) 5.08 7.62 10.16 4.10 (0.20) (0.30) (0.40) (0.16) 5.10 10.16 10.16 (0.40) (0.20)(0.40) Series AM30K-NZ 30 Watt | DC-DC Converter Trimming Derating Free Air Convection º 71 C 100 80 Safe Operating Area 60 40 20 0 85 100 -40 -20 020 40 60 80 Ambient Temperature º C Recommended EMI Filtering (if required by end application) Note: should your application not require filtering, no additional circuits are required. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.J 3 of 3 North America only Output Power (%)