AIMTEC AM5E-1205D-FZ

Click on Series name for product info on aimtec.com Not recommended for new design Series AM5E-FZ Use AM10E-Z series 5 Watt | DC-DC Converter FEATURES: o o • Over Load, Over Voltage Protection • Operating temperature -55 C to + 85 C • Wide 2:1 input range • Input/Output Isolation 1500VDC • High efficiency up to 87% • Continuous short circuit protection • Pin compatible with multiple manufacturers Models Single output Output Minimum Input Output Current Capacitance Efficiency Model Voltage Load Voltage (V) max (A) load, max (μF) (%) (V) Current (mA) AM5E-1203S-FZ 9-18 3.3 20 1.5 4700 78 AM5E-1205S-FZ 9-18 5 0 1.0 2200 80 AM5E-1212S-FZ 9-18 12 0 0.416 330 85 AM5E-1215S-FZ 9-18 15 0 0.333 220 85 AM5E-2403S-FZ 18-36 3.3 20 1.5 4700 79 AM5E-2405S-FZ 18-36 5 0 1.0 2200 82 AM5E-2412S-FZ 18-36 12 0 0.416 330 86 AM5E-2415S-FZ 18-36 15 0 0.333 220 87 AM5E-4803S-FZ 36-72 3.3 20 1.5 4700 77 AM5E-4805S-FZ 36-72 5 0 1.0 2200 82 AM5E-4812S-FZ 36-72 12 0 0.416 330 85 AM5E-4815S-FZ 36-72 15 0 0.333 220 86 Models Dual output Output Minimum Capacitance Input Output Current Efficiency Model Voltage Load load, max Voltage (V) max (A) (%) (V) Current (mA) (μF) AM5E-1205D-FZ 9-18 ±5 57 ±0.5 1100 82 AM5E-1212D-FZ 9-18 ±12 0 ±0.208 100 84 AM5E-1215D-FZ 9-18 ±15 0 ±0.167 69 85 AM5E-2405D-FZ 18-36 ±5 57 ±0.5 990 83 AM5E-2412D-FZ 18-36 ±12 0 ±0.208 122 86 AM5E-2415D-FZ 18-36 ±15 0 ±0.167 147 87 AM5E-4805D-FZ 36-72 ±5 57 ±0.5 1000 82 AM5E-4812D-FZ 36-72 ±12 0 ±0.208 220 86 AM5E-4815D-FZ 36-72 ±15 0 ±0.167 13 86 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 12 9-18 Voltage range VDC 24 18-36 48 36-72 Filter π(PI ) Start up time 400 ms 12 Vin -0.7-25 Absolute Maximum Rating 24 Vin -0.7-50 VDC 48 Vin -0.7-100 Peak Input Voltage time 100 ms No Load Input Current <3 mA Input reflected current 250 mAp-p Transient recovery deviation ±5 %of Vout www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.B 1 of 3 North America only Not recommended for new design Series AM5E-FZ Use AM10E-Z series 5 Watt | DC-DC Converter Input Specifications (continued) Parameters Nominal Typical Maximum Units Transient response time 50% load step 300 µs change Isolation Specifications Parameters Conditions Typical Rated Units Tested I/Ovoltage 3 sec 1500 VDC Resistance >1000 MOhm Capacitance 24 Vin 580 pF Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±1 % Short Circuit protection Continuous Short circuit restart Auto Recovery Over load protection 150 % Over Voltage Protection Zener Diode Clamp Line voltage regulation LL-HL ±0.5 % Load voltage regulation (Single) 25-100% ±0.5 % 10-100% Balanced ±0.5 % Load voltage regulation (Dual) 25-100% Unbalanced ±5 o Temperature coefficient ±0.02 % C Ripple & Noise 20MHz Bandwidth 75 mVp-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 300 KHz o -55 to +85 Operating temperature C o Storage temperature -55 to +125 C o Maximum case temperature 100 C Cooling Free air convection Humidity 95 % Case material Nickel coated copper Weight 30 g Dimensions (L x W x H) Tolerance ±0.5mm 2.00 x 1.00 x 0.40 inches 50.80 x 25.40 x 10.20 mm o MTBF >1,960,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) o Maximum soldering temperature 1.5mm from case max 10 sec 260 C Pin Out Specifications Pin Single Dual 1 +V Input +V Input 2 -V Input -V Input 3 +V Output +V Output 4 No Pin. Common. 5 -V Output -V Output www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.B 2 of 3 North America only Not recommended for new design Series AM5E-FZ Use AM10E-Z series 5 Watt | DC-DC Converter Dimensions 50.80 (2.00) 3 1 4 Bottom View 2 5 15.24 20.32 15.24 Isolative Plastic base (0.60) (0.80) (0.60) plate Notes: All dimensions are typical in millimeters (inches). Tolerance ±0.25 (±0.01) DIA 1.00 (0.04) Derating Free Air Convection 85 ºC 100 80 60 Safe Operating Area 40 20 0 85 0 40 80 100 -55 -30 20 60 º C Ambient Temperature NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.B 3 of 3 North America only 25.40 10.20 (1.00) (0.40) Output Power % 5.08 (0.20) 5.08 10.16 10.16 Min (0.20) (0.40) (0.40) 10.16 10.16 2.54 2.54 (0.10) (0.40) (0.40) (0.10)