Click on Series name for product info on aimtec.com Series AMEL10-AZ 10 Watt | AC-DC / DC-DC Converter FEATURES: • I/O Isolation 3000VAC • RoHS Compliant o o • Operating Temp: -40 C to +80 C • Energy Star Compliant • Input: 90-305VAC, 47-440Hz, or 130-430VDC • Efficiency up to 83% • Over Load, Over Voltage, Short Circuit Protection • Soft Start Models CB Single output Maximum Efficiency Input Input Temperature Output Output (%) capacitive Model Voltage Voltage range Voltage Current Load 115 230 277 (VAC/Hz) (VDC) (ºC) (V) max (A) VAC VAC VAC (µF) AMEL10-3.3SAZ 90-305/47-440 130-430 -40 to +80 3.3 3.00 2200 69 70 70 AMEL10-5SAZ 90-305/47-440 130-430 -40 to +80 5 2.00 1000 73 74 74 AMEL10-12SAZ 90-305/47-440 130-430 -40 to +80 12 0.84 680 79 80 81 AMEL10-15SAZ 90-305/47-440 130-430 -40 to +80 15 0.67 470 79 80 80 AMEL10-24SAZ 90-305/47-440 130-430 -40 to +80 24 0.42 470 78 79 79 Note: Optional mounting plate version can be ordered by adding “-ST” suffix to part number (ex. AMEL10-5SAZ-ST) Input Specifications Parameters Conditions Typical Maximum Units 115 VAC  230 mA 230 VAC 150 mA Current (full load)  277 VAC 140 mA  115 VAC 20 A  Inrush current <2ms (cold start) 230 VAC  35 A 277 VAC  50 A Leakage current 0.25 mA  External fuse Recommended slow blow type 1 A Input dissipation (110/230/277 VAC) W ≦0.2 Start-up time 50 ms Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±2 % Line regulation ±1 % Load regulation 0-100% load ±2 % Transient recovery time 500 µs Transient response deviation 25% load step ±2 % of Vout 3.3/5V models 75 mV p-p Ripple & Noise* 12/15V models 100 mV p-p 24V models 150 mV p-p Hold-up time 15 ms * Ripple and Noise are measured at 20MHz bandwidth & 230VAC by using a 0.1µF (M/C) and 47µF (E/C) parallel capacitor. Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 3000 VAC Isolation Resistance >1000 MΩ General Specifications Parameters Conditions Typical Maximum Units Switching frequency 66 KHz Over load protection Foldback 130 % www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.N 1 of 5 North America only Series AMEL10-AZ 10 Watt | AC-DC / DC-DC Converter Over voltage protection Zener Diode Clamp Short circuit protection Auto recovery o Operating temperature With derating over 60ºC Refer to model application C o Storage temperature -40 to +95 C o Maximum case temperature 100 C o Temperature coefficient ±0.02 % / C Cooling Free air convection Humidity Non condensing 20 ~ 95 % RH Case material Plastic (flammability to UL 94V-0) Weight 70 g Dimensions (L x W x H) 56.48 x 30.86 x 25.10mm (2.22 x 1.21 x 0.99inches) o > 400 000 hrs (MIL-HDBK -217F, t=+25 C)/ Full Load MTBF > 100,000 hrs (MIL-HDBK -217F, t=at highest operating temperature)/Full Load NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine Displacement 1mm Vibration Acceleration 3g Converter operation 10-100Hz, speed 0.05Hz/s Safety Specifications Parameters Agency approvals cULus, CE, CB Information technology Equipment EN 60950-1:2006+A11:2009 EMI - Conducted and radiated emission EN55022, class B Harmonic Current Emissions IEC/EN 61000-3-2, Class A Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV/Air ±8KV, Criteria A RF, Electromagnetic Field Immunity IEC 61000-4-3, 3V/m, Criteria A Standards Electrical Fast Transient/Burst Immunity IEC 61000-4-4, ±1KV, Criteria A Surge Immunity IEC 61000-4-5, ±1KV, Criteria A RF, Conducted Disturbance Immunity IEC 61000-4-6, 3Vrms, Criteria A Power frequency Magnetic Field Immunity IEC 61000-4-8, 1A/m, Criteria A Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Information Technology Equipment UL 60950-1:2007 Information Technology Equipment CAN/CSA-C22.2 No.60950-1-07 www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.N 2 of 5 North America only Series AMEL10-AZ 10 Watt | AC-DC / DC-DC Converter Additional Surge Protective Circuitry The AMEL10-AZ series design level surge protection is certified to IEC 61000-4-5 surge Line to Line of 1KV. However greater protection can be enhanced by adding protective devices to ingress circuitry. For example, by adding an MOV (Metal Oxide Varistor) device example S14K320E2 to the N / L input lines 2KV surge protection or greater, can be achieved. L Fuse + Vo+ Aimtec MOV AC-DC Converter N - Vo- Vrms Vdc Wmax (2ms) Pmax MOV PN V V J W S14K320E2 320 420 136 0.6 Pin Out Specifications Pin Single 1 AC Input (L) 2 AC Input (N) 3 +V Output 4 -V Output 5 No pin Derating º 60 C 100 80 Safe Operating Area 60 40 20 0 80 - 40 - 20 0 20 40 60 100 º C Ambient Temperature www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.N 3 of 5 North America only Output Power (%) Load Series AMEL10-AZ 10 Watt | AC-DC / DC-DC Converter Dimensions 56.46 (2.22) 45.72 (1.80) 3 1 3 4 1 Top View 4 Top View 2 5 2 5 5.37 5.37 (0.21) (0.21) DIV: 10.00 (0.40) 5Ø 1.0 (Ø 0.04) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) 1.05 Pin Diameter 1.0 ± 0.05 (0.04 ± 0.002) (0.04) Pin Pitch Tolerance ±0.5 (±0.02) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.N 4 of 5 North America only 30.86 (1.21) 25.10 5,27 20.40 5.27 (0.99) (0.21) (0.80) (0.21) 6.00 (0.24) 10.20 10.20 (0.40) (0.40) Series AMEL10-AZ 10 Watt | AC-DC / DC-DC Converter Dimensions of Optional ST Mounting Plate Version Pin Out Specification ST Version 86.00 70.00 AIMTEC NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.N 5 of 5 North America only 38.00 25.00