Click on Series name for product info on aimtec.com Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver FEATURES: • AC-DC Constant current LED Driver • Over Temperature Protection • Input range 90-277VAC/47-440Hz • Open frame • High Efficiency up to 86% • Power Factor Correction • Operating temperature -40 to 80°C • SCP, Over Current Protection • Dimmable via analog / 0-10Vdc / PWM • 5 Years Limited Warranty (C version see table) Models Single output Max Output Output Output Input Voltage Input Voltage Efficiency Model Voltage Current Power (VAC/Hz) (VDC) (%) Range (V) (A) (W) * AMEOR30-5070AZ 35 36-50 0.7 90-277/47-440 130-390 86 AMEOR30-4864AZ 30.72 36-48 0.64 90-277/47-440 130-390 86 AMEOR30-36100AZ 36 24-36 1 90-277/47-440 130-390 85 AMEOR30-24140AZ 33.6 12-24 1.4 90-277/47-440 130-390 84 AMEOR30-12250AZ 30 5-12 2.5 90-277/47-440 130-390 83 *Exceeding the maximum output power will permanently damage the converter All models can be ordered with optional North American colour input wires (black (L), white (N), green (GND)). Add “–NA” to part number when ordering. NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230/277VAC) and at rated output load unless otherwise specified. See http://www.aimtec.com/terms-sale AMEOR30-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Conditions Typical Maximum Units 115VAC 25 Inrush current <2ms A 230VAC 40 115VAC 0.3 Leakage current mA 230VAC 0.5 115VAC 0.33 AC current A 230VAC 0.16 115VAC 0.99 Power Factor 230VAC 0.97 External fuse 250V/1A Start up time 450 ms Surge voltage 2sec 440 V Output Specifications Parameters Conditions Typical Maximum Units Current accuracy ±3 % Line regulation LL-HL ±1 % Load regulation 0-100% load ±3 % Ripple & Noise * 20MHz Bandwidth 75 mV p-p Hold-up time 50 ms Current adjustment range 100-0 % Minimum Load Voltage See the models table * Tested with 0.1µF (M/C) or (C/C) and 47µF (E/C) parallel capacitors at the end. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 1 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 3sec 3000 VAC Isolation Resistance >1000 MΩ General Specifications Parameters Conditions Typical Maximum Units Switching frequency 130 KHz AMEOR30-5070AZ 0.77 AMEOR30-4864AZ 0.68 Over current protection AMEOR30-36100AZ 1.04 A AMEOR30-24140AZ 1.45 AMEOR30-12250AZ 2.55 Over voltage protection Refer to Constant Current vs. Constant Voltage Mode curve Short circuit protection Continuous Short circuit restart Auto recovery Over temperature protection >105°C o Operating temperature With derating over 60°C -40 to +80 C o Maximum case temperature 100 C o Storage temperature -40 to +95 C o Temperature coefficient ±0.02 % / C Cooling Free air convection Humidity 95 % RH Wires UL1015 18AWG * 20CM Weight 220 g Dimensions (L X H X W) 5.83 x 1.97 x 1.3 inches 148 x 50 x 33 mm MTBF >400,000 hrs (MIL-HDBK-217F at +25°C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1 mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals cULus, CE UL8750, UL60950-1, EN55022, class B Information Technology Equipment EN55022 Class B Harmonic Current Emissions IEC/EN 61000-3-2, Class C Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 Standards RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Electrical Fast Transient / Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 3 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 1 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 2 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Top View Dimensions 148.00 (5.83) 139.00 (5.47) 4 Mounting Holes-M3 4.50 (0.18) 200.00 (8.00) Side View 200.00 (8.00) Input/Output Wires are 18 AWG 20cm NOTE: to adjust the output current connect a 20K Ohm pot between blue and white wire Wire connection: Connection Wire Brown AC L Blue AC N Green Ground Red +V output Black -V Output Blue (Dimming) + Vs dimming White (Dimming) -Vs dimming AMEOR30-AZ Analog (resistive) Dimming Application Circuit BROWN RED +Vout L st Maximum Pot GREEN 1 LED Model Number 1 AC Value (kΩ) AMEPR30-AZ AMEPR30-5070AZ 9.00 -Vout AMEPR30-4864AZ 9.00 N 1 AMEPR30-36100AZ 9.00 BLUE AMEPR30-24140AZ 26.00 BLUE AMEPR30-12250AZ 26.10 BLACK Pot WHITE www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 3 of 17 North America only 28.00 (1.10) 50.00 (1.97) 41.00 (1.61) 4.50 (0.18) 5.00 (0.20) Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-AZ Analog (0-10V) Dimming Application Circuit AMEOR30-AZ PWM (1KHz) Dimming Application Circuit Temperature graph Free Air Convection 55 º C 100 80 Safe Operating Area 60 40 20 0 85 100 -40 -20 0 20 40 60 80 Ambient Temperature º C www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 4 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Efficiency Vs. Input Voltage & Output Current (Constant current load) AMEOR30-5070AZ AMEOR30-4864AZ (%) Efficiency Vs. Input Voltage & Output Current 110Vac 110Vac, 0.128, 73.8 230Vac, 0.64, 86.4 230Vac 110Vac, 0.64, 86.2 230Vac, 0.128, 68.2 (A) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 5 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Efficiency Vs. Input Voltage & Output Current (Constant current load) (continued) AMEOR30-36100AZ (%) Efficiency Vs. Input Voltage & Output Current 110Vac 230Vac, 1, 88.0 230Vac 110Vac, 1, 87.9 110Vac, 0.2, 81.4 230Vac, 0.2, 74.6 (A) AMEOR30-24140AZ www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 6 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Efficiency Vs. Input Voltage & Output Current (%) 230Vac, 1.7, 87.5 110Vac 230Vac 110Vac, 1.7, 86.6 110Vac, 0.34, 81.6 230Vac, 0.34, 79.4 (A) AMEOR30-12250AZ www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 7 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver PFC Value vs. Output Load Current (constant current mode) AMEOR30-5070AZ PFC Value vs. Output Load Current (constant current mode) (continued) AMEOR30-4864AZ PFC value Vs. Output Load Current (value) 115VAC 115VAC, 50%, 0.98 115VAC, 100%, 1.00 230VAC 230VAC, 100%, 0.94 230VAC, 50%, 0.77 (load) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 8 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-36100AZ PFC value Vs. Output Load Current (value) 115VAC 115VAC, 100%, 0.99 115VAC, 50%, 0.98 230VAC 230VAC, 100%, 0.96 230VAC, 50%, 0.88 (load) PFC Value vs. Output Load Current (constant current mode) (continued) AMEOR30-24140AZ (value) PFC value Vs. Output Load Current 115VAC, 100%, 1.00 115VAC 230VAC 115VAC, 50%, 0.98 230VAC, 100%, 0.96 230VAC, 50%, 0.91 (load) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 9 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-12250AZ PFC value Vs. Output Load Current (value) 115VAC 115VAC, 50%, 0.98 115VAC, 100%, 1.00 230VAC 230VAC, 100%, 0.94 230VAC, 50%, 0.77 (load) Constant Current vs. Constant Voltage Mode AMEOR30-5070AZ Constant Current Vs. Constant Voltage (A) 0.80 50 36 Normal 0.70 Input 0.60 0.50 0.40 0.30 0.20 0.10 52 50.4 0.00 36 38 40 42 44 46 48 50 52 54 (V) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 10 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-4864AZ Constant Current Vs. Constant Voltage (A) 36 38 Normal Input, 36, 0.64 Normal Input, 48, 0.64 40 42 44 46 47 48 Normal Input, 48.4, 0.00 Normal Input, 50, 0.00 (V) Constant Current vs. Constant Voltage Mode (continued) AMEOR30-36100AZ Constant Current Vs. Constant Voltage (A) Normal Input, 36, 1.02 24 26 Normal Input, 24, 1.00 28 30 32 34 35 36 Normal Input, 36.4, Normal Input, 38, 0.00 0.00 (V) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 11 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-24140AZ Constant Current Vs Constant Voltage (A) 1.6 12.0 24.0 115 & 1.4 230 Vac 1.2 1.0 0.8 0.6 0.4 0.2 26.0 24.7 0.0 12 14 16 18 20 22 24 26 28 (V) Constant Current vs. Constant Voltage Mode (continued) AMEOR30-12250AZ Constant Current Vs. Constant Voltage (A) Normal Input, 12, 5 6 Normal Input, 5, 2.51 2.54 7 8 9 10 11 12 Normal Input, 14, Normal Input, 12.3, 0.00 0.00 (V) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 12 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Dimming Control (Output Current vs. Radj) AMEOR30-5070AZ Output Current vs. Resistance adjustment (A) 120% 9.00 Normal Input 100% 1.66 0.79 80% 0.45 60% 0.25 0.15 40% 0.07 0.02 20% 0.01 0.01 0% 0.007 0 2 4 6 8 10 K(Ω) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 13 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Dimming Control (Output Current vs. Radj) (continued) AMEOR30-4864AZ Output Current vs. Resistance adjustment (A) 0.007 0.01 Normal Input, 9.00 , 0.02 100% 0.02 Normal Input, 1.66 , 0.07 90% 0.15 Normal Input, 0.79 , 0.25 80% Normal Input, 0.45 , 70% Normal Input, 0.25 , 60% Normal Input, 0.15 , 50% Normal Input, 0.07 , 40% Normal Input, 0.02 , 30% Normal Input, 0.02 , 20% Normal Input, 0.01 , 10% Normal Input, 0.007, 0% K(Ω) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 14 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-36100AZ Output Current vs. Resistance adjustment (A) 0.007 0.01 0.02 0.02 Normal Input, 9.00 , 0.07 0.15 100% 0.25 0.45 Normal Input, 1.66 , 90% 0.79 1.66 9.00 Normal Input, 0.79 , 80% Normal Input, 0.45 , 70% Normal Input, 0.25 , 60% Normal Input, 0.15 , 50% Normal Input, 0.07 , 40% Normal Input, 0.02 , 30% Normal Input, 0.02 , 20% Normal Input, 0.01 , 10% Normal Input, 0.007, 0% K(Ω) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 15 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver Dimming Control (Output Current vs. Radj) (continued) AMEOR30-24140AZ Output Current vs. Resistance adjustment (A) 0 0.01 Normal Input, 26.00 , 0.02 100% Normal Input, 4.26 , 0.10 90% 0.15 Normal Input, 1.50 , 0.25 80% Normal Input, 0.88 , 70% Normal Input, 0.45 , 60% Normal Input, 0.25 , 50% Normal Input, 0.15 , 40% Normal Input, 0.10 , 30% Normal Input, 0.02 , 20% Normal Input, 0.01 , 10% Normal Input, 0, 0% K(Ω) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 16 of 17 North America only Series AMEOR30-AZ up to 2.5A | AC-DC / DC-DC LED driver AMEOR30-12250AZ Output Current vs. Resistance adjustment (A) 0 0.00 Normal Input, 26.10 , 0.00 100% Normal Input, 4.29 , 0.00 90% 0.11 Normal Input, 1.84 , 0.35 80% Normal Input, 0.88 , 70% Normal Input, 0.50 , 60% Normal Input, 0.35 , 50% Normal Input, 0.11 , 40% Normal Input, 0.00 , 30% Normal Input, 0.00 , 20% Normal Input, 0.00 , 10% Normal Input, 0, 0% K(Ω) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. . www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.K 17 of 17 North America only