Click on Series name for product info on aimtec.com Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter FEATURES: • Open Frame design • Very wide input range • 4000 VAC Isolation • Low Ripple & Noise • 3 or 4 wire three phase input • High Efficiency • Over-voltage protection • Low Standby Power < 0.55W Models Dual output Maximum Input Temperature Output Output Input Voltage capacitive Efficiency Model Voltage range Voltage Current max (VAC/Hz) load (%) (VDC) (ºC) (V) (A) (µF) 5.1 1.2 4000 AMEOW10-5S12S-NZ 65-460 / 47-440 90-650 -40 to +70 78 12 0.4 1200 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. All specifications are in reference to input voltage Vin=220VAC. Input Specifications Parameters Conditions Typical Maximum Units Vin=220VAC 100 mA Current Vin=220VAC 25A A Inrush current <2ms Leakage current Vin=220VAC 0.3 mA External fuse Slow Blow Type 3.15A 250V A Input dissipation Vin=220VAC, 100% load 13.5 W Under voltage protection 56 VAC Input Over Voltage Shutdown 750 ± 50 Vdc Output Specifications Parameters Conditions Typical Maximum Units Vo1: 5 Voltage accuracy % Vo2: ± 10 Vo1: ± 0.5 Line regulation 10 – 100% % Vo2: ± 1.5 Vo1: ± 3 Load regulation Balanced Load % Vo2: ± 5 Vo1: ± 3 Cross regulation % Vo2: ± 12 Transient recovery time 2000 µs Transient response deviation Vin=220VAC ± 100 mV V1: 100 Ripple & Noise 20MHz Bandwidth mV p-p V2: 200 Hold-up time (min) 200 ms V1: ± 3 Voltage adjustment range % V2: ± 10 Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60s > 50MΩ 4000 VAC Output V1 V2 Isolation 4000 VAC Reinforced isolation General Specifications Parameters Conditions Typical Maximum Units Switching frequency 63 KHz Start up time 500 mS www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.B 1 of 5 North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter General Specifications (continue) Parameters Conditions Typical Maximum Units Over current protection Io1 & Io2 = 100% 110~250%, Auto Recovery % Over voltage protection Clamp Diode % Short circuit protection Continuous Short circuit restart Auto Recovery o Operating temperature Altitude < 3000 meters -40 to +70 C o Storage temperature -40 to +85 C Cooling Free Air Convection V1: ±0.02 o Temperature coefficient % / C V2: ±0.06 Humidity 20 - 90 % RH Weight 95 g Dimensions (L x W x H) 3.94 (L) x 1.97 (W) x 1.38 (H) inches 100 (L) x 50 (W) x 35 (H) mm MTBF > 300,000h @25°C Environment Approval Test Parameters Conditions Acceleration amplitude 196.1 m/s² Shock Bump duration 11 ms Number of bumps Along x, y, z, once each Test mode 10 ~ 55 Hz Displacement 3 minutes / cycle Vibration 19.6 m/s² Acceleration Converter operation 60 minutes Safety Specifications Parameters Standards Designed to meet : IEC EN61000-4-4, IEC EN61000-4-5, EN 55022 class B Pin Out Specifications Pin Designation 1 AC Input (L) 2 AC Input (N) 3 Output +12 V 4 Output -12 V 5 Output -5 V 6 Output +5 V www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.B 2 of 5 North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Typical Applications C1 C2 TVS RL + + L L Vo1 - C3 C4 RL - L/N N Vo2 + + Device Value C1 220 µF / 10V C2 0.1 µF / 50V C3 100µF / 25V C4 0.1 µF / 50V TVS TVS 600W 6.8V UNIDIRECT DO204AC P6KE6.8A It is recommended that the 5V output adds TVS (transient voltage suppressor) to protect adjacent circuits (if device fails), the 12 V output has TVS protection internally, so not required. Three phase four wire full wave rectification application: Common Mode Winding Resistor Inductor >3mH + L 5 ~ 10Ω L1 47 560K + Vo1 FUSE 3.15A µF Ω 560K Winding Resistor - Ω 5 ~ 10Ω L2 FUSE 3.15A 560K - Ω Winding Resistor 47 + 560K 5 ~ 10Ω µF Vo2 Ω L3 FUSE 3.15A + Varistor N 911KD20 N Capacitor 0.1µF Capacitor 0.1µF FUSE 3.15A IN4007X2 300VAC Safety X1 300VAC Safety X1 Level Level www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.B 3 of 5 North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Three phase four wire half wave rectification application: Common Mode Winding Inductor >3mH + L Resistor 5 ~ 10Ω L1 47 560K + Vo1 FUSE 3.15A µF Ω 560K Winding Resistor - IN4007X2 Ω 5 ~ 10Ω L2 FUSE 3.15A - 560K Ω Winding Resistor 47 + 560K 5 ~ 10Ω µF Vo2 Ω L3 FUSE 3.15A Varistor N + 911KD20 N Capacitor 0.1µF Capacitor 0.1µF FUSE 3.15A 300VAC Safety X1 300VAC Safety X1 Level Level Derating Free Air Convection º C 60 100 80 Safe Operating Area 60 40 20 0 - 40 100 - 20 0 20 40 60 80 º C Ambient Temperature www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.B 4 of 5 North America only Output Power % Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Dimensions Dimensions mm (inch) 4.5 (0.17) 1 6 10 (0.39) 5 Φ 2 ± 0.15 4 3 2 4 (0.16) 92 (3.62) ±1 ±0.04 100 (3.94 ) ±0.15 ±0.006 2.5 (0.10 ) 0.5 (0.02) 1.2 (0.05) ±0.15 ±0.006 1.5 (0.06 ) 92 (3.62) ±1 ±0.04 100 (3.94 ) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052e R8.B 5 of 5 North America only 35 (1.38) MAX 4.8 (0.19) ±1 ±0.04 50 (1.97 ) 41 (1.61) 31 (1.22) 41 (1.61) 4.8 (0.19) 1.6 (0.06)