Click on Series name for product info on aimtec.com Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver FEATURES:  AC-DC Constant current LED Driver  Over Temperature Protection  Input range 90-264VAC/47-440Hz  IP20 and IP67 Case ②  High Efficiency up to 81%  Active PFC with TRIAC dimmable  Operating temperature -20 to 80°C  SCP, Over Voltage Protection  Total Harmonic Distortion < 20%  Leading or Trailing Edge Triac  5 Year Limited Warranty Models Single output No Load Max Efficiency Output Output Output (%) Output Voltage Input Voltage Model Current Voltage Power Range (VAC/Hz) 115 230 (A) (V max.)  ① (W) (V) VAC VAC +Suffix② 10 36-50 62 0.2 90-264/47-440 AMEPR10D-5020AZ 78 79 ② +Suffix 10 30-40 62 0.25 90-264/47-440 AMEPR10D-4025AZ 81 80 ② +Suffix 10.8 24-36 52 0.3 90-264/47-440 AMEPR10D-3630AZ 80 81 ② +Suffix 10.5 15-30 34 0.35 90-264/47-440 AMEPR10D-3035AZ 77 78 ② +Suffix 9.6 8-15 23 0.64 90-264/47-440 AMEPR10D-1564AZ 77 76 ② +Suffix 8.4 5-12 23 0.7 90-264/47-440 AMEPR10D-1270AZ 78 79 ①  Exceeding the maximum output power will permanently damage the converter. ② Model Nomenclature for Ordering: Add Suffix “-UD” Universal AC input 90-264VAC (no TRIAC dimming option), IP20 Add Suffix “-UW” Universal AC input 90-264VAC (no TRIAC dimming option), IP67 Add Suffix “-110D” AC input 90-135VAC, IP20 Add Suffix “-110W” AC input 90-135VAC, IP67 Add Suffix “-220D” AC input 180-264VAC, IP20 Add Suffix “-220W” AC input 180-264VAC, IP67 NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See http://www.aimtec.com/terms- sale AMEPR10D-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Conditions Typical Maximum Units 115VAC 15 Inrush current <2ms (cold start) A 230VAC 25 115VAC 0.2 Leakage current mA 230VAC 0.25 115VAC 110 Current (Full Load) mA 230VAC 55 115VAC 0.9 Power Factor 230VAC 0.9 External fuse (slow blow) Recommended slow blow Type 1 A Start up time 200 ms www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.P 1 of 4 North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Output Specifications Parameters Conditions Typical Maximum Units Current accuracy ±7 % Line regulation (LL-HL) ±10 % Load regulation 0-100% load ±7 % ③ Ripple & Noise 3 V p-p Hold-up time 1 ms Minimum Load Voltage See the models table ③ Ripple and Noise are measured at 20MHz bandwidth by using a 0.1μF (M/C) or (C/C) and 47µF (E/C) parallel capacitor. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 60 sec 3000 VAC Isolation Resistance >1000 MΩ General Specifications Parameters Conditions Typical Maximum Units Switching frequency 65 KHz Over load protection �110 % Over voltage protection ≥110 % Short circuit protection Auto recovery Over temperature protection >105°C o With derating over 55°C C Operating temperature -20 to +80 (for IP67 case) o Maximum case temperature 100 C o Storage temperature -40 to +95 C o Temperature coefficient ±0.02 % / C Cooling Free air convection Humidity 95 % RH Case material Plastic Wires UL1015 Input 18AWG*10CM/ Output 20 AWG * 10CM IP20 160 Weight g IP67 200 Dimensions (L X H X W) 133 x 33 x 30mm (5.24 x 1.30 x 1.18 inch) MTBF >400,000 hrs (MIL-HDBK-217F at +25°C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1 mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.P 2 of 4 North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Safety Specifications Parameters Agency approvals cULus, CE, FCC EN61347-1, EN61347-2-13, IEC62384, UL8750, UL60950-1, EN55015, EN55024, FCC part 15 Subpart B, Class B, ANSI C63.4 :2003 Harmonic Current Emissions IEC/EN 61000-3-2, Class C Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Standards Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 1 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 2 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Dimensions www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.P 3 of 4 North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Temperature Graph Triac Dimming Feature Triac Device LED Lighting  LED Driver Application AC Red (+) Line (Brown) Aimtec Neutral (Blue) Black (-) Earth  Ground Triac Dimming Notes: A-The triac device can be installed on either Line or Neutral B-Aimtec LED drivers have been designed to function with a wide  range of available Triac devices, however the following list of Triac  devices have been tested. 1) Company: LUTRON Series: SKYLARK Model: SF-10P-WH (input voltage: 120Vac) Model: SF-12P-277-WH (input voltage 277Vac) 2) Company LUTRON Series: DIVA Model: DVF-103P-WH (input voltage: 120Vac) Model: DVF-103P-277-WH (input voltage: 277Vac) 3) Company BERKER Model: 2867 10 (input voltage:230Vac) If the power voltage range is 90~135Vac, triac suggested use model  SF-10P-WH or DVF-103P-WH. If the power voltage range is 180~260Vac, triac suggested use  model SF-12P-277-WH or DVF-103P-277-WH. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.P 4 of 4 North America only