Click on Series name for product info on aimtec.com Series AMEPR15D-AZ up to 1A | AC-DC LED Driver FEATURES:  AC-DC Constant Current LED Driver  Leading or Trailing Edge Triac  Input range 90-264VAC/47-440Hz  IP20 or IP67 Case ②  High Efficiency up to 82%  Active PFC with TRIAC Dimmable  Operating temperature -20 to 80°C  SCP, Over Load Protection  Total Harmonic Distortion < 20%  5 Year Limited Warranty Models Single Output No Load Max Output Efficiency Output Output Voltage Output Input Voltage (%) Model Voltage Power Range Current (A) (VAC/Hz) 115 230 ① (W) (V max.) VAC VAC (V) ② +Suffix 15 36-50 62 0.3 90-264/47-440 82 82 AMEPR15D-5030AZ ② +Suffix 15.8 30-48 62 0.35 90-264/47-440 82 82 AMEPR15D-4835AZ +Suffix② AMEPR15D-3650AZ 18 24-36 52 0.5 90-264/47-440 81 82 +Suffix② AMEPR15D-2470AZ 16.8 12-24 34 0.7 90-264/47-440 81 82 +Suffix② AMEPR15D-15100AZ 15 8-15 23 1 90-264/47-440 80 79 ① Exceeding the maximum output power will permanently damage the converter. ② Model Nomenclature for Ordering: Add Suffix “-UD” Universal AC input 90-264VAC, (no TRIAC dimming option), IP20 Add Suffix “-UW” Universal AC input 90-264VAC, (no TRIAC dimming option), IP67 Add Suffix “-110D” AC input 90-135VAC, IP20, 115VAC typical value Add Suffix “-110W” AC input 90-135VAC, IP67, 115VAC typical value Add Suffix “-220D” AC input 180-264VAC, IP20, 230VAC typical value Add Suffix “-220W” AC input 180-264VAC, IP67, 230VAC typical value NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See http://www.aimtec.com/terms- sale AMEPR15D-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Conditions Typical Maximum Units 115VAC 15 Inrush current <2ms (cold start) A 230VAC 25 Leakage current 25 mA 115VAC 400 AC current mA 230VAC 250 115VAC 0.9 Power Factor 230VAC 0.9 Recommend Slow External fuse 1 A Blown Type Start up time 200 ms www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.R 1 of 5 North America only Series AMEPR15D-AZ up to 1A | AC-DC LED Driver Output Specifications Parameters Conditions Typical Maximum Units Current accuracy ±7 % Line regulation LL-HL ±10 % Load regulation 0-100% load ±7 % ③ Ripple & Noise 3 V p-p Hold-up time 1 ms Minimum load voltage See the models table ③ Ripple and Noise are measured at 20MHz bandwidth by using a 0.1μF (M/C) or (C/C) and 47µF (E/C) parallel capacitor. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 3sec 3000 VAC Isolation resistance >1000 MΩ General Specifications Parameters Conditions Typical Maximum Units Switching frequency 65 KHz Over load protection 110 % Over voltage protection 110 % Short circuit protection Auto recovery Short circuit restart Over temperature protection >105°C o With derating over 55°C C Operating temperature -20 to +80 (for IP67 case) o Maximum case temperature 100 C o Storage temperature -40 to +95 C o Temperature coefficient ±0.02 % / C Cooling Free air convection Humidity 95 % RH Case material Plastic Wires UL1015 Input 18AWG*10CM / Output 20 AWG*10CM IP20 160 Weight g IP67 200 Dimensions (L X H X W) 133 x 33 x 30mm (5.24 x 1.30 x 1.18 inch) MTBF >400,000 hrs (MIL-HDBK-217F at t=+25°C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1 mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.R 2 of 5 North America only Series AMEPR15D-AZ up to 1A | AC-DC LED Driver Safety Specifications Parameters Agency approvals cULus, CE, FCC EN61347-1, EN61347-2-13, IEC62384, UL8750, UL60950-1, EN55015, EN55024, FCC Part 15 Subpart B, Class B, ANSI C63.4 :2003 Harmonic Current Emissions IEC/EN 61000-3-2, Class C Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Standards Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 1 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 2 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Dimensions Free Air Convection Temperature graph º C 55 100 80 Safe Operating Area 60 40 20 0 -25 100 -20 020 40 60 80 º C Ambient Temperature www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.R 3 of 5 North America only Output Power % Series AMEPR15D-AZ up to 1A | AC-DC LED Driver Triac Dimming Feature Triac Device LED Lighting  LED Driver Application AC Red (+) Line (Brown) Aimtec Neutral (Blue) Black (‐) Earth  Ground Triac Dimming Notes: A‐ The triac device can be installed on either Line or Neutral B‐ Aimtec LED drivers have been designed to function with a wide  range of available Triac devices, however the following list of Triac  devices have been tested. 1) Company: LUTRON      Series: SKYLARK      Model: SF‐10P‐WH (input voltage: 120Vac)      Model: SF‐12P‐277‐WH (input voltage 277Vac) 2) Company LUTRON      Series: DIVA      Model: DVF‐103P‐WH (input voltage: 120Vac)      Model: DVF‐103P‐277‐WH (input voltage: 277Vac) 3) Company BERKER      Model: 2867 10 (input voltage:230Vac) If the power voltage range is 90~135Vac, triac suggested use model  SF‐10P‐WH or DVF‐103P‐WH. If the power voltage range is 180~260Vac, triac suggested use  model SF‐12P‐277‐WH or DVF‐103P‐277‐WH. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.R 4 of 5 North America only Series AMEPR15D-AZ up to 1A | AC-DC LED Driver Triac Dimming Performance AMEPR15D-2470AZ (mA) Dimming Performance(Input 110Vac) 800 NS‐1223B 675  700 621  LUTRON DVCL‐ 600 558  15SP‐WH 500 387  400 300 307  200 100  100 60  80  0 20 40 60 80 100 120 140 160 Angle (mA) Dimming Performance(Input 230 Vac) 800 701  NS‐1223C 700 626  607  664  Berker 286710 600 572  500 LUTRON LLSI‐ 386  502B‐FAW‐M 400 311  300 267  200 98  100 116  49  102  2  0 20 70 120 170 220 Angle Triac dimming performance is typical as with other models, for specific details on other model performance, please see the Aimtec Triac Dimming Application note at www.aimtec.com NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.R 5 of 5 North America only