® 3 Position Mini PL SPEC Pak is a rugged and environmentally sealed (IP68) connector with a manually operated release ® latch. The 3 Position Mini PL leverages PowerMod pin and socket contact technology, delivering capabilities up to 22 amps at 600 volts while handling wires from 24 to 12 AWG (0.5 to 2.5 mm²). The 30µ gold plated pins are available in 3 lengths, enabling sequenced contact mating options. These contacts sit inside a UV and flame resistant shells that are touch safe on both sides. Features Manual Release Latch • Prevents accidental un-mating Pin & Socket Contact Technology • Gold plated for greater conductivity 3 Pin Lengths Available • Offers sequencing capabilities Touch Safe per UL 1977 Sec. 10.2 • Touch safe on both pin & socket sides Mechanical Rugged & Environmentally Sealed Shells Environmental Seal • F1 weatherability rating per UL 746C IEC IP 68 • V0 flammability rating per UL 94 UL 50E • IP68, exceeds industry standards Wire Size 24 to 12 AWG 0.5 to 2.5 mm² Materials Shell PC Sealing Options Sealing Gland Latch PC Operating Temperature -20 to 105°C -4 to 221°F” Flammability UL 94 V-0 Mating Cycles (no load) 500 Electrical Weatherability UL764C / 12 mm, F1 Current Rating (Amperes) Contact Retention Force 10 lbf Contacts UL 1977 22 44 N Socket Body Copper Alloy, CSA (30°C Rise) 16 200 µ inch Sn over Ni Mating Force (nominal) 5 lb Voltage Rating 22 N Socket Contact Copper Alloy, UL 1977 (AC/DC) 600 30 µ inch Au over Ni Touch Safe (UL 1977 Sec 10.2) Pass Dielectric Withstanding (AC) 2200 Pin Copper Alloy, Latch Strength (nominal) 24 lb 30 µ inch Au over Ni Contact Resistance (average) 3 Milliohms 107 N NOTE: Sn = tin Ni = nickel Au = Gold All Data Subject To Change Without Notice UL Pending Step 2 - Select Sealing Gland | ORDERING INFORMATION | ® SPEC Pak Mini PL Series is a highly configurable Step 1 - Select Shell environmentally sealed connector that can be purchased as component in bulk for volume production, or pre-packaged as a kit. Configuring a connector is an easy three step process. Step 3 - Select Contacts Step 1: Select Shell ® SPEC Pak Shell Kits (sealing glands & contacts sold separately) Description - Part Numbers - Mates With: OR Minimum Quantity ............... 25 ... Male, Receptacle Shell SK1-019M03 Female, Plug SK6-019M03 Female, Jam Nut SK7-019M03 SK1-019M03 SK6-019M03 SK7-019M03 Female, Cover SK9F-019 Male Receptacle Female Plug Female Panel, Jam Nut Male, Cover SK9M-019 Step 2: Select Sealing Gland FAQ Q: Do I need a sealing gland? A: For IP68 rating, sealing glands are required with SK1-019M03 & SK6-019M03. A: For splash resistance in the unmated condition, use optional wire sealing grommets with SK7-019M03. (See accessories on page 4). Q: How do I select the appropriate sealing gland? A: Identify the number of wires that will be used. Number of wires: ___________ Identify the outer diameter (OD) of those wire(s). OD of the wires: ___________ Material Bundled Cable Discrete Wires Shell PC Cable Range Cable Range Wire Outer Connector Wire Outer Connector Sealing Grommet EPDM Number Diameter (OD) Part Kit Number Diameter (OD) Part Kit Flammability UL94 V0 of Wires mm (in) - Numbers - Designation mm (in) Designation of Wires - Numbers - Color Black Minimum Quantity .............. 25 ............................. Minimum Quantity .............. 25 ............................. 2 0.75 to 1.5 PS2T20-2X PM 21 3.0 to 4.5 PS1T20-5X PS 01 1 Torque Requirements (0.03 to 0.06) (0.12 to 0.18) .......................................................................................................... .......................................................................................................... 2 1.5 to 2.6 PM 22 PS1T20-7X PS2T20-3X Hand tighten until snug, using 1 4.5 to 6.5 PS 02 (0.06 to 0.10) (0.18 to 0.26) a wrench tighten an additional .......................................................................................................... .......................................................................................................... 0.75 to 1.5 PM 31 1/4 to 1/2 turn. 3 PS3T20-2X 1 6.5 to 8.5 PS1T20-9X PS 03 (0.03 to 0.06) (0.26 to 0.33) Wrench Size 22 .......................................................................................................... .......................................................................................................... 3 1.6 to 2.6 PS3T20-3X PM 32 8.5 to 10.0 PS1T20-10X PS 04 1 (0.06 to 0.10) (0.33 to 0.39) .......................................................................................................... .......................................................................................................... Mechanical 3 4.0 to 4.8 PS3T20-5X PM 35 1 PS 05 10.0 to 11.5 PS1T20-12X (0.16 to 0.19) Operating Temperature (0.39 to 0.45) -20° to 105°C -4° to 221°F www.andersonpower.com All Data Subject To Change Without Notice Step 3: Select Contacts FAQ Q: What should I consider when selecting the contacts? A: Determine the number of amps (continuous and peak). See temperature charts. Amps (continuous) _______ at ______ volts & Peak Amps ________ for ________ seconds Q: Which contacts are used in each shell? A: Pins are used in SK1-019M03 (male receptacle). Sockets are used in SK6-019M03 (female plug) & SK7-019M03 (female panel mount, jam nut) ® Pin Contacts (PowerMod Series) - (For pre-mate and post-mate contacts for sequencing, contact the factory) Connector Hand Pneumatic Tool Insertion Extraction Kit Tool Tool Die Locator Tool Tool Type AWG mm² ---------------- Part Numbers ---------------- Designation Minimum Quantity ............................. 500 50 Standard Length 7.7 PM1000G1 TM0001 N/A TL0001 PM1002G1 PM1003G1 Pin 24 to 20 0.25 to 0.50 PM16P2024S30 PM16P2024S30-50 P46 Pin 20 to 16 0.50 to 1.30 PM16P1620S30 PM16P1620S30-50 P45 Pin 16 to 14 1.30 to 2.10 PM16P1416S30 PM16P1416S30-50 P44 Pin 12 2.5 PM16P12S30 PM16P12S30-50 P47 ® Socket Contacts (PowerMod Series) Type AWG mm² ---------------- Part Numbers ---------------- Hand Pneumatic Tool Insertion Extraction T ool Tool Die Locator Tool Tool Minimum Quantity .............................. 500 50 Socket 24 to 20 0.25 to 0.50 PM16S2024S32 PM16S2024S32-50 S46 Socket 20 to 16 0.50 to 1.30 PM16S1620S32 PM16S1620S32-50 S45 PM1000G1 TM0001 N/A TL0002 PM1002G1 PM1003G1 Socket 16 to 14 1.30 to 2.10 PM16S1416S32 PM16S1416S32-50 S44 Socket 12 2.5 PM16S12S32 PM16S12S32-50 S47 NOTE: APP tooling is required for UL & CSA compliance. Use of unapproved tools will void the connectors warranty. | TEMPERATURE CHARTS | 3 Pole Mini PL SPEC Pak® 3 Pole Mini PL SPEC Pak® Temperature Rise VS. Current Derating VS. Ambient Temperature All Contacts Energized All Contacts Energized 125 60 50 100 40 30 75 20 50 10 0 25 0 1 3 5 7 9 11 13 15 17 19 21 23 25 0 5 10 15 20 25 Amperes Applied Amperes Applied 12 AWG 14 AWG 16 AWG 12 AWG 14 AWG 16 AWG 18 AWG 20 AWG 18 AWG 20 AWG All Data Subject To Change Without Notice www.andersonpower.com Temperature (°C) Ambient Temperature (°C) | CONNECTOR KIT - PART NUMBER CONFIGURATOR | Step 1 Step 2 Step 3 Select Shell Select Sealing Gland Select contact Wire Housing & Insert 1 1 2 Protection Series Color Shell Style Shell Size Arrangement Contacts Arrangement S K 1 - 019 M03 PS 01 - P46 1 = Male, Receptacle (Pins) P46 = 20 - 24 AWG Pin 6 = Female Plug (Sockets) P45 = 16 - 20 AWG Pin 7 = Female Panel Mount Jam P44 = 14 -16 AWG Pin Nut (Sockets) P47 = 12 AWG Pin 019 M03 00 = No Wire Protection S46 = 20 - 24 AWG Socket PS = Plastic Single Hole S45 = 16 - 20 AWG Socket PM = Plastic Multi-Hole S44 = 14 - 16 AWG Socket 00 = No Wire Protection S47 = 12 AWG Socket 01 thru 99 = See page 3 for selection 1 2 See page 2 for more informaton | See page 3 for more information | ACCESSORIES (optional) | Wire Seal Accessories for use with SK7-021M03 Covers Description -------- Part Numbers -------- Description - Part Numbers - Minimum Quantity 1 50 Minimum Quantity ........... 25 Wire Seal Retainer 2-8702P1 - Female Cover SK9F-019 Grommet, wire range 1.2 - 1.9mm (0.047”- 0.075”) OD, Orange 114916P1 114916P1-50 Male Cover SK9M-019 Grommet, wire range 1.9 - 2.4mm (0.75”- 0.090”) OD, Yellow 114916P2 114916P2-50 Grommet, wire range 2.5 - 3.2mm (0.100”- 0.130”) OD, Tan 114916P3 114916P3-50 Sealing Plug 114916P4 114916P4-50 | DIMENSIONS | Male Receptacle Female Plug Female Panel Mount SK1-019M03 SK6-019M03 SK7-019M03 SK1-019M03 & SK6-019M03 (mated) [ 0.71 ] [ 0.71 ] [ 0.89 ] Ø 18.2 Ø 18.2 Ø 22.6 [ 3.6 ] [ 1.68 ] 91 [ 1.54 ] 42.7 PANEL 39.2 [ 0.43 ] [ 0.94 ] 10.9 23.8 Male Cover Female Cover SK1-019M03 & SK7-019M03 (mated) SK9M-019 SK9F-019 [ 0.81 ] 20.5 PANEL [ 0.70 ] Ø 17.9 [ 0.71 ] Ø 18 [ 2.5 ] [ 0.91 ] 64 23.1 All Data Subject To Change Without Notice 2018-0032 DS-MINI3PL REV 04 © 2018 Anderson Power Products, Inc. All rights reserved. APP®, Anderson Power Products®, PowerMod®, SPEC Pak® and the APP Logo are registered trademarks of Anderson Power Products, Inc. ® ® HEADQUARTERS: Anderson Power Products , 13 Pratts Junction Road, Sterling, MA 01564-2305 USA T:978-422-3600 F:978-422-0128 • EUROPE: Anderson Power Products Ltd., Unit 3, Europa Court, Europa Boulevard, Westbrook, Warrington, Cheshire, WA5 7TN United Kingdom T: +44 (0) 1925 428390 F: +44 (0) 1925 520203 • ASIA / PACIFIC: IDEAL Anderson Asia Pacific Ltd., Unit 922-928 Topsail Plaza, 11 On Sum Street, Shatin N.T., Hong Kong T:+(852) 2636 0836 F:+(852) 2635 9036 • CHINA: IDEAL Anderson Technologies (Shenzhen) Ltd., Block A8 Tantou Western Industrial Park, Songgang Baoan District, Shenzhen, PR. China 518105 T: +(86) 755 2768 2118 F: +(86) 755 2768 2218 • TAIWAN: IDEAL Anderson Asia Pacific Ltd., Taiwan Branch, 4F.-2, No.116, Dadun 20th St., Situn District, Taichung City 407, Taiwan (R.O.C.) T: +(886) 4 2310 6451 F:+(886) 4 2310 6460 • www.andersonpower.com