POWER DS1100TDC Data Sheet 1100 Watts Distributed Power System Front-end Bulk Power Total Output Power: 1100 W continuous Wide Input Voltage: -40 to -72 Vdc SPECIAL FEATURES ƒ 1100 W output power ƒ High-power and short form factor ƒ 1U power supply 3 ƒ High density design: 26 W/in Electrical Specifications ƒ Inrush current control Input ƒ N+1 or N+N Redundant Input range -40 to -72 Vdc ƒ Hot-pluggable ƒ Active current sharing Efficiency 90.0% typical ƒ Full digital control Max input current 37.0 Arms ƒ PMBus compliant Inrush current ETSI EN 300 132-2 Limits ƒ Compatible with Artesyn’s Universal Conducted EMI Class A +6 dB margin PMBus GUI Radiated EMI Class A +6 dB margin ƒ Reverse airflow option Hold-up time 1 ms at full load ƒ Two-year warranty Output Main DC Output Standby DC Output COMPLIANCE MIN NOM MAX MIN NOM MAX ƒ EMI Conducted/Radiated Class A Limits + 6 dB margin Nominal setting -1% 12 +1% -2.5% 3.3 2.5% ƒ EN61000-4 Electro-magnetic Total output regulation range 11.4 V 12 12.6 V 3.14 V 3.3 3.46 V Compatibility Dynamic load regulation range 11.4 V 12.6 V 3.14 V 3.46 V ƒ RoHS 6/6 Output ripple 180 mVp-p 45 mVp-p 1 Output current 0.5 A 91.6 A 0.1 A 3.0 A SAFETY Current sharing Within ±5.625A of each other from N/A ƒ UL/cUL 60950 25% to 100% load ƒ DEMKO+ CB Report Capacitive loading 500 µF 11,000 µF 100 µF 680 µF ƒ CE Mark Start-up from AC to output 3000 ms 2500 ms ƒ China CCC Output rise time 5 100 ms 100 ms Note: Outputs shall be isolated from the chassis ground by at least 50 V 1 Minimum starting current for transient load response testing only. Unit is designed to operate and be within output regulation at zero load. DS1100TDC Data Sheet Electrical Specifications Protections Main Output MIN NOM MAX 2 Overcurrent protection 107% 130% 1 Overvoltage protection 13.5 V 14.5 V Overtemperature protection Yes, autorecovery Fan fault protection Yes Standby Output 3 Overcurrent protection 107% 150% 1 Over-oltage protection 3.6 V 4.1V 1 Latch mode 2 Autorecovery for 5s then latch 3 Autorecovery Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK PSKILL_H First break/last mate active HIGH signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 100 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 200 mV. 2 I C Addressing Ordering Information A1 Pin A0 Pin PMBus (w/r) Model Number Nominal Main Output Standby Output Airflow Direction 0 0 B0/B1 DS1100TDC-3 12 V 3.3 V @ 3 A Std (forward) 0 1 B2/B3 DS1100TDC-3-001 12 V 3.3 V @ 3 A Reverse 1 0 B4/B5 1 1 B6/B7 * For additional addressing options, please contact techsupport DS1100TDC Data Sheet Control and Status Signals Output Signals INPUT_OK Signal used to indicate the presence of DC input to the power supply. A logic level HIGH will indicate that the DC input to the power supply is within the operating range while a logic level LOW will indicate that input has been lost. This is an open collector/drain output. This pin is pulled high by a 1 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 200 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Output high voltage 2.4 V 3.6 V OH V Output low voltage 0.4 V OL I Output signal source current 2 mA SOURCE I Output signal sink current 4 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of DC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Output high voltage 2.4 V 3.6 V OH V Output low voltage 0.4 V OL I Output signal source current 2 mA SOURCE I Output signal sink current 4 mA SINK Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is connected via a 220 ohm resistor to the standby return in the power supply. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX V Output high voltage 2.4 V 3.6 V OH V Output low voltage 0.4 V OL I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK DS1100TDC Data Sheet Control and Status Signals BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Input logic level LOW 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 1.0 I Current that may be sourced by this pin 4.0 mA SOURCE SCL, SDA 2 Clock and data signals defined as per I C requirements. These pins are pulled high internally to 3.3V by a 100kohm resistor. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 200 pF decoupling capacitor at the system side. VL Input logic level LOW 0.8 V VH Input logic level HIGH 2.0 V 3.6 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. Electrical Specifications LED Indicators Two LEDs are used to indicate the power supply status. Input LED Fail LED Color Green Amber/Green No input to PSU Off Off Input present, STBY ON, main output OFF On Blinking Amber, at least 1 Hz Main output ON On Green Power supply warning (hi-temp) On Blinking Amber/Green, at 2:1 ratio, at least 1 Hz Power supply warning (slow fan) On Blinking Amber/Green, at 1:1 ratio, at least 1 Hz Power supply failure (OVP, OTP, FAN FAULT) On Amber Firmware Reporting And Monitoring Accuracy Range Output loading 5% to 20% 20% to 50% 50% to 100% Input voltage ±5% Input current ±0.55 A fixed error ±4% Input power ±5 W fixed error up to 120 W input ±4% Output voltage ±2% Output current ±0.8 A fixed error ±5% ±2% Temperature ±5 °C across operating range Fan speed ±250 RPM PMBus YES Remote ON/OFF YES DS1100TDC Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from input being applied to standby output being within regulation 2500 ms sb_On T Delay from input being applied to INPUT_OK assertion 1500 ms INPUT_OK_ON T Delay from standby output to main output voltage being within regulation 1000 ms sb_Vout T Delay from input being applied to main output being within regulation 3000 ms INPUT_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWOK_On T Delay from loss of input to assertion of INPUT_OK 20 ms INPUT_OK_Delay T Delay from loss of input to deassertion of PWOK PWOK may deassert as soon as input loss is detected ms PWOK_Hold-up T Delay from loss of input to main output falling out of regulation 1 ms Vout_Hold-up T Delay from loss of input to standby output falling out of regulation 25 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 700 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 400 ms PSON_On_Delay Timing Diagram DC Input T sb_Hold-up T sb_On T Input_Delay Vout_stby T sb_Vout T INPUT_OK_ON INPUT_OK T Input_On_Delay T PWOK_Off Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1100TDC Data Sheet Mechanical Outline P/N: 531-002961-0000 100 MODEL LABEL (11.94) 4.32 0.5 329.18 0.5 54.6 0.4 321.56 0.4 GREEN LED WHITE LED 9.05 0.4 DS1100TDC-3 (FORWARD) - RED HANDLE DS1100TDC-3-001 (REVERSE) - BLUE HANDLE AIRFLOW DIRECTION DS1100TDC-3 FORWARD AIRFLOW DS1100TDC-3-001 REVERSE AIRFLOW Output Connector Pin Configuration Input and Output Connectors A1 3.3 VSB Standby Output Output Connector Part Number TEI 1926736-3 B1 3.3 VSB Standby Output Output Mating Connector Part TEI 2-1926739-5, 1892787-6 or Number equivalent C1 3.3 VSB Standby Output Input Mating Connector Part Molex 42816-0212 or equivalent D1 3.3 VSB Standby Output Number E1 3.3 VSB Standby Output A2 SGND Signal Ground B2 SGND Signal Ground C2 Reserved D2 Reserved E2 Reserved A3 A2/ A_Select Optional address line 2 B3 A0 I C address 2 C3 SDA I C Data D3 -Remote_Sense Wire drop compensation E3 +Remote_Sense Wire drop compensation 2 A4 SCL I C Clock B4 PSON_L Enable/Inhibit C4 PS_INTERRUPT_L Alert for failure 2 D4 A1 I C address E4 INPUT_OK Input indicator A5 PSKILL_H First break/last mate pin B5 ISHARE Current share bus C5 PWOK Output indicator D5 Reserved E5 PS_PRESENT_L power supply present P1-P5 +12 V Return Main output power contact P6-P10 12 V Main output return contact +0.64 40 -0.50 3.6 0.4 10.4 DS1100TDC Data Sheet Environmental Specifications Operating temperature DS1100TDC-3: Full power at -5 to 50 °C, derate to 660 W at 65 °C DS1100TDC-3-001: Full power at -5 to 45 °C, derate to 660 W at 55 °C Operating altitude up to 10,000 feet Operating relative humidity +5% to +95% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity +5% to +95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating random shock and vibration RoHS compliance Yes MTBF >300,000 hours. Operating life Minimum of 7 years at typical operating conditions Reliability All electronic component derating analysis and capacitor life calculation is done at 40 °C ambient, 80% of maximum rated load, nominal input line voltage. WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1100TDC DS 18Sep2015