POWER PTH03010 Data Sheet 3.3 Vin Single Output Total Power: 37.5 Watts Input Voltage: 2.95 - 3.65 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 15 A output current ƒ 3.3 V input voltage ƒ Wide-output voltage adjust (0.8 V - 2.5 V) ™ ƒ Auto-track sequencing* Electrical Specifications ƒ Margin up/down controls ƒ Pre-bias start-up capability Input ƒ Efficiencies up to 93% Input voltage ra nge (See Note 3) 2.95 - 3.65 V ƒ Output ON/OFF inhibit Input current No load 10 mA typical ƒ Output voltage sense Remote ON/OFF (See Note 1) Positive logic ƒ Point-of-Load-Alliance (POLA) Start-up time 1 V/ms compatible Undervoltage lockout 2.8 - 2.95 V typical ƒ RoHS compliant Track input voltage Pin 8 (See Note 6, 7) ±0.3 Vin ƒ Two year warranty Output Voltage adjustability (See Note 4) 0.8 - 2.5 Vdc SAFETY Setpoint accuracy ±2.0% Vo ƒ UL/cUL CAN/CSA-C22.2 No. 60950-1-03 Line regulation ±10 mV tpical Load regulation ±12 mV typical ƒ UL 60950-1 File No. E174104 ƒ TÜV Product Service (EN60950) Total regulation ±3.0% Vo Certificate No. B04 06 38572 044 Minimum load 0 A ƒ CB report and certificate to Ripple and noise 20 MHz bandwidth 20 mV pk-pk IEC60950, Certificate No. US/8292/ Temperature co-efficient -40 °C to +85 °C ±0.5% Vo UL Transient response (See Note 5) 70 μs recovery time Overshoot/undershoot 100 mV Margin adjustment ±5.0% Vo All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Cin = 470 μF, Cout = 0 μF. *Auto-track is a trademark of Texas Instruments. PTH03010 Data Sheet EMC Characteristics General Specifications Electrostatic discharge EN61000-4-2, IBC801-2 Efficiency (See Efficiency Table) 93% max. Conducted immunity EN61000-4-6 Insulation voltage Non-isolated Radiated immunity EN61000-4-3 Switching frequency Fixed 300 kHz typ. ±25 kHz Approvals and EN60950, UL/cUL60950 standards Environmental Specifications Material flammability UL94V-0 Thermal performance Operating ambient temperature -40 °C to +85 °C (See Note 2) Dimensions L x W x H 34.80 x 15.75 x 9.00 mm 1.370 x 0.620 x .354 in Non-operating temperature -40 °C to +125 °C Weight 5 g (0.18 oz) MSL (‘Z’ suffix only) JEDEC J-STD-020C Level 3 MTBF Telcordia SR-332 7,092,000 hours Protection Short-circuit Auto reset 27.5 A typical Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (9) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load PTH03010 37.5 W 2.95 - 3.65 V 0.8 - 2.5 V 0 A 15 A 93% ±10 mV ±12 mV Part Number System with Options Product Family Input Voltage Mechanical Output Voltage Pin Option Mounting Options Pin Option Output Current Package Code PTH 03 01 0 W A S T No Suffix = Trays Point-of-Load 03 = 3.3 V 01 = 15 A Always 0 W = Wide D = Horizontal through- (8) Alliance compatible hole (Matte Sn) T = Tape and Reel Z = Surface-mount (96.5/3.0/0.5 Sn/Ag/Cu pin solder material Notes: Output Voltage Adjustment 1. Remote ON/OFF. Positive Logic ON: Pin 3 open; or V > Vin - 0.5 V The ultra-wide output voltage trim range offers major advantages to users who OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). select the PTH03010. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be 2. See Figures 1 and 2 for safe operating curves. trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTH03010 converter 3. A 470 μF electrolytic input capacitor is required for proper operation. The capacitor must be leaves the factory the output has been adjusted to the default voltage of 0.8 V. rated for a minimum of 700 mA rms of ripple current. 4. An external output capacitor is not required for basic operation. Adding 330 μF of distributed capacitance at the load will improve the transient response. Efficiency Table (Io = 10A) 5. 1 A/μs load step, 50 to 100% Iomax, Cout = 330 μF. Output Voltage Efficiency 6. If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). Vo = 1.0 V 85% 7. The pre-bias start-up feature is not compatible with Auto-Track™. This is because when the module is under Auto-Track™ control, it is fully active and will sink current if the output voltage Vo = 1.2 V 87% is below that of a back-feeding source. Therefore to ensure a pre-bias hold-off, one of the Vo = 1.5 V 89% following two techniques must be followed when input power is first applied to the module. The Vo = 1.8 V 91% Auto-Track™ function must either be disabled, or the module’s output held off using the Inhibit pin. Refer to Application Note 150 for more details. Vo = 2.0 V 92% 8. Tape and reel packaging only available on the surface-mount versions. Vo = 2.5 V 93% 9. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. PTH03010 Data Sheet 90 90 80 80 70 70 60 60 400 LFM 400 LFM 200 LFM 200 LFM 50 50 100 LFM 100 LFM Nat conv Nat conv 40 40 30 30 20 20 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 2 - Safe Operating Area Figure 1 - Safe Operating Area Vin = 3.3 V, Output Voltage = 1.0 V (See Note A) Vin = 3.3 V, Output Voltage = 2.5 V (See Note A) Track Margin Down Margin Up 100 10 9 8 90 1 7 Vout 2.5V PTH03010 80 2.0V (Top View) Vout 1.8V Vin 2 6 70 1.5V 1.2V 3 4 5 1.0V Vo Sense 60 Inhibit L 50 + + O C in 470µF A (Required) R SET 0.5%, 0.1W D (Required) C out 330µF 40 (Optional) 012 3 45678 9 10 11 12 13 14 15 GND GND OUTPUT CURRENT (A) Figure 3 - Eciency vs Load Current Figure 4 - Standard Application Vin = 3.3 V (See Note B) Notes: A. SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. B. Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the converter. File Name: pth03010.pdf Rev (06): 16 Dec 2005 EFFICIENCY (%) TEMPERATURE (ºC) TEMPERATURE (ºC) PTH03010 Data Sheet Mechanical Drawings Plated through-hole 1.370 (34.80) 0.140 Pin Assignments 0.125 (3.18) (3.55) 0.125 (3.18) 0.060 Pin Function 0.060 0.375 (1.52) 0.625 (15.88) ø0.040 (1.02) 1 Ground (1.52) (9.52) 5 Places 2 Vin 1 10 9 8 7 3 Inhibit* 4 Vo adjust 0.070 (1.78) 0.620 (Stando Shoulder) 5 Vo sense 0.500 (15.75) (12.70) 6 Vout Lowest Component 7 Ground 0.010 min. (0.25) 8 Track Bottom side Clearance 2 4 5 6 3 9 Margin down* 10 Margin up* TOP VIEW *Denotes negative logic: Host Board Open = Normal operation Ground = Function active 0.354 (9.00) MAX. Dimensions in Inches (mm) Tolerances (unless otherwise specied) 2 Places ±0.030 (±0.76) SIDE VIEW 3 Places ±0.010 (±0.25) Surface-mount 1.370 (34.80) 0.125 (3.18) 0.125 (3.18) *After solder reow 0.060 0.354 (9.00) on customer board 0.375 0.060 (1.52) 0.625 (15.88) max.* (9.52) (1.52) 1 10 9 8 7 Solder Ball ø0.040 (1.02) 10 Places 0.620 0.500 (15.75) (12.70) 2 3 5 6 4 TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specied) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. PTH03010 22Apr2015