POWER PTH05020 Data Sheet 5 Vin Single Output Total Power: 79.2 Watts # of Outputs: Single SPECIAL FEATURES ƒ 22 A output current ƒ 5 V input voltage ƒ Wide-output voltage adjust (0.8 V - 3.6 V) ™ ƒ Auto-track sequencing* Electrical Specifications ƒ Margin up/down controls ƒ Pre-bias start-up capability Input ƒ Efficiencies up to 96% Input voltage ra nge (See Note 3) 4.5 - 5.5 Vdc ƒ Output ON/OFF inhibit Input current No load 10 mA typical ƒ Output voltage sense Remote ON/OFF (See Note 1) Positive logic ƒ Point-of-Load-Alliance (POLA) Undervoltage lockout 3.7 - 4.3 V typical compatible Track input voltage Pin 8 (See Note 6 & 7) ±0.3 Vin ƒ RoHS compliant Output ƒ Two year warranty Voltage adjustability (See Note 4) 0.8 - 3.6 Vdc Setpoint accuracy ±2.0% Vo SAFETY Line regulation ±5 mV typical ƒ UL/cUL CAN/CSA-C22.2 No. Load regulation ±5 mV typical 60950-1-03/UL 60950-1, File No. E174104 Total regulation ±3.0% Vo ƒ TÜV Product Service (EN60950) Minimum load 0 A Certificate No. B04 06 38572 044 Ripple and noise 20 MHz bandwidth 20 mV pk-pk ƒ CB report and certificate to Temperature co-efficient -40 °C to +85 °C ±0.5% Vo IEC60950, Certificate No. US/8292/ Transient response (See Note 5) 70 μs recovery time UL Overshoot/undershoot 120 mV Margin adjustment ±5.0% Vo All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Cin = 1000 μF, Cout = 0 μF. *Auto-track is a trademark of Texas Instruments. PTH05020 Data Sheet EMC Characteristics General Specifications Electrostatic discharge EN61000-4-2, IEC801-2 Efficiency (See Efficiency Table) 96% max. Conducted immunity EN61000-4-6 Insulation voltage Non-isolated Radiated immunity EN61000-4-3 Switching frequency 250 - 340 kHz Approvals and EN60950, UL/cUL60950 standards Environmental Specifications Material flammability UL94V-0 Thermal performance Operating ambient temperature -40 °C to +85 °C (See Note 2) Non-operating temperature -40 °C to +125 °C Dimensions L x W x H 37.97 x 22.10 x 9.00 mm 1.495 x 0.870 x 0.354 in MSL (‘Z’ suffix only) JEDEC J-STD-020C Level 3 Weight 7 g (.25 oz) Protection MTBF Telcordia SR-332 5,236,000 hours Short-circuit Auto reset 41 A typical Thermal Auto recovery Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (9) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load PTH05020 79.2 W 4.5 - 5.5 Vdc 0.8 - 3.6 V 0 A 22 A 96% ±5 mV ±5 mV Part Number System with Options Product Family Input Voltage Output Current Mechanical Output Voltage Pin Option Mounting Options Pin Option Package Code PTH 05 02 0 W A S T Point-of-Load 05 = 5 V 02 = 22 A Always 0 W = Wide D = Horizontal through- No Suffix = Trays (8) Alliance compatible hole (Matte Sn) T = Tape and Reel Z = Surface-mount (96.5/3.0/0.5 Sn/Ag/Cu pin solder material Notes: Output Voltage Adjustment 1. Remote ON/OFF. Positive Logic The ultra-wide output voltage trim range offers major advantages to users who ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). select the PTH05020. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be 2. See Figures 1 for safe operating curves. trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTH05020 converter 3. A 1000 μF electrolytic input capacitor is required for proper operation. The capacitor must be leaves the factory the output has been adjusted to the default voltage of 0.8 V. rated for a minimum of 700 mA rms of ripple current. 4. An external output capacitor is not required for basic operation. Adding 330 μF of distributed capacitance at the load will improve the transient response. Efficiency Table (Io = 10 A) 5. 1 A/μs load step, 50 to 100% Iomax, Cout = 330 μF. Output Voltage Efficiency 6. If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). Vo = 1.0 V 88% 7. The pre-bias start-up feature is not compatible with Auto-Track™. This is because when the module is under Auto-Track™ control, it is fully active and will sink current if the output voltage Vo = 1.2 V 90% is below that of a back-feeding source. Therefore to ensure a pre-bias hold-off, one of the Vo = 1.5 V 91% following two techniques must be followed when input power is first applied to the module. The Vo = 1.8 V 92% Auto-Track™ function must either be disabled, or the module’s output held off using the Inhibit pin. Refer to Application Note 156 for more details. Vo = 2.0 V 93% 8. Tape and reel packaging only available on the surface-mount versions. Vo = 2.5 V 94% 9. NOTICE: Some models do not support all options. Please contact your local Artesyn Vo = 3.3 V 96% representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. PTH05020 Data Sheet 90 80 100 70 90 3.3V 80 2.5V 60 Nat conv 1.8V 100 LFM 1.5V 70 50 200 LFM 1.2V 400 LFM 1.0V 60 40 50 30 40 20 0 2 4 6 8 10 12 14 16 18 20 22 0 2 46 8 10 12 14 16 18 20 22 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 1 - Safe Operating Area Figure 2 - Eciency vs Load Current Vin = 5 V, Output Voltage = 3.3 V (See Note A) Vin = 5 V (See Note B) Track Margin Down Margin Up 10 9 8 1 7 PTH05020 (Top View) Vout Vin 2 6 3 4 5 Vo Sense Inhibit L + C in 1000µF + O R SET 1%, 0.1W C out 330µF A (Required) (Required) D (Optional) GND GND Figure 3 - Standard Application Notes: A. SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. B. Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the converter. File Name: pth05020.pdf Rev (07): 16 Dec 2005 TEMPERATURE (ºC) EFFICIENCY (%) PTH05020 Data Sheet Mechanical Drawings Plated through-hole 1.495 (37.97) 0.125 (3.18) 0.140 Pin Assignments (3.55) 0.125 (3.18) 0.060 Pin Function 0.060 (1.52) 0.500 0.625 (15.88) (1.52) ø0.040 (1.02) (12.70) 1 Ground 10 Places 2 Vin 1 10 9 8 7 3 Inhibit* 4 Vo adjust (0.070 (1.78) (Stando Shoulder) 5 Vo sense 0.750 0.870 (19.05) (22.10) 6 Vout 7 Ground Lowest Component 0.010 min. (0.25) 8 Track Bottom side Clearance 4 5 3 9 Margin down* 2 6 10 Margin up* Host Board TOP VIEW *Denotes negative logic: Open = Normal operation Ground = Function active 0.354 (9.00)max. Side View Dimensions in Inches (mm) Tolerances (unless otherwise specied) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Surface-mount 1.495 (37.97) 0.125 (3.18) 0.125 (3.18) *After solder reow 0.060 0.354 (9.00) 0.060 0.500 0.625 (15.88) (1.52) on customer board max.* (1.52) (12.70) 1 10 9 8 7 Solder Ball ø0.040 (1.02) 10 Places 0.870 0.750 (22.10) (19.05) 3 4 5 2 6 TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specied) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. PTH05020 23Jun2015