POWER PTH12020 Data Sheet 12 Vin Single Output Total Power: 99 Watts # of Outputs: Single SPECIAL FEATURES ƒ 18 A output current ƒ 12 V input voltage ƒ Wide-output voltage adjust: 1.2 - 5.5 Vdc for suffix ‘W’ 0.8 - 1.8 Vdc for suffix ‘L’ ™ ƒ Auto-track sequencing* Electrical Specifications ƒ Margin up/down controls Input ƒ Efficiencies up to 95% Input voltage ra nge (See Note 3) 10.8 - 13.2 Vdc ƒ Output ON/OFF inhibit Input current No load 10 mA typical ƒ Output voltage sense Remote ON/OFF (See Note 1) Positive logic ƒ Point-of-Load-Alliance (POLA) Start-up time 1 V/ms compatible Undervoltage lockout 9.2 - 9.7 V typical ƒ RoHS compliant Track input voltage Pin 8 (See Notes 6 ) ±0.3 Vin ƒ Two year warranty Output Voltage adjustability (See Note 4) 1.2 - 5.5 Vdc (Suffix ‘W’) SAFETY 0.8 - 1.8 Vdc (Suffix ‘L’) ƒ UL/cUL CAN/CSA-C22.2 No. Setpoint accuracy ±2.0% Vo 60950-1-03/UL 60950-1 Line regulation ±5 mV typical ƒ TÜV Product Service (EN60950) Load regulation ±5 mV typical ƒ CB Report and Certificate to Total regulation ±3.0% Vo IEC60950 Minimum load 0 A Ripple and noise 20 MHz bandwidth 32 mV pk-pk (Suffix ‘W’) 1% Vo (Suffix ‘L’) Temperature co-efficient -40 °C to +85 °C ±0.5% Vo Transient response (See Note 5) 70 μs recovery time Overshoot/undershoot 130 mV Margin adjustment ±5.0% Vo All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Cin = 560 μF, Cout = 0 μF. *Auto-track is a trademark of Texas Instruments. PTH12020 Data Sheet EMC Characteristics General Specifications Electrostatic discharge EN61000-4-2, IEC801-2 Efficiency See Efficiency Table Conducted immunity EN61000-4-6 Insulation voltage Non-isolated Radiated immunity EN61000-4-3 Switching frequency Suffix ‘W’ 260 - 380kHz Suffix ‘L’ 200 - 300 kHz Environmental Specifications Approvals and EN60950, UL/cUL60950 standards Thermal performance Operating ambient temperature -40 °C to +85 °C (See Note 2) Non-operating temperature -40 °C to +125 °C Material flammability UL94V-0 MSL (‘Z’ suffix only) JEDEC J-STD-020C Level 3 Dimensions L x W x H 37.97 x 22.10 x 9.00 mm 1.495 x 0.870 x 0.354 in Protection Weight 7 g (0.25 oz) Short-circuit Auto reset 30 A typical MTBF Telcordia SR-332 5,236,000 hours Thermal Auto recovery Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (8) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load PTH12020L 99 W 10.8 - 13.2 Vdc 0.8 - 1.8 Vdc 0 A 18 A 89% ±5 mV ±5 mV PTH12020W 99 W 10.8 - 13.2 Vdc 1.2 - 5.5 Vdc 0 A 18 A 95% ±5 mV ±5 mV Part Number System with Options (8) Pin Option Product Family Input Voltage Output Current Mechanical Output Voltage Pin Option Mounting Options Package Code PTH 12 02 0 W A S T 02 = 18 A Point-of-Load 12 = 12 V Always 0 W = Wide D = Horizontal No Suffix = Trays (8) Alliance compatible L = Low Voltage through-hole (RoHS T = Tape and Reel 6/6) Z = Surface-mount solder ball (RoHS 6/6) Notes: Output Voltage Adjustment 1. Remote ON/OFF. Positive Logic The ultra-wide output voltage trim range offers major advantages to users who ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). select the PTH12020. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be 2. See Figures 1, 2 and 3 for safe operating curves. trimmed in a range of 1.2 - 5.5 Vdc. When the PTH12020 converter leaves the 3. A 560 μF electrolytic input capacitor is required for proper operation. The capacitor must be factory the output has been adjusted to the default voltage of 1.2 V. rated for a minimum of 800 mA rms of ripple current. 4. An external output capacitor is not required for basic operation. Adding 330 μF of distributed capacitance at the load will improve the transient response. Efficiency Table: PTH12020W Efficiency Table: PTH12020L 5. 1 A/μs load step, 50 to 100% Iomax, Cout = 330 μF. (Io = 18 A) (Io = 18 A) 6. If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). Output Voltage Efficiency Output Voltage Efficiency 7. Tape and reel packaging only available on the surface-mount versions. Vo = 5.0 V 95% Vo = 1.8 V 89% 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Vo = 3.3 V 93% Vo = 1.5 V 87% representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. Vo = 2.5 V 92% Vo = 1.2 V 85% Vo = 1.8 V 90% Vo = 1.0 V 83% Vo = 1.5 V 88% Vo = 0.8 V 80% Vo = 1.2 V 86% PTH12020 Data Sheet PTH12020W Characteristic Data 90 90 80 80 70 70 60 60 Nat Conv Nat Conv 100 LFM 100 LFM 50 50 200 LFM 200 LFM 400 LFM 400 LFM 40 40 30 30 20 20 0 2 4 6 8 10 12 14 1 6 18 0 2 4 6 8 10 12 14 1 6 18 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 1 - Safe Operating Area Figure 2 - Safe Operating Area Vin = 12 V, Output Voltage = 5 V (See Note A) Vin = 12 V, Output Voltage = 3.3 V (See Note A) 90 100 80 90 70 Vout 80 5.0V 3.3V 60 Nat Conv 2.5V 70 100 LFM 1.8V 50 200 LFM 1.5V 400 LFM 60 1.2V 40 50 30 40 20 0 2 4 6 8 10 12 14 16 18 0 2 4 6 8 10 12 14 1 6 18 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 3 - Safe Operating Area Figure 4 - Eciency vs Load Current Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A) Vin = 12 V (See Note B) Notes: Track Margin Down A. SOA curves represent the conditions at which internal components are within the Artesyn derating Margin Up guidelines. B. Characteristic data has been developed from actual products tested at 25 °C. This data is 10 9 8 considered typical data for the converter. 1 7 PTH12020 (Top View) Vout Vin 6 2 5 4 3 Vo Sense Inhibit L + Cin 560F + O RSET 1%, 0.1W Cout 330F A (Required) (Required) (Optional) D GND GND Figure 5 - Standard Application TEMPERATURE (ºC) TEMPERATURE (ºC) EFFICIENCY (%) TEMPERATURE (ºC) PTH12020 Data Sheet PTH12020L Characteristic Data 100 90 80 90 70 Vout 80 1.8V 60 Nat Conv 1.5V 100 LFM 1.2V 50 200 LFM 70 1.0V 400 LFM 0.8V 40 30 60 20 50 0 3 6 9 12 15 18 0 369 1 2 15 18 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 6 - Safe Operating Area for PTH12020L Figure 7 - Eciency vs Load Current for PTH12020L Vin = 12 V (See Note B) Vin = 12 V, Output Voltage = 1.8 V (See Note A) Track Notes: Margin Down A. SOA curves represent the conditions at which internal components are within the Artesyn derating Margin Up guidelines. B. Characteristic data has been developed from actual products tested at 25 °C. This data is 10 9 8 considered typical data for the converter. 1 7 PTH12020 (Top View) Vout Vin 2 6 5 4 3 Vo Sense Inhibit L + Cin 560F + O RSET 1%, 0.1W Cout 330F A (Required) (Required) (Optional) D GND GND Figure 8 - Standard Application TEMPERATURE (ºC) EFFICIENCY (%) PTH12020 Data Sheet Mechanical Drawings Plated through-hole 1.495 (37.97) 0.125 (3.18) 0.140 Pin Assignments (3.55) 0.125 (3.18) 0.060 Pin Function 0.060 0.500 (1.52) 0.625 (15.88) (1.52) 1 Ground ø0.040 (1.02) (12.70) 10 Places 2 Vin 10 9 1 8 7 3 Inhibit* 4 Vo adjust (0.070 (1.78) 5 Vo sense (Stando Shoulder) 0.750 0.870 6 Vout (22.10) (19.05) 7 Ground Lowest Component 8 Track 0.010 min. (0.25) 9 Margin down* Bottom side Clearance 4 5 3 2 6 10 Margin up* *Denotes negative logic: Host Board TOP VIEW Open = Normal operation Ground = Function active 0.354 (9.00)max. Side View Dimensions in Inches (mm) Tolerances (unless othe rwise specied) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Surface-mount 1.495 (37.97) 0.125 (3.18) 0.125 (3.18) 0.060 *After solder reow 0.354 (9.00) 0.060 0.500 0.625 (15.88) (1.52) on customer board max.* (1.52) (12.70) 1 10 9 8 7 Solder Ball ø0.040 (1.02) 10 Places 0.870 0.750 (22.10) (19.05) 3 4 5 2 6 TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless othe rwise specied) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. PTH12020 06Dec2016