POWER PTH12030 Data Sheet 12 Vin Single Output Total Power: 143 Watts # of Outputs: Single SPECIAL FEATURES ƒ 26 A output current ƒ 12 V input voltage ƒ Wide-output voltage adjust: 1.2 - 5.5 Vdc for suffix ‘W’ 0.8 - 1.8 Vdc for suffix ‘L’ ™ ƒ Auto-track sequencing* Electrical Specifications ƒ Margin up/down controls Input ƒ Efficiencies up to 94.5% Input voltage ra nge (See Note 3) 10.2 - 13.2 Vdc ƒ Output ON/OFF inhibit Input current No load 10 mA typical ƒ Output voltage sense Remote ON/OFF (See Note 1) Positive logic ƒ Point-of-Load-Alliance (POLA) Start-up time 1 V/ms compatible Undervoltage lockout 8.5 - 9.5 V typical ƒ RoHS compliant Track input voltage Pin 11 (See Notes 6 ) ±0.3 Vin ƒ Two year warranty Output Voltage adjustability (See Note 4) 1.2 - 5.5 Vdc (Suffix ‘W’) SAFETY 0.8 - 1.8 Vdc (Suffix ‘L’) ƒ UL/cUL CAN/CSA-C22.2 No. Setpoint accuracy ±2.0% Vo 60950-1-03/UL 60950-1, File No. Line regulation ±5 mV typical E174104 Load regulation ±5 mV typical ƒ TÜV Product Service (EN60950) Certificate No B 04 06 38572 044 Total regulation ±3.0% Vo ƒ CB Report and Certificate to Minimum load 0 A IEC60950, Certificate No. Ripple and noise 20 MHz bandwidth 25 mV pk-pk (Suffix ‘W’) US/8292/UL (See Note 8) 15 mV pk-pk (Suffix ‘L’) Temperature co-efficient -40 °C to +85 °C ±0.5% Vo Transient response (See Note 5) 50 μs recovery time Overshoot/undershoot 150 mV Margin adjustment ±5.0% Vo All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Cin = 560 μF, Cout = 0 μF. *Auto-track is a trademark of Texas Instruments. PTH12030 Data Sheet EMC Characteristics General Specifications Electrostatic discharge EN61000-4-2, IEC801-2 Efficiency See Efficiency Table Conducted immunity EN61000-4-6 Insulation voltage Non-isolated Radiated immunity EN61000-4-3 Switching frequency Over Vin and Io 575 kHz typ ranges Environmental Specifications Approvals and EN60950, UL/cUL60950 standards Thermal performance Operating ambient temperature -40 °C to +85 °C (See Note 2) Non-operating temperature -40 °C to +125 °C Material flammability UL94V-0 MSL (‘Z’ suffix only) JEDEC J-STD-020C Level 3 Dimensions L x W x H 34.80 x 28.45 x 9.00 mm 1.370 x 1.120 x 0.354 in Protection Weight 7 g (0.25 oz) Short-circuit Auto reset 40 A typical MTBF Telcordia SR-332 2,821,000 hours Thermal Auto recovery Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (8) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load PTH12030L 143 W 10.8 - 13.2 Vdc 0.8 - 1.8 Vdc 0 A 26 A 89% ±5 mV ±5 mV PTH12030W 143 W 10.8 - 13.2 Vdc 1.2 - 5.5 Vdc 0 A 26 A 94.5% ±5 mV ±5 mV Part Number System with Options (8) Pin Option Product Family Input Voltage Output Current Mechanical Output Voltage Pin Option Mounting Options Package Code PTH 12 03 0 W A S T Point-of-Load 12 = 12 V 03 = 26 A Always 0 W = Wide D = Horizontal No Suffix = Trays (8) Alliance compatible L = Low Voltage through-hole (RoHS T = Tape and Reel 6/6) Z = Surface-mount solder ball (RoHS 6/6) Notes: Output Voltage Adjustment 1. Remote ON/OFF. Positive Logic The ultra-wide output voltage trim range offers major advantages to users who ON: Pin 4 open; or V > Vin - 0.5 V OFF: Pin 4 GND; or V < 0.8 V (min - 0.2 V). select the PTH12030. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be 2. See Figure 1 for safe operating curve of the PTH12030W and Figure 4 for safe operating curve trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc of the PTH12030L. for suffix ‘L’. When the PTH12030 converter leaves the factory the output has 3. A 560 μF electrolytic input capacitor is required for proper operation. The capacitor must be been adjusted to the default voltage of 1.2 V for the PTH12030W and 0.8 V for rated for a minimum of 800 mA rms of ripple current. the PTH12030L. 4. An external output capacitor is not required for basic operation. Adding 330 μF of distributed capacitance at the load will improve the transient response. 5. 1 A/μs load step, 50 to 100% Iomax, Cout = 330 μF. Efficiency Table: PTH12030W Efficiency Table: PTH12030L 6. If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). (Io = 18 A) (Io = 18 A) 7. Tape and reel packaging only available on the surface-mount versions. Output Voltage Efficiency Output Voltage Efficiency 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Vo = 5.0 V 94.5% Vo = 1.8 V 89% representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. Vo = 3.3 V 92.7% Vo = 1.5 V 87% Vo = 2.5 V 91.4% Vo = 1.2 V 85% Vo = 2.0V 90.3% Vo = 1.0 V 83% Vo = 1.8 V 89.5% Vo = 0.8 V 80% Vo = 1.5 V 88.2% Vo = 1.2 V 86.2% PTH12030 Data Sheet PTH12030W Characteristic Data 90 80 100 70 60 80 Vout Nat Conv 1.2V 100 LFM 1.8V 50 200 LFM 2.5V 400 LFM 3.3V 60 40 5.0V 30 40 20 0 4 8 12 16 20 24 0 4 8 12 16 20 24 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 2 - Eciency vs Load Current Figure 1 - Safe Operating Area Vin = 12 V, Output Voltage = 3.3 V (See Note A) Vin = 12 V (See Note B) PTH12030L Characteristic Data 100 90 80 90 70 Vout 80 1.8V Nat conv 60 1.5V 100 LFM 1.2V 200 LFM 50 70 1.0V 400 LFM 0.8V 40 60 30 20 50 0 5 10 15 20 25 0 5 10 15 20 25 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 3 - Safe Operating Area Figure 4 - Eciency vs Load Current Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A) Vin = 12 V (See Note B) Track Margin Down Margin Up 13 12 11 1 10 9 V in 2 PTH12030 Vout (Top View) Notes: 8 A. SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. 7 3 B. Characteristic data has been developed from actual products tested at 25 °C. This data is L 4 5 6 O Inhibit considered typical data for the converter. A D Vo Sense + + Cin 560F Cout 330F RSET 0.5%, 0.1W (Required) (Optional) (Required) GND GND Figure 5 - Standard Application - All Models TEMPERATURE (ºC) TEMPERATURE (ºC) EFFICIENCY (%) EFFICIENC Y (%) PTH12030 Data Sheet Mechanical Drawings Plated through-hole 1.370 (34.80) Pin Assignments 0.125 (3.18) Pin Function 0.140 0.125 (3.18) 0.060 (3.55) 0.060 0.500 0.500 1 Ground (1.52 ) (1.52 ) (12.70) (12.70) ø0.040 (1.02 ) 2 Vin 13 Places 3 Ground 10 0.125 (3.18) 13 12 11 4 Inhibit* 1 5 Vo adjust 0.500 0.375 (12.70) 6 Vo sense (9.52 ) Lowest Component 1.12 0 7 Ground 0.010 min. (0.25) (28.45) Bottom side Cl earance 8 Vout 2 9 0.12 5 (3.18) 9 Vout 8 0.375 10 Ground (9.52 ) 0.375 11 Track (0.070 (1.78) (9.52 ) 3 (Stando Shoulder) 12 Margin down* 4 5 6 7 13 Margin up* *Denotes negative logic: TOP VIEW Host Board Open = Normal operation Ground = Function active 0.354 (9.00) Dimensions in Inches (mm) max. Tolerances (unless otherwise specied) 2 Places 0.030 (0.76) SIDE VIEW 3 Places 0.010 (0.25) Surface-mount 1.370 (34.80) 0.125 (3.18) 0.125 (3.18) 0.354 (9.00) *A fter solder reflow 0.060 0.060 0.500 0.500 (1.52) max.* on customer boar d (1.52) (12.70) (12.70) 10 0.125 (3.18) Solder Ball 13 12 11 1 ø0.040 (1.02) 0.500 13 Places 0.375 (12.70) (9.52) 1.120 (28.45) 2 9 0.125 (3.18) 8 0.375 (9.52) 0.375 (9.52) 3 4 5 6 7 TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specied) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. PTH12030 29Jun2015