ARTESYN PTV12010WAD

PTV12010 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 1 • 8 A output current NEW Product • 12 V input voltage • Wide-output voltage adjust • 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’ • Auto-track™ sequencing* • Pre-bias start-up • Efficiencies up to 93% • Output ON/OFF inhibit • Vertical through-hole mounting • Point-of-Load-Alliance (POLA) compatible • Undervoltage lockout • Available RoHS compliant The PTV12010 is a non-isolated dc-dc converter from Artesyn under the Point of Load Alliance (POLA) standard. The vertical mounting option of the PTV12010 module provides performance in less than 20% of the space that is required by alternative solutions. The Auto-Track™ feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including DSP’s, FPGA’s and ASIC’s requiring controlled power-up and power-down. The PTV12010 has an input voltage of 10.8 Vdc to 13.2 Vdc and offers a wide 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’ output voltage range with up to 8 A output current, which 2 YEAR WARRANTY allows for maximum design flexibility and a pathway for future upgrades. All specifications are typical at nominal input, full load at 25 °C unless otherwise stated SPECIFICATIONS C = 100 μF and 10 μF (Ceramic), C = 0 μF in out OUTPUT SPECIFICATIONS EMC CHARACTERISTICS Voltage adjustability Suffix ‘W’ 1.2-5.5 Vdc Electrostatic discharge EN61000-4-2, IEC801-2 (See Note 4) Suffix ‘L’ 0.8-1.8 Vdc Conducted immunity EN61000-4-6 Radiated immunity EN61000-4-3 Setpoint accuracy (See Note 8) ±2.0% Vo GENERAL SPECIFICATIONS Line regulation ±10 mV typ. Efficiency See Tables on page 2 Load regulation ±12 mV typ. Insulation voltage Non-isolated Total regulation (See Note 8) ±3.0% Vo Switching frequency Minimum load 0 A Suffix ‘W’ 250-400 kHz 325 kHz typ. Suffix ‘L’ 200-300 kHz 250 kHz typ. Ripple and noise Suffix ‘W’ 20 mV pk-pk 20 MHz bandwidth Suffix ‘L’ 15 mV pk-pk Approvals and EN60950 standards UL/cUL60950 Temperature co-efficient -40 ºC to +85 ºC ±0.5% Vo Material flammability UL94V-0 Transient response 70 μs recovery time (See Note 5) Overshoot/undershoot 100 mV Dimensions (L x W x H) 22.86 x 8.38 x 10.16 mm 0.90 x 0.330 x 0.400 in Weight 2.6 g (0.09 oz) INPUT SPECIFICATIONS MTBF Telcordia SR-332 5,000,000 hours Input voltage range (See Note 3) 10.8V-13.2 Vdc ENVIRONMENTAL SPECIFICATIONS Input standby current 10 mA typ. Thermal performance Operating ambient, -40 ºC to +85 ºC Remote ON/OFF (See Note 1) Positive logic (See Note 2) temperature Undervoltage lockout (Increasing) 9.5 V typ. Non-operating -40 ºC to +125 ºC Track input current Pin 5 (See Notes 6 and 7) -0.13 mA PROTECTION Overcurrent Auto reset 16 A typ. International Safety Standard Approvals UL/cUL CAN/CSA-C22.2 No. 60950 File No. E174104 *Auto-track™ is a trade mark of Texas Instruments TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL File Name: ptv12010w.pdf Rev (02): 19 Dec 2005 PTV12010 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product OUTPUT OUTPUT OUTPUT REGULATION INPUT OUTPUT EFFICIENCY MODEL POWER CURRENT CURRENT (9,10) VOLTAGE VOLTAGE (MAX.) NUMBER (2) LINE LOAD (MAX.) (MIN.) (MAX.) 15 W 10.8-13.2 Vdc 0.8-1.8 Vdc 0 A 8 A 87% ±10 mV ±12 mV PTV12010L 44 W 10.8-13.2 Vdc 1.2-5.5 Vdc 0 A 8 A 92% ±10 mV ±12 mV PTV12010W Part Number System with Options PTV12010W AH (9) Product Family Mounting Style Point of Load Alliance D = Horizontal Through-Hole (Matte Sn) Compatible H = Horizontal Through-Hole (Sn/Pb) Mounting Version V = Vertical Pin Style A = Through-Hole Std. Pin Length (0.150”) Input Voltage 12 = 12 V Output Voltage Code W = Wide Output Current L = Low Voltage 01 = 8 A Mechanical Package Always 0 O Ou ut tp pu ut t V Vo ollt ta ag ge e A Ad djju us st tm me en nt t o of f t th he e P PT TV V1 12 20 01 10 0 S Se er riie es s The ultra-wide output voltage trim range offers major advantages to users who select the PTV12010. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’. When the PTV12010 converter leaves the factory the output has been adjusted to the default voltage of 1.2 V for the PTV12010W and 0.8 V for PTV12010L. EFFICIENCY TABLE - PTV12010L (I = I ) EFFICIENCY TABLE - PTV12010W (I = I ) O OMAX O OMAX OUTPUT VOLTAGE EFFICIENCY OUTPUT VOLTAGE EFFICIENCY Vo = 1.8 V 87% Vo = 5.0 V 92% Vo = 1.5 V 86% Vo = 3.3 V 90% Vo = 1.2 V 84% Vo = 2.5 V 88% Vo = 1.0 V 81% Vo = 1.8 V 85% Vo = 0.8 V 78% Vo = 1.5 V 83% Vo = 1.2 V 80% N No ot te es s 1 Remote ON/OFF. Positive logic source. Therefore to ensure a pre-bias hold-off, one of the following two ON: Pin 7 open; or V > 2 V techniques must be followed when input power is first applied to the OFF: Pin 7 GND; or V < 0.6 V module. The Auto-Track™ function must either be disabled, or the 2 See Figures 1, 2, 3 and 6 for safe operating curves. module’s output held off using the Inhibit pin. Refer to Application Note 3 A 100 μF electrolytic input capacitor is required for proper operation as 196 for more details. well as a 10 μF high-frequency ceramic capacitor. The electrolytic 8 The set-point voltage tolerance is affected by the tolerance and stability capacitor must be rated for the minimum rms of ripple current. of R . The stated limit is unconditionally met if R has a tolerance of set set 4 An external output capacitor is not required for basic operation. Adding 1% with 100/ºC or better temperature stability. 100 μF of distributed capacitance at the load will improve the transient 9 To order Pb-free (RoHS compatible) through-hole parts replace the response. mounting option ‘H’ with ‘D’, e.g. PTV12010WAD. 5 1 A/μs load step, 50 to 100% I , C3 = 100 μF. omax 10 NOTICE: Some models do not support all options. Please contact your 6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). local Artesyn representative or use the on-line model number search tool at 7 The pre-bias start-up feature is not compatible with Auto-Track™. This is http://www.artesyn.com/powergroup/products.htm to find a suitable because when the module is under Auto-Track™ control, it is fully active alternative. and will sink current if the output voltage is below that of a back-feeding File Name: ptv12010w.pdf Rev (02): 19 Dec 2005 PTV12010 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product PTV12010W Characteristic Data 90 90 80 80 70 70 400 LFM 60 60 200 LFM 400 LFM 100 LFM 200 LFM Nat conv 50 50 100 LFM Nat conv 40 40 30 30 20 20 01 23 4 5 6 78 01 23 4 5 6 7 8 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 2 - Safe Operating Area Figure 1 - Safe Operating Area Vin = 12 V, Output Voltage = 3.3 V (See Note A) Vin = 12 V, Output Voltage = 5 V (See Note A) 90 100 80 90 70 Vout 400 LFM 60 80 5.0V 200 LFM 3.3V 100 LFM 1.8V Nat conv 50 1.2V 70 40 60 30 50 20 0248 6 0248 6 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 3 - Safe Operating Area Figure 4 - Efficiency vs Load Current Vin = 12 V, Output Voltage = 1.8 V (See Note A) Vin = 12 V (See Note B) N No ot te es s A SOA curves represent the conditions at which internal components are Track within the Artesyn derating guidelines. 5 B Characteristic data has been developed from actual products tested at Track 25 °C. This data is considered typical data for the converter. 2 8 3 Vo Vin Vin Vo PTVxx010 Inhibit GND Vo Adj L 7 6 1 4 O A Inhibit Rset D C2 1% C3 C1 10uF 0.05W 100uF 100uF Ceramic Optional (Required) (Required) GND GND Figure 5 - Standard Application File Name: ptv12010w.pdf Rev (02): 19 Dec 2005 TEMPERATURE (ºC) TEMPERATURE (ºC) EFFICIENCY (%) TEMPERATURE (ºC) PTV12010 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product PTV12010L Characteristic Data 90 100 80 90 70 Vout 400 LFM 60 80 1.2V 200 LFM 1.0V 100 LFM 0.8V Nat conv 50 70 40 60 30 50 20 0248 6 0248 6 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 6 - Safe Operating Area Figure 7 - Efficiency vs Load Current Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A) Vin = 12 V (See Note B) N No ot te es s Track A SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. 5 Track B Characteristic data has been developed from actual products tested at 2 25 °C. This data is considered typical data for the converter. 8 3 Vo Vin Vin Vo PTVxx010 Inhibit GND Vo Adj L 7 6 1 4 O A Inhibit Rset D C2 1% C3 C1 10uF 0.05W 100uF 100uF Ceramic Optional (Required) (Required) GND GND Figure 8 - Standard Application File Name: pth12010wl.pdf Rev (06): 07 Feb 2005 TEMPERATURE (ºC) EFFICIENCY (%) PTV12010 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 5 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product SIDE VIEW FRONT VIEW 0.330±0.008 (8.38±0.20) PCB 0.900 (22.86) 0.400 (10.16) 0.150 (3.81) 1 23457 6 8 0.025 (0.64) Min 8 Places 0.020 (0.51) Plated Through Hole 0.100 (2.54) Dimensions in Inches (mm) Tolerances (unless otherwise specified) 0.100 (2.54) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) PIN CONNECTIONS PIN NO. FUNCTION 1 Ground 2 Vout 3 Vout 4 Vo Adjust 5 Track 6 Ground 7 Inhibit 8Vin Figure 9 - Mechanical Drawing and Pinout Table Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 4 Application Note www.artesyn.com File Name: ptv12010w.pdf Rev (02): 19 Dec 2005