ARTESYN PTV12020WAD

PTV12020 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 1 NEW Product • 16 A output current • 12 V input voltage • Wide-output voltage adjust • 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’ • Auto-track™ sequencing* • Pre-bias start-up • Efficiencies up to 93% • Output ON/OFF inhibit • Vertical through-hole mounting • Point-of-Load-Alliance (POLA) compatible • Undervoltage lockout • Available RoHS compliant The PTV12020 is a non-isolated dc-dc converter from Artesyn under the Point of Load Alliance (POLA) standard. The vertical mounting option of the PTV12020 module provides performance in less than 20% of the space that is required by alternative solutions. The Auto-Track™ feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including DSP’s, FPGA’s and ASIC’s requiring controlled power-up and power-down. The PTV12020 has an input voltage of 10.8 Vdc to 13.2 Vdc and offers a wide 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’ output voltage range with up to 16 A output current, 2 YEAR WARRANTY which allows for maximum design flexibility and a pathway for future upgrades. All specifications are typical at nominal input, full load at 25 °C unless otherwise stated SPECIFICATIONS C = 560 μF (non-ceramic) and 22 μF (ceramic), C = 0 μF in out OUTPUT SPECIFICATIONS EMC CHARACTERISTICS Voltage adjustability Suffix ‘W’ 1.2-5.5 Vdc Electrostatic discharge EN61000-4-2, IEC801-2 (See Note 4) Suffix ‘L’ 0.8-1.8 Vdc Conducted immunity EN61000-4-6 Radiated immunity EN61000-4-3 Setpoint accuracy (See Note 8) ±2.0% Vo GENERAL SPECIFICATIONS Line regulation Suffix ‘W’ ±5 mV typ. Suffix ‘L’ ±10 mV typ. Efficiency See Tables on page 2 Load regulation Suffix ‘W’ ±10 mV typ. Insulation voltage Non-isolated Suffix ‘L’ ±12 mV typ. Switching frequency Total regulation (See Note 8) ±3.0% Vo Suffix ‘W’ 250-400 kHz 325 kHz typ. Suffix ‘L’ 200-300 kHz 250 kHz typ. Minimum load 0 A Approvals and EN60950 Ripple and noise Suffix ‘W’ V <2.5 V 1.0% V o o standards UL/cUL60950 20 MHz bandwidth Suffix ‘W’ V >2.5 V 1.5% V o o Suffix ‘L’ 2.0% V o Material flammability UL94V-0 Temperature co-efficient -40 ºC to +85 ºC ±0.5% Vo Dimensions (L x W x H) 44.45 x 9.39 x 12.70 mm 1.75 x 0.37 x 0.50 in Transient response 70 μs recovery time (See Note 5) Overshoot/undershoot 100 mV Weight 5.5 g (0.19 oz) INPUT SPECIFICATIONS MTBF Telcordia SR-332 4,900,000 hours Input voltage range (See Note 3) 10.8-13.2 Vdc ENVIRONMENTAL SPECIFICATIONS Input standby current 10 mA typ. Thermal performance Operating ambient, -40 ºC to +85 ºC (See Note 2) temperature Remote ON/OFF (See Note 1) Positive logic Non-operating -40 ºC to +125 ºC Undervoltage lockout (Increasing) 9.5 V typ. PROTECTION Track input current Pin 9 (See Notes 6, 7) 0.13 mA Overcurrent Auto reset 30 A typ. Overtemperature Auto recovery International Safety Standard Approvals UL/cUL CAN/CSA-C22.2 No. 60950 File No. E174104 *Auto-track™ is a trade mark of Texas Instruments TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL File Name: ptv12020w.pdf Rev (02): 19 Dec 2005 PTV12020 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product OUTPUT OUTPUT OUTPUT REGULATION INPUT OUTPUT EFFICIENCY MODEL POWER CURRENT CURRENT (9,10) VOLTAGE VOLTAGE (MAX.) NUMBER (2) LINE LOAD (MAX.) (MIN.) (MAX.) 28.8 W 10.8-13.2 Vdc 0.8-1.8 Vdc 0 A 16 A 89% ±10 mV ±12 mV PTV12020L 88 W 10.8-13.2 Vdc 1.2-5.5 Vdc 0 A 16 A 94% ±5 mV ±10 mV PTV12020W Part Number System with Options PTV12020W AH (9) Product Family Mounting Style Point of Load Alliance D = Horizontal Through-Hole (Matte Sn) Compatible H = Horizontal Through-Hole (Sn/Pb) Mounting Version V = Vertical Pin Style A = Through-Hole Std. Pin Length (0.150”) Input Voltage 12 = 12 V Output Voltage Code Output Current W = Wide, L = Low Voltage 02 = 16 A Mechanical Package Always 0 O Ou ut tp pu ut t V Vo ollt ta ag ge e A Ad djju us st tm me en nt t o of f t th he e P PT TV V1 12 20 02 20 0 S Se er riie es s The ultra-wide output voltage trim range offers major advantages to users who select the PTV12020. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc for suffix ‘L’. When the PTV12020 converter leaves the factory the output has been adjusted to the default voltage of 1.2 V for the PTV12020W and 0.8 V for PTV12020L. EFFICIENCY TABLE - PTH12020L (I = I ) EFFICIENCY TABLE - PTV12020W (I = I ) O OMAX O OMAX OUTPUT VOLTAGE EFFICIENCY OUTPUT VOLTAGE EFFICIENCY Vo = 1.8 V 87% Vo = 5.0 V 93% Vo = 1.5 V 85% Vo = 3.3 V 91% Vo = 1.2 V 83% Vo = 2.5 V 89% Vo = 1.0 V 80% Vo = 1.8 V 86% Vo = 0.8 V 77% Vo = 1.5 V 84% Vo = 1.2 V 81% N No ot te es s source. Therefore to ensure a pre-bias hold-off, one of the following two 1 Remote ON/OFF. Positive logic techniques must be followed when input power is first applied to the ON: Pin 3 open; or V > 2 V module. The Auto-Track™ function must either be disabled, or the OFF: Pin 3 GND; or V < 0.6 V). module’s output held off using the Inhibit pin. Refer to Application Note 2 See Figures 1, 2, 3 and 6 for safe operating area curves. 199 for more details. 3 A 560 μF electrolytic input capacitor is required for proper operation as 8 The set-point voltage tolerance is affected by the tolerance and stability well as a 22 μF high-frequency ceramic capacitor. The electrolytic of R . The stated limit is unconditionally met if R has a tolerance of capacitor must be rated for the minimum rms of ripple current. set set 1% with 100/ºC or better temperature stability. 4 An external output capacitor is not required for basic operation. Adding 9 To order Pb-free (RoHS compatible) through-hole parts replace the 330 μF of distributed capacitance at the load will improve the transient mounting option ‘H’ with ‘D’, e.g. PTV12020WAD. response. 10 NOTICE: Some models do not support all options. Please contact your 5 1 A/μs load step, 50 to 100% I , C3 = 330 μF. omax local Artesyn representative or use the on-line model number search tool at 6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). http://www.artesyn.com/powergroup/products.htm to find a suitable 7 The pre-bias start-up feature is not compatible with Auto-Track™. This is alternative. because when the module is under Auto-Track™ control, it is fully active and will sink current if the output voltage is below that of a back-feeding File Name: ptv12020w.pdf Rev (02): 19 Dec 2005 PTV12020 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product PTV12020W Characteristic Data 90 90 80 80 70 70 400 LFM 400 LFM 60 60 200 LFM 200 LFM 100 LFM 100 LFM 50 Nat conv 50 Nat conv 40 40 30 30 20 20 0 4 8 12 16 0 4 8 12 16 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 2 - Safe Operating Area Figure 1 - Safe Operating Area Vin = 12 V, Output Voltage = 3.3 V (See Note A) Vin = 12 V, Output Voltage = 5 V (See Note A) 90 100 80 90 70 Vout 400 LFM 80 60 5.0V 200 LFM 3.3V 100 LFM 2.5V 50 Nat conv 1.8V 70 1.5V 1.2V 40 60 30 50 20 04 8 12 16 0 4 8 12 16 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 3 - Safe Operating Area Figure 4 - Efficiency vs Load Current Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A) Vin = 12 V (See Note B) N No ot te es s Vo Sense A SOA curves represent the conditions at which internal components are Track within the Artesyn derating guidelines. 9 7 B Characteristic data has been developed from actual products tested at Track Sense 25 °C. This data is considered typical data for the converter. 5, 6 3, 4 Vo Vin Vin Vo PTVxx020 Inhibit GND Vo Adj 12 L 10. 11 1, 2 8 O A Inhibit D Rset C2 1% C3 C1 22uF 0.05W 330uF 560uF Ceramic Optional (Required) (Required) GND GND Figure 5 - Standard Application File Name: ptv12020w.pdf Rev (02): 19 Dec 2005 TEMPERATURE (ºC) TEMPERATURE (ºC) EFFICIENCY (%) TEMPERATURE (ºC) PTV12020 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product PTV12020L Characteristic Data 90 100 80 90 70 Vout 400 LFM 80 60 1.8V 200 LFM 1.5V 100 LFM 1.2V 50 Nat conv 70 1.0V 0.8V 40 60 30 50 20 04 8 12 16 0 4 8 12 16 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 6 - Safe Operating Area Figure 7 - Efficiency vs Load Current Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A) Vin = 12 V (See Note B) N No ot te es s Vo Sense Track A SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. 9 7 Track Sense B Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the converter. 5, 6 3, 4 Vo Vin Vin Vo PTVxx020 Inhibit GND Vo Adj L 12 10. 11 1, 2 8 O A Inhibit D Rset C2 1% C3 C1 22uF 0.05W 330uF 560uF Ceramic Optional (Required) (Required) GND GND Figure 8 - Standard Application File Name: pth12020wl.pdf Rev (01): 01 June 2005 TEMPERATURE (ºC) EFFICIENCY (%) PTV12020 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 5 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product SIDE VIEW FRONT VIEW 0.370 (9.39) MAX. 0.500 (12.7) PCB 1.750 (44.45) 0.150 (3.81) 0.640 (16.26) 12 3 4 5 6 7 8 9 10 11 12 0.025 (0.64) Min 12 Places 0.050 (1.27) 0.650 (16.51) Plated Through Hole 0.020 (0.51) TYP. 0.100 (2.54) TYP. Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) PIN CONNECTIONS PIN NO. FUNCTION 1 Ground 2 Ground 3 Vout 4 Vout 5Vin 6Vin 7 Vo Sense 8 Vo Adjust 9 Track 10 Ground 11 Ground 12 Inhibit Figure 9 - Mechanical Drawing and Pinout Table Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 4 Application Note www.artesyn.com File Name: ptv12020w.pdf Rev (02): 19 Dec 2005