ARTESYN SIL06C-12SADJ-VJ

POWER SIL06C Series Data Sheet C-Class Non-Isolated Total Power: 30 Watts Input Voltage: 4.5 - 13.8 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 6 A current rating ƒ Input voltage range: 4.5 - 5.5 Vdc or 10.2 - 13.8 Vdc ƒ Output voltage: 0.9 - 5.0 V Electrical Specifications ƒ Industry-leading value Input ƒ Cost optimized design Input voltage ra nge 5 V input model 4.5 - 5.5 Vdc ƒ Excellent transient response 12 V input model 10.2 - 13.8 Vdc ƒ Output voltage adjustability Input current No load 50 mA Remote OFF 5 mA ƒ Path for future upgrades Input current (max.) 5 V input model 5.1 A @ lo max. ƒ Supports silicon voltage migration (See Note 9) 12 V input model 1.6 A @ Io max. ƒ Reduced design-in and qual time Input reflected ripple 5 V input model 52 mA (pk-pk) (See Note 2) 12 V input model 56 mA (pk-pk) ƒ Designed-in reliability: MTBF of 7 million hours per Telcordia SR-332 Remote ON/OFF Logic compatibility Active high ƒ Available RoHS compliant ON >2.4 Vdc ƒ Two year warranty OFF <0.8 Vdc Start-up time Power up <20 ms Remote ON/OFF <20 ms SAFETY Turn ON threshold 5 Vin 4.5 Vdc ƒ UL, cUL CAN/CSA 22.2 No. 12 Vin 9.0 Vdc E139421 Turn OFF threshold 5 Vin 4.3 Vdc ƒ UL6950 File No. E139421 12 Vin 7.5 Vdc ƒ TÜV Product Service (EN60950) Output ƒ Certificate No. B 04 08 19870 228 Voltage adjustability 5 V input model 0.9 - 3.3 Vdc (See Note 7) 12 V input model 0.9 - 5.0 Vdc ƒ CB report and certificate to IEC60950 Output setpoint accuracy with 1.0% trim resistors ±2.5% Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% Min/Max load 0 A/6 A Overshoot 5 V input model 3.0% max. (at turn on) 12 V input model 1.0% max. Undershoot 100 mV max. Ripple and noise 5 Hz to 20 MHz (See Note 2) See table Transient response Deviation 75 mV; 150 μs recovery to within (See Note 1) regulation band All specifications are typical at nominal input, full load at 25°C unless otherwise stated. SIL06C Data Sheet General Specifications Environmental Specifications Efficiency See Table Thermal performance Operating ambient temperature -0 °C to +80 °C (See Note 8) Non-operating temperature -40 °C to +125 °C Switching frequency Fixed 200 kHz typical Protection Approvals and (See Note 4) TÜV Product Services standards EN60950, UL/cUL60950 Short-circuit Hiccup, non latching Material flammability UL94V-0 Recommended System Capacitance Weight 9.3 g (0.3 oz) Input capacitance (See Note 11) 270 μF / 20 mW ESR max. MTBF Telcordia SR-332 7,562,142 hours Output capacitance (See Note 11) 680 μF / 10 mW ESR max. Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (3,5) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load SIL06C-05SADJ-VJ 20 W 4.5 - 5.5 Vdc 0.9 - 3.3 V 0 A 6 A 89% ±0.2% ±0.5% SIL06C-12SADJ-VJ 30 W 10.2 - 13.8 Vdc 0.9 - 5.0 V 0 A 6 A 91% ±0.2% ±0.5% Part Number System with Options Product Family Rated Output Performance Input Voltage Number of Mounting Packaging Current Outputs Option Options SIL 06 C - 12 SADJ - V J 06 = 06 Amps C = Cost Optimized 05 = 4.5 - 5.5 Single Adjustable V = Vertical J = Pb free (RoHS SIL = Single In Line 12 = 10.2 - 13.8 Output H = Horizontal 6/6 compliant) Notes: Output Voltage Adjustment 1. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.5 lo max. to 0.75 lo max. and 0.75 lo max to 0.5 lo max. The ultra-wide output voltage trim range offers major advantages to users who select the SIL06C series. It is no longer necessary to purchase a variety 2. Measured with external filter. See Application Note 131 for details. of modules in order to cover different output voltages. The output voltage can 3. Power up is the time from application of dc input to Power Good enabled. Remote ON/OFF is from be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SIL06C series ON/OFF asserted high to Power Good enabled. converterleaves the factory the output has been adjusted to the default 4. This product is only for inclusion by professional installers within other equipment and must not be voltage of 0.9 V. operated as a stand-alone product. 5. The standard unit with the suffix ‘-V’ is for vertical mounting. To order a unit with horizontal mounting, please add the suffix ‘-H’ to the model number, e.g. SIL06C-05SADJ-HJ.6. Airflow Ripple and Noise Specification dependent, 300 LFM minimum required. Model Output Voltage Pk - Pk RMS 6. Measured as per recommended set-up. Cin = 270 μF (20 mW ESR max.). Cout = 680 μF (10 mW ESR max.). 5 V input models 0.9 - 2.5 Vdc 30 mV 15 mV 7. Uses external resistor from trim to output ground. Minimum value 485 Ω for 5 V model, 280 Ω for 3.3 Vdc 40 mV 15 mV 12 V model. See Applications Note 131 for details. 12 V input models 0.9 - 2.5 Vdc 40 mV 20 mV 8. Signal line assumed <3 m. 3.3 Vdc 50 mV 20 mV 9. External input fusing recommended. 10. See Application Note 131 for operation above 50 ºC. 11. See Application Note 131 for more details. 12. These models have a wide trim output. 5 Vin has an output of 0.9 Vdc to 3.3 Vdc and 12 Vin has an output of 0.9 Vdc to 5 Vdc. An external resistor adjusts the output voltage. 13. To order a unit with a pin length of 0.150”, please add suffix ‘P4’ to the model number, e.g. SIL06C-05SADJ-HP4J. 14. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. SIL06C Data Sheet Mechanical Drawings Mating Connectors Horizontal Mount 1.200 (30.48) 0.050 (1.27) Pin 8 Pin 1 0.015 (0.38) 0.150 0.025 ±0.001 (3.80) (0.64) Typ. ±0.025 0.100 5X (2.54) 0.950 (24.13) Mechanical Support Pin 0.025 ±0.001 (0.64) Typ. ±0.025 All dimensions in INCHES (mm) General tolerance ±0.01in (±0.25mm) except where specied otherwise Vertical Mount 1.200 0.062 (30.48) (1.57) Ref. Pin 1 Pin 8 0.050 (1.27) Typ. 0.050 0.025 ±0.001 (1.27) (0.64) Typ. ±0.025 0.025 ±0.001 0.150 (0.64) Typ. ±0.025 (3.81) 0.100 5X (2.54) 0.950 Pin Assignments (24.13) Pin Function All dimensions in inches (mm) 1 Vout General tolerance ±0.01in (±0.25mm) except where specied otherwise 2 Trim 3 Ground 4 Power Good 5 Remote ON/OFF 6 Vin 7 Mechanical support 8 Mechanical support 9 Mechanical support (Horiz only) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SIL06C DS 26Mar2015 0.062 (1.57) PCB Ref 0.315 (8.00) max. 0.070 (1.78) 0.315 (8.00) max 0.610 0.150 (15.49) (3.81) Ref 0.120 (3.05) 9 Places 0.610 0.040 (15.49) (1.02) Ref. 0.150 (3.81) 8 Places 0.527 (13.38) 0.530 (15.01) 0.040 (1.02)