ARTESYN SIL10E-12W3V3-VJ

process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev.3.4.09_96 SIL10E_05 Series 1 of 4 652 SIL10E Series 3.0 Vin - 5.5 Vin Total Power: 49.9 Watts Input Voltage: 3.0-5.5 Vdc # of Outputs: Single Electrical Specifications Input Special Features Input voltage range: 3.0-5.5 Vdc • 10 A Current rating Input current: • Input voltage range: No load 70 mA 3 Vdc to 5.5 Vdc Input current (max.): 8 A max. @ lo max. • Output voltage range: and Vout = 3.3 V 0.8 Vdc to 3.63 Vdc • Ultra high efficiency: Input reflected ripple: 65 mA rms 96% @ 5 Vin and 3.3 Vout Remote ON/OFF: (See Note 2) • Extremely low internal power dissipation Start-up time: 20 ms • Minimal thermal Output design concerns • Designed in reliability: Voltage adjustability: Fixed output versions ±10% MTBF of 7,000,000 hours per (See Note 1) 5 Vin with wide trim 0.8 - 3.63 Vdc Telcordia SR-332 3.3 Vin with wide trim 0.8 - 2.75 Vdc • Ideal solution where board Setpoint accuracy: ±0.4% typ. space is at a premium or tighter card pitch is required Line regulation: ±0.2% typ. • Industry standard Load regulation: ±1.0% typ. footprint and pin out • Available RoHS compliant Minimum load: 0 A • 2 year warranty Overshoot/Undershoot: None Ripple and noise: 50 mV pk-pk Safety 25 mV rms max. • UL/cUL CAN/CSA 22.2 Temperature co-efficient: ±0.01%/˚C No. 60950-1-03/UL 60950-1, Transient response: File No. E186249 50 mV max. deviation 50µs recovery to within ±1.0% • TÜV Product Service Remote sense: 10% Vo compensation (EN60950) Certificate No. B 08 05 51485 378 All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. • CB report and certificate to IEC60950, Certificate No. DE3-51686M1 process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev.3.4.09_96 SIL10E_05 Series 2 of 4 652 EMC Characteristics Electrostatic discharge: EN61000-4-2, IEC801-2 Conducted immunity: EN61000-4-6 EN61000-4-3 Radiated immunity: General Specifications Efficiency: See table Insulation voltage: Non-isolated Switching frequency: Fixed 300 kHz typ. Approvals and standards: EN60950 UL/cUL60950 Material flammability: UL94V-0 Dimensions (L x W x H) 50.8 x 7.8 x 12.7 mm 2.0 x 0.31 x 0.5 inches Pin length: (Vertical) 0.135 ± 0.02 in (3.43 ± 0.5 mm) Weight: 5 g (0.18 oz) MTBF: Telcordia SR-332 7,042,000 hours MIL-HDBK-217F 680,000 hours Environmental Specifications Thermal performance: Operating ambient temperature -40° C to +100 °C (See Note 3) Non-operating -40 °C to +125 °C Protection Short circuit: Continuous Thermal: Automatic recovery process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev.3.4.09_96 SIL10E_05 Series Ordering Information 3 of 4 652 All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Ordering Information Output Currents Regulation Output Efficiency (4, 5, 6) Input Voltage Output Voltage Model Numbers Power (Max.) (typ.) Min Max Line Load 8.8 W 3.0 - 5.5 Vdc 0.8 V 0 A 10 A 83% ±0.2% ±1.5% SIL10E-05S0V8-VJ (EOL) 11 W 3.0 - 5.5 Vdc 1 V 0 A 10 A 86% ±0.2% ±1.5% SIL10E-05S1V0-VJ (EOL) 13.2 W 3.0 - 5.5 Vdc 1.2 V 0 A 10 A 88% ±0.2% ±1.0% SIL10E-05S1V2-VJ (EOL) 16.5 W 3.0 - 5.5 Vdc 1.5 V 0 A 10 A 90% ±0.2% ±1.0% SIL10E-05S1V5-VJ (EOL) 19.8 W 3.0 - 5.5 Vdc 1.8 V 0 A 10 A 92% ±0.2% ±1.0% SIL10E-05S1V8-VJ (EOL) 22 W 3.0 - 5.5 Vdc 2 V 0 A 10 A 93% ±0.2% ±1.0% SIL10E-05S2V0-VJ (EOL) 27.5 W 3.0 - 5.5 Vdc 2.5 V 0 A 10 A 94% ±0.2% ±1.0% SIL10E-05S2V5-VJ (EOL) 36.3 W 4.5 - 5.5 Vdc 3.3 V 0 A 10 A 95% ±0.2% ±1.0% SIL10E-05S3V3-VJ (EOL) 36.3 W 4.5 - 5.5 Vdc 0.8 - 3.63 V 0 A 10 A 95% ±0.2% ±1.0% SIL10E-05W3V3-VJ Part Number System with Options SIL10E-05S3V3-VJ Product Family (5) Packaging Options SIL = Single In Line J = Pb-free RoHS 6/6 compliant Mounting Options Rated Output Current V = Vertical Mount 10 = 10 Amps H = Horizontal Mount Output Voltage Performance 2.5 V, 3.3 V, etc E = Enhanced Performance Number of Outputs Input Voltage S = Single 05 = 3.0 V to 5.5 V W = Wide 12 = 10 V to 14 V Output Voltage Adjustment of the SIL10E-05W3V3J Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL10E-05W3V3J. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.8 Vdc to 3.63 Vdc. When the SIL10E-05W3V3J converter leaves the factory the output has been adjusted to the default voltage of 3.3 V. • When Vin ≥ 4.5 V, then Vout can be adjusted from 0.8 Vdc to 3.6 Vdc • When Vin < 4.5 V, then Vout can be adjusted from 0.8 Vdc to 2.75 Vdc Notes Notes Continued 1 When Vin ³ 4.5 V, then Vout can be adjusted from 0.8 V to 3.6 V. When Vin < 4.5 V, then Vout 3 Full derating curves available in both the Longform Datasheet and Application can be adjusted from 0.8 V to 2.75 V. Note 136. 2 The SIL10E features a ‘Negative Logic’ Remote ON/OFF operation. If you are not using the 4 For certain applications that use low ESR capacitors on the output of the Remote ON/OFF pin, leave the pin open (the converter will be on). The Remote ON/OFF pin is convertor and to insure maximum converter stability, please add the suffix ‘02’ referenced to ground. to the model, e.g. SIL10E-05S2V5-V02J. 5 TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. The following conditions apply for the SIL10E: 6 NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number Configuration Converter Operation search tool at http://www.PowerConversion.com to find a suitable alternative. Remote pin open circuit Unit is ON Remote pin pulled low Unit is ON Remote pin pulled high [Von/off >1.2 V] Unit is OFF process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev.3.4.09_96 SIL10E_05 Series Americas 4 of 4 652 Mechanical Drawings 5810 Van Allen Way Carlsbad, CA 92008 USA PIN VIEW Telephone: +1 760 930 4600 2.000 0.020 Facsimile: +1 760 930 0698 (50.80 0.50) 0.500 (12.70) PCB SIDE VIEW Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX 54 3 2 1 62 53 1 United Kingdom J2 J1 Telephone: +44 (0) 1384 842 211 0.316 0.008 (8.03 0.20) Facsimile: +44 (0) 1384 843 355 0.100 (2.54) 0.170 (4.32) 1.900 (48.26) 0.050 (1.27) Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Dimensions in Inches (mm) Hong Kong Tolerances (unless otherwise specified) 2 Place 0.15 Telephone: +852 2176 3333 3 Place 0.006 Facsimile: +852 2176 3888 Figure 1: Horizontal Mount Version For global contact, visit: www.PowerConversion.com techsupport.embeddedpower SIDE VIEW FRONT VIEW @emerson.com 0.307 0.008 2.000 0.020 (7.80 0.20) (50.80 0.50) While every precaution has been taken to ensure 0.500 (12.70) accuracy and completeness in this literature, Emerson PCB Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. 0.135 (3.43) 0.635 (16.13) Emerson Network Power. The global leader in enabling 1 15 2 3 4 2 3 56 business-critical continuity. 0.025 0.001 J2 J1 (0.64 0.02) 0.168 (4.26) AC Power 0.100 (2.54) Connectivity 0.050 (1.27) 1.900 (48.26) DC Power Dimensions in Inches (mm) Tolerances (unless otherwise specified) Embedded Computing 2 Place 0.15 3 Place 0.006 Embedded Power Figure 2: Vertical Mount Version Monitoring Input Pin Connections Input Pin Connections Outside Plant J1 J2 Power Switching & Controls Pin 1 +Vout Pin 1 Ground Precision Cooling Racks & Integrated Cabinets Pin 2 +Vout Pin 2 +Vin Pin 3 Remote Sense (+) Pin 3 +Vin Services Surge Protection Pin 4 +Vout Pin 4 No Pin Pin 5 Ground Pin 5 Trim EmersonNetworkPower.com Pin 6 Remote ON/OFF Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co. 0.025 0.001 (0.64 0.02)