ARTESYN SIL20C2-00SADJ-VJ

POWER SIL/SMT20C2 Series Data Sheet C-Class Non-Isolated Total Power: 20 Amps Input Voltage: 4.5 - 13.8 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 20 A current rating ƒ Input voltage range: 4.5 - 13.8 Vdc ƒ Output voltage: 0.59 - 5.1 V ƒ Industry-leading value Electrical Specifications ƒ Cost optimized design Input ƒ Excellent transient response Input voltage ra nge 4.5 - 13.8 Vdc ƒ Output enable Input current Minimum load 50 mA ƒ Output voltage adjustability Remote OFF 5 mA ƒ Path for future upgrades Input current (max.) See Note 3 18 A @ lo max. ƒ Supports silicon voltage migration Start-up time Remote ON/OFF 3 ms ƒ Reduced design-in and qual time Output ƒ Current sink capability Output voltage See Note 5 0.59 - 5.1 V ƒ RoHS compliant Output setpoint accuracy 0.1% trim resistors ±1.0% ƒ Two year warranty Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% SAFETY Min./max. load 0 A/20 A ƒ UL, cUL CAN/CSA 22.2 No. Overshoot At turn-on 0.5% max. ƒ TÜV Product Service (EN60950) Undershoot At turn-off 100 mV max. ƒ CB report and certificate to Ripple and noise See Note 1 30 mV IEC60950 5 Hz to 20 MHz Vin = 5 V, Vout = 2.5 V Transient response See Note 1, 2 130 mV max. deviation; 50 μs recovery to within regulation band General Efficiency Vin = 5 V, Vo = 2.5 V, lo = 20 A 90% Switching frequency Fixed 750 kHz Material flammability UL94V-0 Approvals and standards EN60950; UL/cUL6950 Weight 8.50 g (0.03 oz.) MTBF 12 V @ 40 °C, 100% load 6,721,853 hours Bellcore 332 Coplanarity 150 μm All specifications are typical at nominal input, full load at 25 °C, unless otherwise stated. SIL/SMT20C2 Series Data Sheet Environmental Specifications Thermal performance Operating ambient temperature -0 °C to +70 °C See Note 5 Non-operating temperature -40 °C to +125 °C Protection Short-circuit Hiccup, non-latching Overvoltage protection Hiccup, non-latching Recommended System Capacitance Input See Note 6 0 μF Output See Note 7 0 μF Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (8) Number (Max.) Voltage Mount Voltage (Min.) (Max.) (Typical) Line Load SIL20C2-00SADJ-HJ 100 W 4.5 - 13.8 Vdc Horizontal 0.59 - 5.1 V 0 A 20 A 93% ±0.2% ±0.5% SIL20C2-00SADJ-VJ 100 W 4.5 - 13.8 Vdc Vertical 0.59 - 5.1 V 0 A 20 A 93% ±0.2% ±0.5% SMT20C2-00SADJJ 100 W 4.5 - 13.8 Vdc Horizontal 0.59 - 5.1 V 0 A 20 A 93% ±0.2% ±0.5% Surface Mount Part Number System with Options Product Family Rated Output Performance Generation Input Voltage Output Voltage Mounting Option RoHS Compliance Current SXX 20 C 2 - 00 SADJ - V J SIL = Single In Line 06 = 6 Amp C = Cost Blank = Standard 00 = 4.5 - 13.8 V Single Adjustable V = Vertical J = Pb free (RoHS SMT = Surface Mount 15 = 15 Amp Optimized 2 = Increased Output H = Horizontal 6/6 compliant) 20 = 20 Amp current density Blank = Horizontal 30 = 30 Amp Surface Mount 40 = 40 Amp Output Voltage Adjustment Standard Application Drawing The ultra-wide output voltage trim range offers major advantages to users Power Good who select the SIL/SMT40C2 series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59 - 5.1 V. When the SIL20C2 converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. 4 V 1 out Enable 5 Notes: 7 +R sense 1. Measured as per recommended system capacitance. SIL20C2 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. R 3. External input fusing is recommended. C out V in L 6 8 4. Additional part numbers may be available with different output voltages. 3 2 O A 5. Airflow dependent, 100 LFM minimum required. D C in 6. No capacitors needed for ripple current stability. R trim 7. No capacitors needed for stability. (for trim -R sense 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded down) Technologies representative or use the on-line model number search tool at GND http://www.Artesyn.com/power to find a suitable alternative. SIL/SMT20C2 Series Data Sheet Mechanical Drawings Vertical Mount 0.462 (11.73) Pin Assignments 1.200 (30.48) 0.295 (7.49) Pin Function 0.062 (1.57) PCB REF 1 Vout 0.105 (2.67) 2 Trim 0.610 (15.49) 3 Ground 4 Power Good 5 Enable 0.150 (3.81) TYP 6 Vin PIN 8 PIN 1 7 Remote Sense (+) 8 Remote Sense (-) 0.050 (1.27) REF 0.025 (0.64) ±.001 SQ PIN TYP 8 PLACES Dimensions in Inches (mm) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Horizontal Mount Pin Assignments 0.482 (12.24) Pin Function 0.295 (7.49) 1 Vout 0.025 (0.64) ±.001 1.200 (30.48) 2 Trim 0.062 (1.57) REF SQ PINS TYP PIN 9 9 PLACES 3 Ground 4 Power Good 5 Enable 0.535 (13.59) 0.610 (15.49) 6 Vin 7 Remote Sense (+) 8 Remote Sense (-) 0.040 (1.02) REF Mech Support PIN 1 9 (Horizontal version 0.120 (3.05) TYP only) 0.125 (3.18) TYP Dimensions in Inches (mm) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 0.000 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) 1.165 (29.59) 0 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) SIL/SMT20C2 Series Data Sheet Mechanical Drawings Mating Connectors Surface Mount Pin Assignments 1.200 (30.48) 0.065 (1.65) 0.015 (0.38) Pin Function 1 Vout PIN 8 2 Trim PIN 1 3 Ground 0.610 (15.49) 0.535 (13.59) 4 Power Good 5 Enable 6 Vin PIN 10 PIN 9 7 Remote Sense (+) 8 Remote Sense (-) Mech Support 9 (Horizontal Version only 0.025 (0.64) ±.002 0.482 (12.24) Mech Support PIN WIDTH TYP 10 (Horizontal Version only 0.295 (7.49) 0.062 (1.57) PCB REF 0.040 (1.02) Dimensions in Inches (mm) 2 Places ±0.030 (±0.76) 0.125 (3.18) TYP 3 Places ±0.010 (±0.25) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SIL/SMT20C2 Series 06Apr2015 0 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.48) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21)