ARTESYN SIL30C-12SADJ-VJ

POWER SIL30C Series Data Sheet C-Class Non-Isolated Total Power: 30 Amps Input Voltage: 10.2 - 13.8 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 30 A current rating ƒ Input voltage range: 10.2 - 13.8 Vdc ƒ Nominal output voltage: 0.9 - 5 V ƒ Industry-leading value Electrical Specifications ƒ Cost optimized design ƒ Excellent transient response Input ƒ Output voltage adjustability Input voltage ra nge Nominal 12 V 10.2 - 13.8 +Vdc ƒ Pathway for future upgrades Input current No load 230 mA Remote OFF 30 mA ƒ Supports silicon voltage migration Input current (max.) See Note 4 13.8 A max. @ Io max. and Vin = 10.8 V ƒ Reduced design-in and qual time Input reflexted ripple See Note 2 150 mA (pk-pk) ƒ Designed in reliability: MTBF of Remote ON/OFF >3.9 million hours per Telcordia Logic compatibility Logic high SR-332 ON >2.4 Vdc OFF <0.8 Vdc ƒ Current share ƒ RoHS compliant Start-up time See Note 5 Power up: 30 ms Remote ON/OFF: 30ms ƒ Two year warranty Turn ON threshold 9.0 Vdc Turn OFF threshold 7.6 Vdc SAFETY Output ƒ UL, cUL CAN/CSA 22.2 No. E139421 Voltage adjustability See Note 1 0.9 to 5.0 Vdc ƒ UL60950 File No. E139421 Output setpoint accuracy Using 1.0% trim resistors ±3.0% ƒ TÜV Product Service (EN60950) Line regulation Low line to high line ±0.2% Certificate No. B04 08 19870 228 Load regulation Full load to min. load ±1.5% ƒ CB report and certificate to Min./max. load 0 A/30 A US/6415C/UL Overshoot At turn-on 1.0% max. Undershoot At turn-off 10 mV max. Ripple and noise See Note 2 50 mV pk-pk 5 Hz to 20 MHz 15 mV rms Transient response See Note 3 75 mV typical deviation 150 μs recovery to within regulation band Current share Full load ±10% All specifications are typical at nominal input, full load at 25 °C, unless otherwise stated. SIL30C Series Data Sheet General Specifications Environmental Specifications Efficiency 91% Thermal performance Operating ambient temperature -0 °C to +80 °C (See Note 8) Non-operating temperature -40 °C to +125 °C Switching frequency Fixed 300 kHz typ. Protection Approvals and (See Note 7) TÜV Product Services standards EN60950, UL/cUL60950 Short-circuit Foldback, non-latching Material flammability UL94V-0 Over-temperature Hiccup, non-latching Weight 28.3 g (1 oz) Recommended System Capacitance MTBF Telcordia SR-332 4,456,655 hours Input capacitance (See Note 9) 270 μF / 20 mW ESR max. Output capacitance (See Note 9) 680 μF / 10 mW ESR max. Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (10, 12) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load SIL30C-12SADJ-VJ 150 W 10.2 - 13.8 Vdc 0.9 - 5 V 0 A 30 A 91% ±0.2% ±1.5% Part Number System with Options Product Family Performance Input Voltage Number of Outputs Output Voltage Mounting Option Packaging Options Rated Output Current SIL 30 C - 12 S ADJ - V J SIL = Single In Line C = Cost 12 = 10.2 - 13.8 S = Single Output ADJ = Adjustable V = Vertical J = Pb free (RoHS 30 = 30 Amp Optimized Vdc Ouput H = Horizontal 6/6 compliant) Notes: Output Voltage Adjustment 1. Uses external resistor from TRIM to output ground. See Application Note 132 for details. The ultra-wide output voltage trim range offers major advantages to users 2. Measured with external filter. See Application Note 132 for details. who select the SIL30C-12SADJ. It is no longer necessary to purchase a 3. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.5 lo max to 0.75 lo max and 0.75 lo variety of modules in order to cover different output voltages. The output max to 0.5 lo max. voltage can be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the 4. External input fusing is recommended. SIL30C-12SADJ converter leaves the factory the output has been adjusted to 5. Power up is the time from application of dc input to POWER GOOD high. Remote ON/OFF the default voltage of 0.9 V. asserted high to POWER GOOD high. 6. Signal line assumed <3 m. 7. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 8. See Application Note 132 for operation above 50 ºC. 9. See Application Note 132 for ripple current requirements. 10. The standard unit with the suffix ‘-V’ is for vertical mounting. To order a unit with horizontal mounting, please add the suffix ‘-H’ to the model number, e.g. SIL30C-12SADJ-HJ. 11. This model has a wide trim output of between 0.9 Vdc to 5 Vdc. An external resistor adjusts the output voltage. 12. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. SIL30C Series Data Sheet Mechanical Drawings Horizontal Mount Pin Assignments Pin Function 0.470 (11.94) 0.150 1 Trim (3.82) 2 No Pin 0.120 3 Ground (3.05) 4 Power Good 5 Not Connected 6 Current Share 7 Ground 0.090 (2.29) 8 Ground 1.200 (30.48) 0.150 9 Remote ON/OFF 0.100 (3.81) Ref. 0.290 (2.54) Typ. 10 Remote Sense (GND) 0.050 (7.46) 0.212 (1.27) 11 Remote Sense (O/P) 2.300 (5.38) (58.42) 0.120 12 Vin (3.05) 2.400 13 Vin (60.96) 14 Vin All dimensions in inches (mm) 15 Vout General tolerance ±0.015in (±0.30mm) except where specied otherwise 16 Vout 17 Ground 18 Vout 19 Ground 20 Vout 21 Ground 22 Vout Vertical Mount 23 Ground 24 Vout 0.52 ±0.02 (13.20 ±0.5) 2.400 (60.96) 0.09 ±0.02 (2.4 ±0.5) 0.062 (1.57) Ref 0.050 0.090 (1.27) Pin 1 (2.29) 0.100 0.025 ±0.001 (2.54) Typ 0.250 (0.64) Typ ±0.025 (6.35) 2.300 1.200 (58.42) 0.050 (30.48) 0.019 (1.27) Typ (0.48) Ref 0.025 ±0.001 (0.64) Typ. ±0.025 0.26 ±0.03 (6.591 ±0.76) All dimensions in inches (mm) General tolerance ±0.015in (±0.30mm) except where specied otherwise WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SIL30C Series 08Apr2015 1.250 (31.75 0.050 (1.27) Ref. 1.250 (31.75) 1.350 (34.36) 1.240 (31.40) 0.140 (3.56 Typ) 0.140 (3.56)