ARTESYN SIL40C2-00SADJ-HJ

POWER SIL/SMT40C2 Series Data Sheet C-Class Non-Isolated Total Power: 40 Amps Input Voltage: 4.5 - 13.8 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 40 A current rating ƒ Input voltage range: 4.5 - 13.8 Vdc ƒ Output voltage: 0.6 - 5 V ƒ Industry-leading value ƒ Cost optimized design Electrical Specifications ƒ Excellent transient response Input ƒ Output enable Input voltage ra nge 4.5 - 13.8 Vdc ƒ output voltage adjustability Input current Minimum load 50 mA ƒ path for future upgrades Remote OFF 5 mA ƒ Supports silicon voltage migration Input current (max.) See Note 3 25 A @ lo max. ƒ Reduced design-in and qual time Start-up time Remote ON/OFF 3 ms ƒ RoHS compliant Output Output voltage See Note 5 0.6 - 5 V SAFETY Output setpoint accuracy 0.1% trim resistors ±1.0% ƒ UL, cUL CAN/CSA 22.2 No. E139421 UL6950 File No. TBD Line regulation Low line to high line ±0.2% ƒ TÜV Product Service (EN60950) Load regulation Full load to min. load ±0.5% ƒ Certificate No. TBD Min./max. load 0 A/40 A ƒ CB report and certificate to Overshoot At turn-on 0.5% max. IEC60950 Undershoot At turn-off 100 mV max. Ripple and noise See Note 1 25 mV 5 Hz to 20 MHz Vin = 5 V, Vout = 2.5 V Transient response See Note 1, 2 130 mV max. deviation 50 μs recovery to within regulation band General Efficiency (high input) Vin = 5 V, Vo = 2.5 V, lo = 20 A 94% Switching frequency Fixed 500 kHz Material flammability UL94V-0 Weight 17 g (0.06 oz.) MTBF 12 V @ 40 °C, 100% load 6,749,409 hours Bellcore 332 Coplanarity Surface mount models 150 μm SIL/SMT40C2 Series Data Sheet Environmental Specifications Thermal performance Operating ambient temperature -0 °C to +70 °C See Note 5 Non-operating temperature -40 °C to +125 °C Protection Short-circuit Hiccup, non-latching Overvoltage protection Hiccup, non-latching Recommended System Capacitance Input See Note 6 0 μF Output See Note 7 0 μF Ordering Information Regulation Model Input Output Output Current Output Current Efficiency (3,5) Number Voltage Voltage (Min.) (Max.) (Typical) Line Load SIL40C2-00SADJ-VJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5% SIL40C2-00SADJHJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5% SMT40C2-00SADJJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5% Part Number System with Options Rated Output Performance Generation Input Voltage Output Voltage Mounting Option RoHS Compliance Product Family Current SIL 40 C 2 - 00 SADJ - V J 06 = 6 Amp C = Cost Blank = Standard 00 = 4.5 - 13.8 V Single Adjustable V = Vertical J = Pb free (RoHS SIL = Single In Line 15 = 15 Amp Optimized 2 = Increased Output H = Horizontal 6/6 compliant) SMT = Surface Mount 20 = 20 Amp current density 30 = 30 Amp (Applicable to SIL 40 = 40 Amp version only) Output Voltage Adjustment Standard Application Drawing The ultra-wide output voltage trim range offers major advantages to users Power Good who select the SIL40C2 series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.6-5 V. When the SIL40C2 converter leaves the factory, the output has been adjusted to the default voltage of 0.6 V. 6 V 1,2,3 out Notes: Enable 5 9 +R 1. Measured as per recommended system capacitance. sense 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. SIL40C2 3. External input fusing is recommended. V in R 10,11 C 4. Additional part numbers may be available with different output voltages. out L 7,8 4 O 5. Airflow dependent, 100 LFM minimum required. A 6. No capacitors needed for ripple current stability. D C in 7. No capacitors needed for stability. R trim 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded (for trim Technologies representative or use the on-line model number search tool at down) http://www.Artesyn.com/power to find a suitable alternative. GND 9. To order a Horizontal Mounting option with a pin length of 0.165”, please use model SIL40C2-00S-HP5. SIL/SMT40C2 Series Data Sheet Mechanical Drawings Vertical Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 1.200 (30.48) 0.427 (10.85) 0.255 (6.48) 1.100 (27.94) 0.062 (1.57) REF 0.110 (2.79) 0.050 (1.27) REF PIN 1 0.140 (3.56) TYP 0.100 (2.54) 0.100 (2.54) TYP 9 PLACES 1.050 (26.67) 0.050 (1.27) TYP 0.025 (0.64) ±.001 SQ PINS TYP Horizontal Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 1.200 (30.48) 0.468 (11.89) 0.062 (1.57) REF 1.100 (27.94) 0.255 (6.48) .150 (3.81) TYP PIN 1 0.110 (2.79) REF 2X 1.000 (25.40) 0.025 (0.64) ±.001 SQ PINS TYP 13 PLACES 0.050 (1.27) REF 0.100 (2.54) TYP 9 PLACES 2X 1.050 (26.67) 0.050 (1.27) 0.100 (2.54) REF SIL/SMT40C2 Series Data Sheet Mechanical Drawings Mating Connectors Surface Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 0.442 (11.23) 0.062 (1.57) REF 0.255 (6.48) 0.125 (3.18) TYP 0.110 (2.79) REF 1.200 (30.48) 1.100 (27.94) 2X 1.000 (25.40) 0.050 (1.27) REF PIN 1 0.100 (2.54) TYP 9 PLACES 0.050 (1.27) 2X 1.050 (26.67) Pin Assignments 0.100 (2.54) REF Pin Function 1 Vout 2 Vout 3 Vout 4 Trim 5 Enable 6 Power Good 7 Ground 8 Ground 9 (+) Sense 10 Vin 11 Vin 12 Mech Pin (Horz/SMT only) 13 Mech Pin (Horz/SMT only) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SIL/SMT40C2 Series 24Mar2015