ARTESYN SMT06C-05SADJJ

Embedded Power for Business-Critical Continuity Rev. 08.20.08_j93 SMT06C 1 of 4 SMT06C Series 5 Vin and 12 Vin single output Total Power: 20W Input Voltage: 4.5-5.5 Vdc or 10.2 - 13.8 Vdc # of Outputs: Single Electrical Specifications Special Features Output • 6 A current rating Voltage adjustability (see note 6) 5 V input models 0.9 - 3.3 Vdc • Input voltage range: 12 Vins 0.9 - 5.0 Vdc 4.5 Vdc - 5.5 Vdc or 10.2 Vdc - 13.8 Vdc Output setpoint accuracy 1.0% trim resistors ±2.5% • Output voltage range: Line regulation Low line to high line ±0.2% 0.9 Vdc - 3.3/5.0 Vdc • Industry leading value Load regulation Full load to min. load ±0.5% • Cost optimized design Min/max load 0 A / 6 A • Excellent transient response • Output voltage adjustability Overshoot (at turn on) 5 V input models 3.0% max. • Pathway for future 12 V input models 1.0% max. upgrades Undershoot At turn-off 100 mV max. • Supports silicon voltage migration Ripple and noise 5 Hz to 20 MHz (See note 2) See table on page 2 • Resulting in reduced design-in and qualification Transient response (see note 1) 75 mV max. deviation time 150 μs recovery to • Designed in reliability: within regulation band MTBF of >7 million hours per Telcordia SR-332 • Available RoHS compliant • 2 year warranty Safety UL/cUL : CAN/CSA 22.2 No. 60950 TÜV Product Service (EN60950:2000) CB report and certificate Embedded Power for Business-Critical Continuity Rev. 08.20.08_j93 SMT06C All specifications are typical at nominal input, full load at 25°C unless otherwise stated. 2 of 4 Input Input voltage range 5 V input model 4.5 - 5.5 Vdc 12 V input model 10.2 - 13.8 Vdc Input current Minimum load 50 mA Remote OFF 5 mA Input current (max.) 5 V input model 5.1 A max. @ lo max. (see note 8) 12 V input model 1.6 A @ lo max. Input reflected ripple 5 Vin 52 mA (pk-pk) (see note 2) 12 Vin 56 mA (pk-pk) Remote ON/OFF Logic compatibility Positive logic ON >2.4 Vdc OFF <0.8 Vdc Start-up time (see note 3) Power up <20 ms Remote ON/OFF <20 ms Turn ON threshold 5 Vin 4.5 Vdc typ. 12 Vin 9.3 Vdc typ. Turn OFF threshold 5 Vin 4.3 Vdc typ. 12 Vin 7.8 Vdc typ. General Specifications Efficiency See table on page 2 Switching frequency Fixed 200 kHz. Approvals and standards (See note 4) TÜV product Services IEC69050, UL/cUL60950 Material flammability UL94V-0 Weight 9.3 g (0.3 oz.) Coplanarity 150 µm MTBF Telcordia SR-332 7,562,142 hours Environmental Specifications Thermal performance Operating ambient, 0 °C to +80 °C (see note 9) temperature Non-operating -40 °C to +125 °C Protection Short-circuit Hiccup, non-latching Recommended system capacitance Input capacitance (See note 10) 270 μF/20 mW ESR max. Output capacitance (See note 10) 680 μF/10 m W ESR max. Embedded Power for Business-Critical Continuity Rev. 08.20.08_j93 SMT06C Ordering Information 3 of 4 Output Output Output Regulation Input Output Maximum (12, 13) Power Current Current Model Numbers (11) Voltage Voltage Load (typ) (max) (min) (max) Line Load 4.5-5.5 Vdc 0.9-3.3 V ±0.2% ±0.5% 20 W 0 A 6 A 89% SMT06C-05SADJJ 30 W 10.2 - 13.8 Vdc 0.9-5.0 V 0 A 6 A 91% ±0.2% ±0.5% SMT06C-12SADJJ All specifications are typical at nominal input Vin = 12 V, full load at 25°C unless otherwise stated. Part Number System with Options Product Family Rated Output Performance Input Voltage Number of Outputs Packaging Options Current SMT 06 C 12 SADJ J SMT = Surface Mount 06 = 6 A C = C Series 05 = 4.5 Vdc to 5.5 Vdc J = PB-free (RoHS 6/6 compliant) SADJ = Single Adjustable 12 = 10.2 Vdc to 13.8 Vdc Output Output Voltage Adjustment of the SMT20C Series The ultra-wide output voltage trim range offers major advantages to users who select the SMT06C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SMT06C series converter leaves the factory the output has been adjusted to the default voltage of 0.9 V. Notes Ripple and Noise Specification 1 di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo max. to 0.75 lo Output max. and 0.75 lo max. to 0.5 lo max. Model Pk - Pk RMS 2 Measured with external filter. See Application Note 169 for details. Voltage 3 Power up is the time from application of dc input to Power Good high. Remote ON/OFF asserted high to Power Good high. 5 V input models 0.9 Vdc to 2.5 Vdc 30 mV 15 mV 4 This product is only for inclusion by professional installers within other 3.3 Vdc 40 mV 15 mV equipment and must not be operated as a stand alone product. 5 Measured as per recommended set-up. Cin = 270 μF (20 mW ESR max.). 12 V input models 0.9 Vdc to 2.5 Vdc 40 mV 20 mV Cout = 680 μF (10 mW ESR max.). 3.3 Vdc to 5 Vdc 50 mV 20 mV 6 Uses external resistor from trim to ground. Minimum value 485 W for 5 V model, 280 W for 12 V model. See Application Note 169 for details. 7 Signal line assumed <3 m. 8 External input fusing recommended. 9 See Application Note 169 for operation above 50 ºC. 10 See Application Note 169 for more details. 11 TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. 12 NOTICE: Some models do not support all options. Please contact your local representative or use the on-line model number search tool at www.powerconversion.com to find a suitable alternative. Embedded Power for Business-Critical Continuity Rev. 08.20.08_j93 Americas SMT06C Mechanical Drawing 5810 Van Allen Way 4 of 4 Carlsbad, CA 92008 USA 0.190 Telephone: +1 (760) 930 4600 (4.83) 0.190 Facsimile: +1 (760) 930 0698 (4.83) 1.200 0.190 (30.48) (4.83) 0.310 Europe (UK) 0.190 (7.87) (4.83) Waterfront Business Park PIN 5 PIN 2 Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) PIN 1 0.75 PIN 6 14/F, Lu Plaza 0.050 (1.90) (1.27) 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 Seating Plane For global contact, visit: 0.062 (1.57) REF www.powerconversion.com 0.019 6 x 0.089 (0.48) TYP technicalsupport@ (2.26) All dimensions in inches (mm) powerconversion.com All tolerance 0.010in (0.25mm) unless otherwise stated While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this Pin connections information or for any errors or omissions. Pin Number Function 1 Remote ON/OFF Emerson Network Power. 2 Power Good The global leader in enabling business-critical continuity. 3 Trim 4 Vout AC Power 5 GND Connectivity 6 Vin DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower. com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co. 0.466 (11.83) 0.530 Installed Ht. (13.46) 0.315 (8.00) 0.430 (10.93)