ARTESYN SMT15C-12SADJJ

POWER SMT15C Series Data Sheet Non-Isolated DC-DC Converter Total Power: 50 Watts Input Voltage: 4.5 - 5.5 Vdc or 10.2 - 13.8 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 15 A current rating ƒ Input voltage range: 4.5 - 5.5 Vdc or 10.2 - 13.8 Vdc ƒ Output voltage: 0.9 - 3.3 / 5.0 V Electrical Specifications ƒ Industry-leading value Input ƒ Cost optimized design Input voltage ra nge 4.5 - 5.5 Vdc ƒ Excellent transient response 10.2 - 13.8 Vdc ƒ Output voltage adjustability Input current Minimum load 65 mA Remote OFF 20 mA ƒ Path for future upgrades Input current (max.) 5 Vin 11.5 A max. @ lo max. ƒ Supports silicon voltage migration (See Note 9) 12 Vin 8.1 A @ Io max. ƒ Reduced design-in and qual time Input reflected ripple 5 Vin 200 mA (pk-pk) (See Note 2) 12 Vin 200 mA (pk-pk) ƒ Designed-in reliability: MTBF of >7 million hours per Telcordia SR-332 Remote ON/OFF Logic compatibility Positive logic ƒ Available RoHS compliant ON >2.4 Vdc ƒ Two year warranty OFF <0.8 Vdc Start-up time Power up <20 ms (See Note 3) Remote ON/OFF <20 ms SAFETY Turn ON threshold 5 Vin 4.5 Vdc ƒ UL, cUL CAN/CSA 22.2 No. 60950 12 Vin 9.3 Vdc ƒ UL 60690 File No. E139421 Turn OFF threshold 5 Vin 4.3 Vdc ƒ TÜV Product Service 12 Vin 7.8 Vdc (EN60950:2000) Output ƒ Certificate No. B 04 08 19870 228 Voltage adjustability 5 Vin 0.9 - 3.3 Vdc (See Note 7) 12 Vin 0.9 - 5.0 Vdc ƒ CB report and certificate to US/6415C/UL Output setpoint accuracy 1.0% trim resistors ±2.5% Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% Min/Max load 0 A/15 A Overshoot 5 Vin 3.0% max. (at turn on) 12 Vin 1.0% max. Undershoot At turn-off 100 mV max. Ripple and noise 5 Hz to 20 MHz (See Note 6) See table on page 2 Transient response 100 mV max. deviation (See Note 1) 150 μs recovery to within regulation band All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. SMT15C Data Sheet General Specifications Environmental Specifications Efficiency See Table below Thermal performance Operating ambient temperature -0 °C to +80 °C (See Note 10) Non-operating temperature -40 °C to +125 °C Switching frequency Fixed 200 kHz Protection Approvals and (See Note 4) TÜV Product Services standards EN60950, UL/cUL60950 Short-circuit Hiccup, non latching Material flammability UL94V-0 Recommended System Capacitance Weight 14.2 g (0.5 oz) Input capacitance (See Note 11) 270 μF / 20 mW ESR max. Coplanarity 150 μm Output capacitance (See Note 11) 680 μF / 10 mW MTBF Telcordia SR-332 7,817,294 hours ESR max. Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (12,13) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load SMT15C-05SADJJ 50 W 4.5 - 5.5 Vdc 0.9 - 3.3 V 0 A 15 A 89% ±0.2% ±0.5% SMT15C-12SADJJ 75W 10.2 - 13.8 Vdc 0.9 - 5.0 V 0 A 15 A 91% ±0.2% ±0.5% Part Number System with Options Product Family Rated Output Performance Input Voltage Number of Packaging Current Outputs Options SMT 15 C - 12 SADJ J 15 - 15 A C = Cost Optimized 05 = 4.5 - 5.5 Vdc SADJ = Single J = Pb free (RoHS SMT = Surface Mount 12 = 10.2 - 13.8 Vdc Adjustable Output 6/6 compliant) Notes: Output Voltage Adjustment 1. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.5 lo max. to 0.75 lo max. and voce versa The ultra-wide output voltage trim range offers major advantages to users 2. Measured with external filter. See Application Note 169 for details. who select the SMT15C series. It is no longer necessary to purchase a variety 3. Power up is the time from application of dc input to Power Good high. Remote ON/OFF asserted of modules in order to cover different output voltages. The output voltage can high to Power Good high. be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SMT15C series 4. This product is only for inclusion by professional installers within other equipment and must not be converter leaves the factory the output has been adjusted to the default operated as a stand-alone product. voltage of 0.9 V. 5. Reserved. 6. Measured as per recommended set-up. Cin = 270 μF (20 mW ESR max.). Cout = 680 μF (10 mW ESR max.). 7. Uses external resistor from TRIM to ground. Seee Application Note 169 for details. Minimum values Ripple and Noise Specification 485 μF for 5 V model, 280 μF for 12 V model. Model Output Voltage Pk - Pk RMS 8 Signal line assumed <3 m. 5 V input models 0.9 - 2.5 Vdc 30 mV 15 mV 9. External input fusing recommended. 3.3 Vdc 40 mV 15 mV 10. See Application Note 169 for operation above 50 ºC. 12 V input models 0.9 - 2.5 Vdc 50 mV 25 mV 11. See Application Note 160 for more details. 3.3 Vdc 50 mV 25 mV 12. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. SMT15C Data Sheet Mechanical Drawings Mating Connectors 0.234 0.901 Pin Assignments (5.95) (22.88) 1.20 0.054 Pin Function PIN 8 (30.5) PIN 7 (1.38) 1 Vout 2 Vout 3 Power Good 4 Ground 5 Ground 6 Vin 7 Trim 8 Remote ON/OFF PIN 1 0.054 0.150 0.145 4X (1.38) (3.81) (3.68) PIN 6 0.940 (23.88) 0.062 (1.57) REF Seating Plane 8 X 0.105 0.011 (2.67) (0.27) TYP All dimensions in inches (mm) All tolerance ±0.010in (±0.25mm) unless otherwise stated WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SMT15C Series 06Apr2015 0.457 (11.61) Installed Ht. 1.10 (27.9) 0.29 (7.4 max) 0.956 (24.27)