ARTESYN SMT15E-05W3V3J

POWER SMT15E Series Data Sheet Non-Isolated DC-DC Converter Total Power: 41.25 Watts Input Voltage: 3.0 - 5.5 Vdc # of Outputs: Single SPECIAL FEATURES ƒ 15 A current rating ƒ Input voltage range: 3.0 - 5.5 Vdc ƒ Output voltage range: 0.8 - 3.63 V ƒ Ultra high efficiency: 96% @ 5 Vin Electrical Specifications and 3.3 Vout Input ƒ Extremely low internal power Input voltage ra nge 3.0 - 5.5 Vdc dissipation Input current No load 70 mA typical ƒ Minimal thermal design concerns Input current (max.) 11.8 A max. @ lo max. ƒ Designed-in reliability: MTBF of 7 and Vout = 3.63 V million hours per Telcordia SR-332 Input reflected ripple 110 mA rms ƒ Ideal solution where board space is Remote ON/OFF See Note 2 at a premium or tighter card pitch is required Start-up time <20 ms ƒ Industry standard surface-mount Output footprint Voltage adjustability Fixed output versions ±10% (See Note 1) Wide trim version 0.8 - 3.63 Vdc ƒ Available RoHS compliant Setpoint accuracy ±0.4% ƒ Two year warranty Line regulation ±0.2% SAFETY Load regulation ±0.5% ƒ UL, cUL CAN/CSA 22.2 Minimum load 0 A No. E174104 Overshoot/Undershoot None ƒ UL 60690 File No. E174104 Ripple and noise 0 - 20 MHz BW 60 mV pk-pk 25 mV rms max. ƒ TÜV Product Service (EN60950:2000) Temperature coefficient ±0.01% / °C ƒ Certificate No. B 03 10 38572 Transient response 60 mV max. deviation 150 μs recovery to within ±1.0% ƒ CB report and certificate to Remote sense 10% Vo compensation DE3-51686M1 All specifications are typical at nominal input, full load at 25°C unless otherwise stated. SMT15E Data Sheet General Specifications Environmental Specifications Efficiency See Table below Thermal performance Operating ambient temperature -0 °C to +100 °C (See Note 3) Non-operating temperature -40 °C to +125 °C Insulation voltage Non-isolated Protection Switching frequency Fixed 300 kHz Short-circuit Continuous Approvals and EN60950 standards UL/cUL60950 Thermal Automatic recovery Material flammability UL94V-0 Dimensions L x W x H 33.02 x 13.46 x 8.21 mm EMC Characteristics 1.3 x 0.53 x 0.323 inches Electrostatic discharge EN61000-4-2, IEC801-2 Weight 6.3 g (0.22 oz) Conducted immunity EN61000-4-6 Coplanarity 100 μm Radiated immunity EN61000-4-3 MTBF Telcordia SR-332 7,042,000 hours MIL-HDBK-217F 680,000 hours Ordering Information Regulation Model Output Power Input Output Output Current Output Current Efficiency (5) Number (Max.) Voltage Voltage (Min.) (Max.) (Typical) Line Load (4) SMT15E-05W3V3J 54.45 W 3.0 - 5.5 Vdc 0.8 - 3.63 V 0 A 15 A 95% ±0.2% ±1.0% Part Number System with Options Product Family Rated Output Performance Input Voltage Type of Output Output Voltage Packaging (5) Current Options SMT 15 E - 05 W - V J SMT - Surface Mount 15 = 15 Amps E = Enhanced 05 = 3.0 - 5.5 Vdc W = Wide 0.8 - 3.63 Vdc No “-T’ sufffix = performance Pb-free (RoHS 6/6 compliant) in trays Notes: Output Voltage Adjustment 1. When Vin ≥ 4.5 V, then Vout can be adjusted from 0.8 Vdc to 3.63 Vdc. The ultra-wide output voltage trim range offers major advantages to users When Vin < 4.5 V, then Vout can be adjusted from 0.8 Vdc to 2.75 Vdc. who select the SMT15E-05W3V3J. It is no longer necessary to purchase a 2. The SMT15E features a ‘Negative Logic’ Remote ON/OFF operation. If not using the Remote ON/ variety of modules in order to cover different output voltages. The output OFF pin, leave the pin open (the converter will be on). The Remote ON/OFF pin is referenced to voltage can be trimmed in a range of 0.8 Vdc to 3.63 Vdc. When the ground. The following conditions apply for the SMT15E: SMT15E-05W3V3J converter leaves the factory the output has been adjusted Configuration Converter Operation to the default voltage of 3.3 V. Remote pin open circuit Unit is ON Remote pin pulled low Unit is ON • When Vin ≥ 4.5 V, then Vout can be adjusted from 0.8 Vdc to 3.6 Vdc Remote pin pulled high [Von/off >1.2 V] Unit is OFF • When Vin < 4.5 V, then Vout can be adjusted from 0.8 Vdc to 2.75 Vdc 3. Full derating curves available in both the Longform Datasheet and Application Note 136. 4. When the unit is trimmed down to 0.8 V, the efficiency is 82.5%. 5. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. SMT15E Data Sheet Mechanical Drawings Mating Connectors TOP VIEW Pin Assignments Pin Function 0.039 (1.00) 1 Remote ON/OFF 0.039 (1.00) 2 Remote Sense + 3 Trim 4 +Vout BOTTOM VIEW 5 Ground 0.190 6 +Vin 0.310 0.190 (4.83) (7.87) (4.83) 0.190 1.300±0.010 (33.02 ±0.25) 0.297 (4.83) (7.54) 5 4 3 2 1 6 SIDE VIEW 0.048 (1.22) 0.007 (0.18) Min Clearance Seating Plane Max. component Connector (6PL) All dimensions in inches (mm) Width :0.112 ± 0.003 (2.84 ± 0.08) All tolerance ±0.010in (±0.25mm) Length: 0.062 ± 0.002 (1.57 ± 0.04) unless otherwise stated WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. SMT15E_5_Series 06Apr2015 0.323 (8.21) Installed Ht. 0.530 ±0.010 (13.46 ± 0.25) 0.430 (10.92) 0.405 (10.29) 0.075 (1.91)