ARTESYN SMT20C2-00SADJJ

SIL/SMT20C2 Series 4.5 Vin to 13.8 V Single Output August 27, 2008 DC-DC CONVERTERS C Class Non-isolated 1 • 20 A current rating NEW Product • Input voltage range: 4.5-13.8 V • Output voltage: 0.59-5.1 V • Industry leading value • Cost optimized design • Excellent transient response • Output enable • Output voltage adjustability • Pathway for future upgrades • Supports silicon voltage migration • Resulting in reduced design-in and qual time • Current sink capability • RoHS compliant The SIL/SMT20C2 series is a new high density, open frame, non-isolated converter for space sensitive applications. This model has a wide input range (4.5-13.8 Vdc) and offers a wide 0.59-5.1 V output voltage range with 20 A load capability. An external resistor adjusts the output voltage from its pre-set value of 0.59 V to any value up to the 5 V maximum. Typical efficiencies for the models are 93% for the 12 V input version. The series offers remote ON/ 2 YEAR WARRANTY OFF and over-current protection as standard. All specifications are typical at nominal input, full load at 25 °C, unless otherwise stated SPECIFICATIONS GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Output voltage (See Note 5) 0.59-5.1 V Efficiency Vin=5 V, Vo=2.5 V, lo=20 A 90% Output setpoint 0.1% trim resistors ±1.0% Switching frequency Fixed 750 kHz accuracy Approvals and EN60950 standards (pending) UL/cUL6950 Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% Material flammability UL94V-0 Weight 8.50 g/0.3 oz. Min/max load 0 A/20 A MTBF 12 V @ 40 °C 6,721,853 hours Overshoot At turn-on 0.5% max. 100% load Undershoot At turn-off 100 mV max. Bellcore 332 Ripple and noise (See Note 1) 30 mV Coplanarity 150 μm 5 Hz to 20 MHz Vin = 5 V, Vout = 2.5 V Transient response (See Notes 1, 2) 130 mV max. deviation 50 μs recovery within ENVIRONMENTAL SPECIFICATIONS regulation band Thermal performance Operating ambient, 0 °C to +70 °C INPUT SPECIFICATIONS (See Note 5) temperature Non-operating -40 °C to +125 °C Input voltage range 4.5-13.8 Vdc Input current Minimum load 50 mA PROTECTION Remote OFF 5 mA Short-circuit Hiccup, non-latching Input current (max.) (See Note 3) 18 A @ Io max. Overvoltage protection Hiccup, non-latching Start-up time Remote ON/OFF 3 ms RECOMMENDED SYSTEM CAPACITANCE Input capacitance (See Note 6) 0 μF Output capacitance (See Note 7) 0 μF International Safety Standard Approvals UL/cUL CAN/CSA 22.2 TÜV Product Service (EN60950) CB report and certiŢ cate to IEC60950 File Name: sil/smt20c2.pdf Rev: 27 Aug 2008 SIL/SMT20C2 Series 4.5 Vin to 13.8 V Single Output August 27, 2008 DC-DC CONVERTERS C Class Non-isolated 2 For the most current data and application support visit www.powerconversion.com/products/ NEW Product OUTPUT OUTPUT OUTPUT REGULATION INPUT OUTPUT EFFICIENCY MODEL POWER MOUNT CURRENT CURRENT (8, 9) VOLTAGE VOLTAGE (TYP.) NUMBER LINE LOAD (MAX.) (MIN.) (MAX.) 100 W 4.5-13.8 Vdc Horizontal 0.59-5.1 V 0 A 20 A 93% ±0.2% ±0.5% SIL20C2-00SADJ-HJ 100 W 4.5-13.8 Vdc Vertical 0.59-5.1 V 0 A 20 A 93% ±0.2% ±0.5% SIL20C2-00SADJ-VJ 100 W 4.5-13.8 Vdc Horizontal 0.59-5.1 V 0 A 20 A 93% ±0.2% ±0.5% SMT20C2-00SADJJ Surface Part Number System with Options SXX20C2-00SADJ-VJ (8) RoHS Compliance Product Family J = Pb-free (RoHS 6/6 compliant) SMT = Surface Mount SIL = Single In Line Mounting Option Rated Output Current -V = Vertical 06 = 6 A -H = Horizontal 15 = 15 A Blank = Horizontal Surface 20 = 20 A 30 = 30 A Output Voltage 40 = 40 A Single Adjustable Output Performance Input Voltage C = Cost Optimized 00 = 4.5-13.8 V Generation Blank = Standard Part 2 = Increased Current Density Output Voltage Adjustment of the SIL/SMT20C2 Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL/SMT20C2. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59-5.1 V. When the SIL/SMT20C2 converter leaves the factory, the ouput has been adjusted to the default voltage of 0.59 V. Notes Power Good 1 Measured as per recommended system capacitance. 2 di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. 3 External input fusing is recommended. 4 Additional part numbers may be available with different output 4 V 1 out voltages. Enable 5 5 Airflow dependent, 100 LFM minimum required. +R 7 sense 6 No capacitor needed for ripple current capability. SIL20C2 7 No capacitor needed for stability. 8 TSE RoHS 5/6 (non Pb-free) compliant versions may be available R C on special request, please contact your local sales representative V out in L 6 for details. 3 2 8 O 9 NOTICE: Some models may not support all options. Please A D contact your local Emerson Network Power representative or use C in the on-line model number search tool at R trim http://www.powerconversion.com to find a suitable alternative. (for trim -R sense down) GND Figure 1: Standard Application Drawing File Name: sil/smt20c2.pdf Rev: 27 Aug 2008 SIL/SMT20C2 Series 4.5 Vin to 13.8 V Single Output August 27, 2008 DC-DC CONVERTERS C Class Non-isolated 3 For the most current data and application support visit www.powerconversion.com/products/ NEW Product PIN CONNECTIONS PIN NO. FUNCTION 0.462 (11.73) 1 Vout 1.200 (30.48) 0.295 (7.49) 2 Trim 0.062 (1.57) PCB REF 0.105 (2.67) 3 Ground 0.610 (15.49) 4 Power good 5 Enable 0.150 (3.81) TYP PIN 8 PIN 1 6Vin 0.050 (1.27) REF 7 Remote Sense (+) 0.025 (0.64) ±.001 8 Remote Sense (-) SQ PIN TYP 8 PLACES Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Figure 2: Vertical Mount Mechanical Drawing 0.482 (12.24) 0.295 (7.49) 0.025 (0.64) ±.001 1.200 (30.48) SQ PINS TYP 0.062 (1.57) REF PIN 9 9 PLACES 0.535 (13.59) 0.610 (15.49) 0.040 (1.02) REF PIN 1 0.120 (3.05) TYP 0.125 (3.18) TYP Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Figure 3: Horizontal Mount Mechanical Drawing File Name: sil/smt20c2.pdf Rev: 27 Aug 2008 0.000 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) 1.165 (29.59) 0 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) SIL/SMT20C2 Series 4.5 Vin to 13.8 V Single Output August 27, 2008 DC-DC CONVERTERS C Class Non-isolated 4 For the most current data and application support visit www.powerconversion.com/products/ NEW Product PIN CONNECTIONS 1.200 (30.48) 0.065 (1.65) 0.015 (0.38) PIN NO. FUNCTION PIN 8 1 Vout PIN 1 0.610 (15.49) 2 Trim 0.535 (13.59) 3 Ground PIN 10 PIN 9 4 Power good 5 Enable 0.025 (0.64) ±.002 0.482 (12.24) 6Vin PIN WIDTH TYP 0.295 (7.49) 7 Remote Sense (+) 0.062 (1.57) PCB REF 8 Remote Sense (-) 9 *Mech Support 0.040 (1.02) 10 *Mech Support Dimensions in Inches (mm) Tolerances (unless otherwise specified) * Horizontal version only 2 Places ±0.030 (±0.76) 0.125 (3.18) TYP 3 Places ±0.010 (±0.25) Figure 4: Surface Mount Mechanical Drawing Datasheet © Emerson™ 2008 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Emerson Network Power accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 3Application Note 3Longform Datasheet powerconversion.com File Name: sil/smt20c2.pdf Rev: 27 Aug 2008 0 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.48) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21)