ELECTRICAL SPECIFICATIONS OPTICAL ISOLATOR POWER: The optical isolator can accommodate standard operating ELECTRONIC MODULE voltages from 5 to 28 VDC. It should never be connected directly to AC power mains. The module draws approximately 75 mA and a green LED indicates the unit is powered. The optical isolator module does not provide power to the encoder. Any encoders used in conjunction with this module must be connected to their own power. SIGNAL: Specifying an optical isolator module requires knowledge of three system parameters: the DC supply voltage available in the system; the encoder output type (logic levels and driver type); and the input signal specifications of the receiving electronics. MECHANICAL SPECIFICATIONS Package dimensions are 114.4 mm high by 99 mm wide by 22.5 mm thick. The package mounts to a DIN rail type EN 50 022 (35mm X 7.5mm). A length of DIN rail is supplied with each module. The module simply snaps directly to the DIN rail and is ready to use. 22.5 mm This is a versatile interface between an incremental 114.5 mm (0.89 inches) (4.51 inches) encoder and receiving electronics. It accepts single ended or differential inputs and provides single ended or differential outputs in either an open collector or line driver configuration. It accommodates all standard operating voltages from 5 to 28 VDC. Up to eight Optical 99 mm Isolator Modules can be daisy-chained to provide multiple, simultaneous outputs to controllers or PLC’s. This Optical Isolator can help clean up noisy signals by converting to a different line driver output. It has a 1 MHz throughput capability and can be used wherever a fast, optically isolated interface is required. Output Code Format Dual Channel in quadrature plus index and complements. Data lines are designated A, B, Z, A/, B/, Z/ at the From Encoder module Differential line driver (Use Connection Instructions #1) Single ended line driver (Use Connection Instructions #2) Output Signal Type From Encoder Single ended open collector with pull-up resistors internal to encoder (Use Connection Instructions #3) Single ended, open collector (Use Connection Instructions #3) Output Signal 5 VDC (TTL, RS422 compatible, line driver) Voltage Level From 12-15 VDC Encoder 24VDC Frequency Response 1 MHz, maximum of Optical Isolator Power Requirements 5-28 VDC ±5%, 75mA plus load current For Optical Isolator 28V/V Line Driver, 100mA source/sink, Vout = Vin Optical Isolator 28V/5 Line Driver, 100mA source/sink, Vout = 5V (Derate output current to 50mA with supply voltage > 12VDC) Output Options 28V/OC NPN Open Collector, 80mA sink Protection Level Supply lines protected against over voltage to 60 volts and reverse voltage Tristate Outputs Available as –S Special Feature Tel: 805-968-0782/800-350-2727 | Fax: 805-968-3154/ 800-960-2726 | 7230 Hollister Ave, Goleta, CA 93117-2807| www.beisensors.com Specification No. 02125-001 Rev 0713 CONNECTION INSTRUCTIONS #1 Differential Line Driver Encoder signals from 5 VDC to 24 VDC (must specify the voltage when ordering) This is the preferred type of encoder output as it has the best noise immunity. Connect each encoder signal to its like optical isolator input (A to A, A/ to A/, etc). Figure 1 Standard Connection to Optical Isolator Optical Isolator Module Z Z/ A A A No Connection A A/ A/ A/ No Connection A/ ENCODER B B B B B/ B/ B/ B/ B/ Z Z B CONTROLLER Z Z/ Z/ Z Z/ A/ Z/ VS REG Vs, 5V to 28V 0V 0V, Power Common +V +V A 0V 0V Encoder Differential Line Driver Output CONNECTION INSTRUCTIONS #2 Single Ended Line Driver Encoder signal from 5 VDC to 24 VDC (must specify the voltage when ordering) Connect encoder output A to optical isolator module input channel A, B to B and Z to Z. Connect the A/, B/, and Z/ inputs of the optical isolator to circuit common of the encoder supply. Single ended operation is limited to shorter cable runs and is more susceptible to noise. Figure 2 Connection Diagram Single Ended Line Driver Z Optical Isolator No Connection A A A No Connection A A/ A/ A/ Connect A/, B/, Z/ to Encoder Circuit B B Common B B B/ ENCODER B/ B/ Z Z B CONTROLLER Z Z/ Z/ Z VS Z/ REG A Vs, 5V to 28V 0V 0V, Power Common +V +V Encoder Supply 0V 0V Encoder Single Ended Line Driver Output Tel: 805-968-0782/800-350-2727 | Fax: 805-968-3154/ 800-960-2726 | 7230 Hollister Ave, Goleta, CA 93117-2807| www.beisensors.com Specification No. 02125-001 Rev 0713 CONNECTION INSTRUCTIONS #3 Open Collector with or without Internal Pull-up Resistors Encoder NPN (sinking) outputs. Connect encoder output A to optical isolator module input A/, B to B/ and Z to Z/. Connect the A, B, and Z inputs of the optical isolator to the auxiliary output terminal on the optical isolator module for 5V module and to higher voltage when specified by module model and part number. This connection results in a logic inversion within the optical isolator module. To compensate for the logic reversal, swap A for A/, B for B/, and Z for Z/ at the optical isolator outputs. Z Figure 3 +5 Output Connection Diagram A/ Open Collector to Optical Module Optical Isolator Encoder Circuit A Common A A B/ A/ A or A/ A/ ENCODER B B B B CONTROLLER B/ B or B/ B/ Z/ Z Z Z A Z/ Z/ Z or Z/ Vs, 5V to 28V VS REG AUX 5V 0V, Power Common 0V +V +V To 5 AUX for 5V module. Optical Regulation To 12-15 for 24V dependent Power Supply on specified module input 0V 0V Encoder Open Collector Output voltage. Uses for Optical Isolator Module Example 1: Resolve an electrical conflict between encoder output and receiving electronics Sometimes system constraints result in an incompatibility between the encoder output and the receiving electronics or the cabling. A typical symptom of this problem is missed or intermittent counts. As an example, a single-ended TTL receiver that is more than 20 feet from the encoder may not be able to compensate for the signal attenuation and ringing caused by the encoder cabling. An optical isolator module installed near the receiver as shown in Figure 4 can receive the signal, rejecting the cable effects and produce a signal compatible with the input device. Optical TTL Isolator Single-Ended Module Receiver > 20’ < 6’ FIGURE 4 LONG CABLE RUN TO SINGLE ENDED INPUT Tel: 805-968-0782/800-350-2727 | Fax: 805-968-3154/ 800-960-2726 | 7230 Hollister Ave, Goleta, CA 93117-2807| www.beisensors.com Specification No. 02125-001 Rev 0713 Example 2: Signal Splitter The optical isolator can be used to connect a single encoder to multiple devices. Optical isolator can be used to split an encoder output to drive up the 8 devices as shown in Figure 5. One optical isolator module is used to drive each receiver. Optical isolator modules can be specified with outputs to match receiver inputs; i.e. an encoder signal can be split to drive a differential TTL input with one module, a 12 V line driver with another module and provide an open collector, NPN signal with another module. * Also see the BEI Encoder Signal Broadcaster Module on page 5 for this application* FIGURE 5 CONNECTION DIAGRAM FOR M ULTIPLE, 24V Supply NON- C OMPATIBLE RECEIVERS Opto Isolator 24V Logic 60001- 003 12V Supply Encoder Opto Isolator Supply V 12V Logic 60001- 003 5V Logic 5V Supply Opto Isolator 5V Logic Line Driver 60001- 003 5V Output 24V Supply Opto Isolator 5V Logic 60001- 002 Maximum of 8 Optical Isolator Modules Example 3: Repeater On extremely long cable runs (greater than 500 feet), an optical isolator module may be needed as a mid- point repeater to receive, amplify and re-broadcast the signal. An example is illustrated in Figure 6. FIGURE 6 REPEATER FOR VERY LONG CABLE RUNS Optical Isolator PLC Module 500’ 500’ Tel: 805-968-0782/800-350-2727 | Fax: 805-968-3154/ 800-960-2726 | 7230 Hollister Ave, Goleta, CA 93117-2807| www.beisensors.com Specification No. 02125-001 Rev 0713 Optical Isolator Selection Table To find the correct optical isolator for your application, look in column 1 for the logic voltage of your encoder. Then choose the correct row in column 2 that describes the type of output from the isolator that is compatible with your receiving electronics. Read across to columns 3 and 4 to find the module and part number of the correct optical isolator. (1) (2) Encoder Output Optical Isolator (3) (4) Logic Level Output Logic Level Model Number Part Number Voltage Voltage Vout = Vin EM-DR1-IC-5-TB-28V/V 60001-003 5V Vout = 5V EM-DR1-IC-5-TB-28V/5 60001-002 Vout = OC EM-DR1-IC-5-TB-28V/OC 60001-004 Vout = Vin EM-DR1-IC-15-TB-28V/V 60001-008 12-15V Vout = 5V EM-DR1-IC-15-TB-28V/5 60001-012 Vout = OC EM-DR1-IC-15-TB-28V/OC 60001-014 Vout = Vin EM-DR1-IC-24-TB-28V/V 60001-010 24V Vout = 5V EM-DR1-IC-24-TB-28V/5 60001-011 Vout = OC EM-DR1-IC-24-TB-28V/OC 60001-013 Additional Modules and Accessories ENCODER SIGNAL BROADCASTER MODULE Accepts standard incremental encoder inputs and can broadcast up to four encoder signals to four independent devices. Each of the broadcast signals are optically isolated eliminating ground loops. POWER SUPPLY With a wide range of acceptable input voltages (AC and DC) this DIN Rail mountable power supply is usable in virtually all industrial applications worldwide. It has built in surge protection to reduce faults due to transients and it has 100% reserve capacity for startup and overload conditions. CABLE AND CABLE ASSEMBLIES Cable reels for your own custom wiring requirements or cable assemblies are available, using high quality custom BEI standard cable consisting of four, low capacitance shielded twisted pairs with an overall shield, extra large conductors for power, and signal ground; all within an abrasion-resistant PVC jacket. Cable Reels 100 ft. reel Part No. 37048-003-100 500 ft. reel Part No. 37048-003-500 Cable Assemblies Part Nos. for MS3106F14S-6S Mating Connector 10 ft. # 31186-1410 │ 20 ft. # 31186-1420 │30ft. # 31186-1430 Part Nos. for MS3106F16S-1S Mating Connector 10 ft. # 31186-1610 │ 20 ft. # 31186-1620 │30ft. # 31186-1630 Part Nos. for MS3106F18S-1S Mating Connector 10 ft. # 31186-1810 │ 20 ft. # 31186-1820 │30ft. # 31186-1830 Tel: 805-968-0782/800-350-2727 | Fax: 805-968-3154/ 800-960-2726 | 7230 Hollister Ave, Goleta, CA 93117-2807| www.beisensors.com Specification No. 02125-001 Rev 0713