Manufacturers
C&K BD08AV
Description
Switch DIP OFF ON SPST 8 Extended Slide 0.1A 25VDC PC Pins 10000Cycles/SwitchCycles 2.54mm Thru-Hole Tube
BD08AV
Part Number
BD08AV
Price
Request Quote
Manufacturer
C&K
Lead Time
Request Quote
Category
Switches » Switch DIP
Specifications
Manufacturer
C&K
Manufacturers Part #
BD08AV
Lead Time
13 Week Lead Time
Industry Aliases
BD08AV
Sub-Category
DIP Switches
Series
BD
Factory Pack Quantity
23
Datasheet
Extracted Text
BD Series Standard Profile DIP Switches Features/Benefits Typical Applications • Traditional full profile DIP switch • Address switch for industrial controls • Extended actuator for easy actuation • Logic switching for computers and peripherals • Open bottom construction allows for • Function controlling for H solder washing without the need numerous applications for tape seal • RoHS compliant Specifications VIBRATION: No contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in DA or 5g, which- SWITCH FUNCTION: SPST - 1 thru 12 position available ever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. (except 11 position). SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CONTACT RATING: PACKAGING: Switches supplied in rigid dispensing tubes in full-tube Carry: 100 mA max. @ 50 V DC. quantities only: this may effect order quantity. Number of switches Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC. per tube varies with model. Switch position 1 denotes pin number MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break 1. All switch actuators in ‘OFF’ position, standard. cycles at full load, each circuit. CONTACT RESISTANCE: Below 50 milliohms typ. initial Materials @ 2-4 V DC 100mA. CASE & COVER: Glass filled polyester (PBT), 9 INSULATION RESISTANCE: 10 ohms min. flame retardant (UL 94V-0). DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between ACTUATOR: Glass filled nylon 6/6, flame retardant, adjacent terminals. heat stabilized (UL 94V-0) CAPACITANCE: 5pF max. between adjacent terminals. CONTACTS: Gold over nickel over phosphor bronze. STORAGE & OPERATING TEMPERATURE: -40°C to 85°C. TERMINALS: Matte-tin over nickel over phosphor bronze. SHOCK: Withstands 20g 11 ms sawtooth waveform with no con- tact opening greater than 10 microseconds. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Vertical Full Profile DIP QUANTITY PART NUMBER NO.POS. DIM. ‘A’ DIM. ‘B’ PER TUBE .062 Ø.038 TYP. BD01 1 .180 (4,57) NA 115 (0,97) (1,58) MAX BD02 2 .280 (7,11) .100 (2,54) 74 .100 TYP. ACTUATOR DIM 'A' (2,54) BD03 3 .380 (9,65) .200 (5,08) 54 TRAVEL ON BD04 4 .480 (12,19) .300 (7,62) 43 .380 BD05 5 .580 (14,73) .400 (10,16) 35 .297 (9,65) (7,55) BD06 6 .680 (17,27) .500 (12,75) 30 BD08 1 2 34567 8 BD07 7 .780 (19,81) .600 (15,24) 26 .160 TYP. BD08 8 .880 (22,35) .700 (17,78) 23 DIM 'B' (4,06) BD09 9 .980 (24,89) .800 (20,32) 21 .059 TYP. (1,5) .080 TYP. BD10 10 1.080 (27,43) .900 (22,.86) 19 (2,03) BD12 12 1.280 (32,51) 1.100 (27,94) 16 .265 .032 Schematic .030 (6,73) (0,82) (0,77) TYP. SPST .006 .089 .020 TYP. .100 TYP. (0,16) .297 (2,26) (0,51) (2,54) (7,55) .141 TYP. (3,58) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com H–16 DIP DIP BD Series Standard Profile DIP Switches Open Base and AV Right Angle Terminal Style 0.050 .089 (1,27) (2,26) QUANTITY 0.030 PART NUMBER NO.POS. DIM. ‘A’ PER TUBE (0,77) H BD02AV 2 .280 (7,11) 72 0.297 (7,55) BD03AV 3 .380 (9,65) 52 BD08AV BD04AV 4 .480 (12,19) 42 0.061 TYP. .032 BD05AV 5 .580 (14,73) 35 (1,55) (0,82) BD06AV 6 .680 (17,27) 29 TYP. DIM.A BD07AV 7 .780 (19,81) 26 ON BD08AV 8 .880 (22,35) 23 .080 .380 BD09AV 9 .980 (24,89) 20 (2,03) (9,65) BD10AV 10 1.080 (27,43) 18 .125 1 2 3 4 5 6 7 8 BD12AV 12 1.280 (32,51) 15 (3,18) Schematic .020 TYP. .010 (0,51) .100 TYP. (0,25) .006 (2,54) (0,16) .100 .320 .100 (2,54) SPST (8,12) (2,54) .100 TYP. .046 DIA TYP. (2,54) (1,17ø) Installation, Soldering and Cleaning All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: 1) Wave soldering recommended at 500° F (260ºC) solder temperature. 2) Hand solder using 30 watt small tip iron controlled at 500° F (260ºC), 10 seconds max./terminal. 3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com H–17
Frequently asked questions
How does Electronics Finder differ from its competitors?
Is there a warranty for the BD08AV?
Which carrier will Electronics Finder use to ship my parts?
Can I buy parts from Electronics Finder if I am outside the USA?
Which payment methods does Electronics Finder accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Request a Quote
The quote request has been received
Close
Facing challenges or have inquiries? Feel free to contact us!
Call Us +1-469-283-2440
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods