C&K HBS4KGB4ST011C
Specifications
Manufacturer
C&K
Manufacturers Part #
HBS4KGB4ST011C
Lead Time
10 Week Lead Time
Industry Aliases
HB-S-4-KG-B4-S-T0-11-C
Sub-Category
Snap Action Switches
Series
HB
Factory Pack Quantity
1
Datasheet
hb.pdf
483 KiB
Extracted Text
Snap-acting HB Series Single Pole Standard Precision Snap-acting Switches Features/Benefits Typical Applications • Low differential travel, high repeatability • Thermostats • Long life—150,000 cycles typical • Motors • Single and double pole circuitry • Industrial controls • Sealed actuator and case Specifications Materials CONTACT RATING: From low level* to 20 AMPS @ 480 V AC; SWITCH HOUSING: Heat resistant/electrical grade phenolic. see ELECTRICAL RATING option section for complete listings. INSERTS: Brass alloy. ELECTRICAL LIFE: 150,000 cycles at 20 AMPS @ 250 V AC. ACTUATOR BUTTON: Moisture resistant phenolic. consult Customer Service Center for typical life at other ratings. SPRING: Copper alloy. INSULATION RESISTANCE: 1,000 M ohm min. PIVOT: Brass alloy. DIELECTRIC STRENGTH: 1,500 Vrms min. @ sea level. MOVABLE CONTACTS: Gold alloy for ratings 1 AMP or less. OPERATING TEMPERATURE: –67ºF to 302ºF (–55ºC to 150ºC). Fine silver for ratings greater than 1 AMP and motor load OPERATING FORCE: From 4 oz. to 26 oz. max. at actuator ratings less than 1/2 HP @ 125 V AC. Silver alloy for motor button available. load ratings 1/2 HP @ 125 V AC or greater. MOUNTING SCREWS: Torque 3 in/lbs max. STATIONARY CONTACTS: Gold alloy for ratings 1 AMP or less. J (Note: Exceeding 3 in/lbs torque may change operating Fine silver welded to copper base for ratings greater than characteristics and increase the possibility of cracking 1 AMP and motor load ratings less than 1/2 HP @ 125 V AC. switch case). Silver alloy on copper base for motor load ratings 1/2 HP @ 125 V AC or greater. TERMINAL SCREWS: Torque 4 in/lbs max. TERMINALS: Brass alloy, bright tin plated. PANEL MOUNTING BUSHING: Torque 4-6 in/lbs max. DEGREE OF PROTECTION: IP65; Dust-proof, water splash and NOTE: Specifications and materials listed above are for switches with standard options. dew condensation. For information on specific and custom switches, consult Customer Service Center. * Low Level=conditions where no arcing occurs during switching, i.e., 0.4 VA max. @ 20 V AC or DC max. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages J-72 through J-76. For additional options not shown in catalog, consult Customer Service Center. H B S S C Series HB Precision Snap-acting Switches Operating Force KG 18 oz./510 grams Mounting Style Circuitry Function GF 4 oz./113 grams S Standard C SPDT S SP KA 9 oz./255 grams Contact Separation KC 13 oz./368 grams 2 .020” KH 20 oz./567 grams 1 .010” PB 26 oz./737 grams 4 .040” 7 .070” Electrical Rating B4 20 A, 125, 250, 480 V AC; Actuator 0.25 A, 250 V DC; 0.5 A, 125 V DC P0 Pin plunger A2 5 A, 125, 250 V AC A0 Lever roller Terminations B6 20 A, 125, 250, 480 V AC; 0.25 A, D0 Stub plunger 11 Flat base, solder, 4-40 screws 250 V DC; 0.5 A, 125 V DC; 3/4 HP, F0 Reverse acting lever roller 41 Flat base, .250” quick connect 125 V AC; 1 1/2 HP, 25O V AC J0 High overtravel plunger 55 Step base, cup washers, 6-32 screws F5 1 A,125 V AC; 1 A, 3O V DC R5 Perpendicular roller plunger F9 22 A, 125, 277 V AC; 15 A, 480 V AC; T0 Lever 1/4 HP, 125 V AC; 1/2 HP, 250 V AC TS Sealed Lever Y0 Reverse acting lever Dimensions are shown: mm Specifications and dimensions subject to change www.ckswitches.com J–71 HB Series Single Pole Standard Precision Snap-acting Switches Sealed Actuator and Case To provide reliable service under environmental conditions that might damage standard precision switches, various HB Series switch models are sealed against the entrance of airborne contaminants and/or splashing liquids. The clearance between the operating plunger and the cover is sealed with a silicone boot and the base cover joint is sealed with an epoxy adhesive. These models are designed to meet requirements of IP65 (dust proof, water splash and dew condensation). For additional information on sealed switches, consult our Customer Service Center. SERIES HB PRECISION SNAP-ACTING SWITCHES FUNCTION S SINGLE POLE SWITCH OPER. POS. .625 ± .015 J (15,88 ± 0,38) Single Pole NOTE: To select switching function, see CIRCUITRY section, page J-52. CONTACT SEPARATION DIFFERENTIAL TRAVEL SPECIFICATION LIMITS OPTION NOMINAL CONTACT .0004 FOR VARIOUS CONTACT SEPARATIONS CODE SEPARATION (in./mm) .0002 INCH .020 2 CONTACT (0,51) Switches with 1 AMP rating (option 0 .001 .002 .003 .004 .005 SEPARATION code ‘F5’) are available only with .010 1 .020 contact separation (option ‘2’). (0,25) 1 Switches with 1/2 HP, 125 V AC rating .040 or greater (option codes ‘B5 and B6’) 4 2 (1,02) are not available with .010 contact separation (option code ‘1’). .070 4 7 (1,78) 7 .0015 Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com J–72 Snap-acting Snap-acting HB Series Single Pole Standard Precision Snap-acting Switches OPERATING FORCE OPERATING FORCE SPECIFICATION LIMITS FOR VARIOUS CONTACT SEPARATIONS OPTION MAXIMUM OPERATING STANDARD CONTACT CODE FORCE (OZ./GRAMS) SEPARATION (inch) OUNCES CONTACT 18 KG .020 SEPARATION 510 41 79 13 14 8 20 26 30 4 .010 .010 GF 115 .020 9 .010 KA 255 .040 13 .020 KC 370 .070 20 KH .040 STANDARD RANGE MAXIMUM LIMITS AVAILABLE 570 26 .070 PB 740 NOTE: All listed differential travel characteristics are based on standard operating force andcontact separation. For any other force or contact separation, consult Customer Service Center. Operating force varies with actuator option, see ACTUATOR option section. ELECTRICAL RATING OPTION CODE MOVABLE CONTACT STATIONARY CONTACT ELECTRICAL RATING J 20 AMPS @ 125, 250 & 480 V AC; 0.25 AMPS @ 250 V DC; 0.5 AMPS @ B4 Fine silver welded to 125 V DC (UL). Fine silver. copper base. A2 5 AMPS @ 125 & 250 V AC (UL). 20 AMPS @ 125, 250 & 480 V AC; 0.25 AMP @ 250 V DC; 0.5 AMP @ Precious metal alloy. B6 Precious metal alloy. 125 V DC; 3/4 HP @ 125 V AC; 1 1/2 HP @ 250 V AC (UL). F5 Gold alloy. Gold alloy. Low level* to 1 AMP @ 125 V AC; 1 AMP @ 30 V DC (UL). 22 AMPS @ 125 & 277 V AC; 15 AMPS @ 480 V AC; 1/4 HP @ 125 V AC; Fine silver welded to Fine silver. F9 1/2 HP @ 250 V AC; 277 V AC (UL). copper base. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definition and specifications. AVAILABLE COMBINATIONS OPERATING FORCE (oz.) ELECTRICAL 4 9 13 18 20 26 RATING GF KA KC KG KH PB A2 • • • • • • B4 x • • • • • x x x • • • B6 F5 x x • • • • F9 x x x • • • • AVAILABLE x NOT AVAILABLE All models with all options Consult Customer Service center for availability and delivery of nonstandard ratings. * Low Level=conditions where no arcing occurs during switching, i.e., 0.4 VA max. @ 20 V AC or DC max. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com J–73 HB Series Single Pole Standard Precision Snap-acting Switches MOUNTING STYLE S Standard NOTE: Mounting holes will accept pins or screws of .139 dia. (3,53) max. on NOTE: Torque mounting screws 3 inlbs max. 1.000 ± .002 (25,4 ± 0,05) centers. ACTUATOR A NO. D A D C OPTION CODE POLES FIG. DIM. A DIM. C DIM. B DIM. D C .86 1.120 ± .060 .38 dia. 1.03 SP 1 A0 (21,8) (28,45 ± 1,52) (9,7Ø) (26,2) .92 .844 ± .020 SP 3 — — B D0 B (23,4) (21,44 ± 0,51) .09 1.120 ± .050 .38 dia. .74 F0 SP 2 (2,3) (28,45 ± 1,27) (9,7Ø) (18,8) .86 .860±.030 SP 4 — — J J0 (21,8) (21,84±0,76) FIG. 1 FIG. 2 Lever Roller Lever Roller .92 .625 ± .010 SP 5 — — P0 (23,4) (15,88 ± 0,25) .92 .62 .50 dia. 0.61 A SP 6 R5 (23,4) (15,7) (12,7Ø) (15,5) 1.310 .720 ± .060 1.03 dia. T0 SP 7 — (33,27) (18,28 ± 1,52) (26,2Ø)) 1.47 .720 ± .060 1.03 dia. B TS* SP 7 — (37,3) (18,28 ± 1,52) (26,2Ø) .05 .720 ± .030 .74 dia. 2.65 SP 8 Y0 (1,3) (18,29 ± 0,76) (18,8Ø) (6,73) FIG. 3 Stub Plunger * Actuators sealed against the entrance of airborne C contaminants and/or splashing liquids. 0.33 A (8,40) Dia. A A B B D FIG. 5 PANEL MOUNTING Pin Plunger .640 ± .020 B FIG. 4 FIG. 6 Plunger Perpendicular Roller Plunger .50 DIA. (12,70?) D C A C A B B FIG. 8 FIG. 7 Reverse Acting Lever Lever Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ckswitches.com J–74 Snap-acting Snap-acting HB Series Single Pole Standard Precision Snap-acting Switches ACTUATOR ACTUATOR * SEALED ACTUATOR OPTION CODE A0 D0 F0 J0 P0 R5 T0 Y0 TS 4 GF — — — — — — — — 115 3 9.5 10 10 9 10 2 10 2 KA 85 269 284 284 255 284 60 284 56 MAXIMUM 13 10 13 13 13 10 KC — — — 370 284 370 370 370 284 OPERATING FORCE 3.5 18 2.5 2.5 KG — — — — — 100 510 71 71 (OZ./GRAMS) 4 20 20 20 20 20 3 20 3 KH 115 570 570 570 570 570 85 570 85 4.5 26 20 26 26 26 3.5 20 3.5 PB 130 740 570 740 740 740 100 570 100 1 GF — — — — — — — — 28 .75 4 3 4 4 4 .5 3 .5 KA 21 110 85 110 110 110 14 85 14 MINIMUM 1.7 4 3 4 4 4 3 KC — — 48 110 85 110 110 110 85 RELEASE FORCE .75 4 .5 .5 KG — — — — — 21 110 14 14 (OZ./GRAMS) .75 4 3 4 4 4 .5 3 .5 KH 21 110 85 110 110 110 14 85 14 J .75 4 3 4 4 4 .5 3 .5 PB 21 110 85 110 110 110 14 85 14 NOTE: For basic switch operating forces, see page J-71. * Actuators sealed against the entrance of airborne contaminants and/or splashing liquids. ACTUATOR * SEALED ACTUATOR OPTION CODE A0 D0 F0 J0 P0 R5 T0 Y0 TS .0005 GF — — — — — — — — (0,013) .020 .0005 .005 .0005 .047 .005 .047 KA — — (0,51) (0,013) (0,13) (0,013) (1,19) (0,13) (1,19) MAXIMUM .002 .008 .002 .009 KC — — — — — DIFFERENTIAL (0,05) (0,20) (0,05) (0,23) TRAVEL .062 .003 .078 .078 KG — — — — — (IN/MM) (1,57) (0,08) (1,98) (1,98) .080 .003 .020 .003 .093 .020 .093 KH — — (2,03) (0,76) (0,51) (0,08) (2,36) (0,51) (2,36) .125 .007 .030 .005 .156 .031 .156 PB — — (3,18) (0,18) (0,76) (0,13) (3,96) (0,79) (3,96) .020 GF — — — — — — — — (0,51) .312 .020 0.8 .015 .015 .015 .38 .09 .38 KA (7,92) (0,51) (2,0) (0,38) (0,38) (0,38) (9,7) (2,3) (9,7) .020 0.8 .020 .020 .020 .09 MAXIMUM KC — — — (0,51) (2,0) (0,51) (0,51) (0,51) (2,3) PRETRAVEL .312 .025 .38 .38 (IN/MM) KG — — — — — (7,92) (0,64) (9,7) (9,7) .38 .025 0.9 .025 .025 .025 .38 0.9 .38 KH (9,7) (0,64) (2,3) (0,64) (0,64) (0,64) (9,7) (2,3) (9,7) .38 .030 0.9 .030 .030 .030 .38 0.9 .38 PB (9,7) (0,76) (2,3) (0,76) (0,76) (0,76) (9,7) (2,3) (9,7) .005 GF — — — — — — — — (0,13) .156 .055 .06 .22 .005 .141 .19 .06 .19 KA (3,96) (1,40) (1,5) (5,6) (0,13) (3,58) (4,8) (1,5) (4,8) .055 0.9 .22 .005 .141 0.9 MINIMUM KC — — — (1,40) (2,3) (5,6) (0,13) (3,58) (2,3) OVERTRAVEL .156 .005 .19 .19 (IN/MM) KG — — — — — (3,96) (0,13) (4,8) (4,8) .156 .055 0.9 .22 .005 .141 .19 0.9 .19 KH (3,96) (1,40) (2,3) (5,6) (0,13) (3,58) (4,8) (2,3) (4,8) .156 .055 0.9 .22 .005 .141 .19 0.9 .19 PB (3,96) (1,40) (2,3) (5,6) (0,13) (3,58) (4,8) (2,3) (4,8) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com J–75 HB Series Single Pole Standard Precision Snap-acting Switches TERMINATIONS 11 FLAT BASE, SOLDER TERMINALS AND 4-40 SCREWS 41 FLAT BASE, .250” QUICK CONNECT TERMINALS NOTE: Switches with flat base option have molded ribs that provide increased creep distance. 55 STEP BASE, 6-32 SCREWS AND CUP WASHERS J NOTE: Switches with step base option provide wide electrical clearance for screw terminal options. CIRCUITRY C DT (Double Throw, Normally Closed & Normally Open) Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ckswitches.com J–76 Snap-acting
Frequently asked questions
How does Electronics Finder differ from its competitors?
Is there a warranty for the HBS4KGB4ST011C?
Which carrier will Electronics Finder use to ship my parts?
Can I buy parts from Electronics Finder if I am outside the USA?
Which payment methods does Electronics Finder accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Switch Snap Action N.O./N.C. DPDT Roller Lever Quick Connect 15A 250VAC 1118.55VA 1.67N Screw Mount ...
Switch Snap Action N.O./N.C. DPDT Roller Lever Quick Connect 15A 250VAC 1118.55VA 1.67N Screw Mount ...
Switch Snap Action N.O./N.C. DPDT Button Quick Connect 15A 250VAC 1118.55VA 8.34N Screw Mount Bulk A...
Switch Snap Action N.O./N.C. DPDT Lever Quick Connect 15A 250VAC 1118.55VA 1.67N Screw Mount Bulk AD...
Switch Snap Action N.O. DPST Lever Quick Connect 15A 250VAC 1118.55VA 1.67N Screw Mount Bulk ADPDC2T...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods