TS Series Tiny Slide Switches Features/Benefits Typical Applications • Reliable contact design ensures • Test & measurement equipment long electrical life • Computers & peripherals • Ratings up to 3 AMPS • Telecommunications & • Epoxy terminal-seal compatible networking equipment with bottom wash cleaning • RoHS compliant Models Available Specifications Materials CONTACT RATING: B contact material: 0.4 VA max. @ 20 V AC or CASE: Glass filled nylon 4/6, flame retardant, heat stabilized. I DC max. Q contact material (TS01 Model): 3 AMPS @ 120 V AC ACTUATOR: Nylon, black standard. or 28 V DC; (TS02, TS03 Models): 1 AMP @ 120 V AC or 28 V HOUSING: Stainless steel or stainless steel, nickel plated. DC. See page I-10 for additional ratings. END CONTACTS: B contact material: Copper alloy, with gold plate over ELECTRICAL LIFE: nickel plate. Q contact material: Coin silver, silver plated. See TS01 MODELS: 60,000 make-and-break cycles at full load. page I-10 for additional contact materials. TS02, TS03 MODELS: 30,000 cycles. CENTER CONTACT & ALL TERMINALS: B contact material: Copper CONTACT RESISTANCE: Below 20 m Ω typ. initial @ alloy, with gold plate over nickel plate. Q contact material: Copper 2-4 V DC, 100 mA, for both silver and gold plated contacts. alloy, silver plated. See page I-10 for additional contact materials. 9 INSULATION RESISTANCE: 10 Ω min. TERMINAL SEAL: Epoxy. Refer to Soldering and Cleaning in Technical DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level. Data chapter. OPERATING TEMPERATURE: –30ºC to 85ºC NOTE: Any models supplied with Q, B, G, P, S or R contact material are RoHS compliant. SOLDERABILITY: Per MIL-STD-202F method 208D, or NOTE: Specifications and materials listed above are for switches with standard options. EIA RS-186E method 9 (1 hour steam aging). For information on specific and custom switches, consult Customer Service Center. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages I–9 and I–10. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function TS01 SPDT On-None-On TS02 SPST Off-None-On TS03 SPDT On-Off-On Terminations A Right angle, PC thru-hole (TS01 & TS03 models only) C PC Thru-hole W Wire wrap Contact Material B Gold Q Silver Seal E Epoxy G Gold over silver F Epoxy seal and splashproof RTV latex rubber seal P Gold, matte-tin S Silver, matte-tin R Gold over silver, matte-tin Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ck-components.com I–8 Slide Slide TS Series Tiny Slide Switches SWITCH FUNCTION SWITCH FUNCTION CONNECTED TERMINALS POS. 1 POS. 2 POS. 3 POS. 1 POS. 2 POS. 3 NO. C&K marking on opposite side C&K marking on opposite side POLES MODEL NO. SCHEMATIC TS01 ON NONE ON 1-2 OPEN 2-3 SP TS03 ON OFF ON SPDT TS02 OFF NONE ON OPEN N/A 3-1 SPST I SPDT TS02 models: Omit center terminal Terminal Nos. For Reference Only Part number shown: TS01CBE All models with all options when ordered with G, Q, R or S contact material. TS02 model not available with A terminations. TERMINATIONS C PC THRU-HOLE W WIRE WRAP PC MOUNTING TS02 models: Omit center hole SPDT and SPST SPDT and SPST A RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TS01ABE Horizontal Actuation SPDT Actuator shown in pos. 1 Not available with TS02 model. Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com I–9 TS Series Tiny Slide Switches CONTACT MATERIAL RATINGS OPTION TERMINAL CONTACT CODE MATERIAL PLATING B 3 GOLD 1 GOLD LOW LEVEL/DRY 0.4 VA MAX. @ 20 V AC OR DC MAX. 6 MATTE-TIN CIRCUIT P Q 5 SILVER TS01 MODELS: 3 AMPS @ 120 V AC OR 28 V DC. 4,5 SILVER POWER TS02, TS03 MODELS: 1 AMP @ 120 V AC OR 28 V DC. 6 MATTE-TIN S TS01 MODELS: 0.4 VA MAX @20 V AC OR DC MAX. OR G 3 GOLD OVER GOLD LOW LEVEL/DRY 3 AMPS @ 120 V AC OR 28 V DC. 2,3 TS02, TS03 MODELS: 0.4 VA MAX @ 20 V AC OR DC MAX. OR SILVER 6 CIRCUIT OR POWER I MATTE-TIN R 1 AMP @ 120 V AC OR 28 V DC. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. All models with all options when ordered with G, S or R contact material. 1 CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. B contact material standard with A and W terminations. 2 END CONTACTS: Coin silver, with gold plate over nickel plate. 3 Q contact material standard with C terminations. CENTER CONTACTS & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. 4 END CONTACTS: Coin silver, silver plated. NOTE: Any models supplied with Q, B, G, P, S or R contact material are RoHS compliant. 5 CENTER CONTACT & ALL TERMINALS: Copper alloy, silver plated. 6 TERMINALS: Copper alloy, with matte-tin over nickel plate SEAL E EPOXY SEAL F EPOXY SEAL AND SPLASHPROOF RTV LATEX RUBBER SEAL NOTE: RTV latex rubber seal peels off easily after installation. Epoxy terminal seal standard. Not available with A termination. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ck-components.com I–10 Slide