CORNELL DUBILIER UPP12W30K

ElectroFilm ElectroFilm Technology - A Film Alternative for Electrolytic Capacitors Metallized Screw Terminal, Snap-In and Polyester & Polypropylene Custom Case Configurations ElectroFilm Technology is a material system used by CDE to fabricate custom capacitors for stable high capacitance, high voltage and/or high current and low ESR applications. ElectroFilm can be made with metallized polypropylene or metallized polyes- ter at very high capacitance values and could be used to replace electrolytic capacitors where increased reliability is desired. ElectroFilm is self-healing, non- polar, and typically has 10 times the ripple current capability, 20 times greater life expectancy and 500 times lower ESR than comparable electrolytic ca- pacitors. A lower in-place cost is achieved by using ElectroFilm Capacitors, because 65% fewer capaci- tors are generally needed when compared to alumi- num electrolytic capacitors for the same application. Features Voltage Range: 300 Vdc to 1200 Vdc Capacitance Range: 7.5 µF to 600 µF Operating Temperature Range: -55° C to +85° C Ripple Current Capability: 25 °C 13.8 Arms to 39.2 Arms 50 °C 11.1 Arms to 31.5 Arms 75 °C 6.8 Arms to 19.2 Arms Type Designation UNL - Snap-In Capacitor Metallized Polypropylene UPP - Screw Terminal Metallized Polypropylene UPE - Screw Terminal Metallized Polyester Cornell Dubilier Electronics 1605 East Rodney French Blvd. New Bedford, MA 02744 Phone: (508)996-8564 Fax: (508)996-3830 www.cde.com CDE ElectroFilm Capacitors - Alternative to Aluminum Electrolytics Catalog Cap D H E.S.R. mΩ 25 °C 50 °C 75 °C dVdt ESL S.R.F. I Vdc Diel. S Joules P mm Arms Arms Arms V/µs (nH) Number µF In. mm In. @ 1 kHz kHz UNL12W7P5K 7.5 1200 MPP 1.42 36.07 2.12 53.85 0.500 14.0 13.8 11.1 6.8 5.40 56 420 35 309 UNL6W30K 30 600 MPP 1.42 36.07 2.12 53.85 0.500 8.0 18.1 14.6 8.9 5.40 28 840 35 155 UNL5W35K 35 500 MPP 1.42 36.07 2.12 53.85 0.500 8.0 18.6 15.0 9.1 4.38 25 875 35 143 UPE10W120K 120 1000 MPE 3.00 76.2 5.13 130.2 1.250 18.0 25.6 20.6 12.5 60.0 19 2280 81 71 UPE6W240K 240 600 MPE 3.00 76.2 4.13 104.8 1.250 8.5 32.7 26.2 16.0 43.2 14 3360 61 42 UPE3W600K 600 300 MPE 3.00 76.2 3.13 79.38 1.250 5.0 39.2 31.5 19.2 27.0 11 6600 47 30 UPP12W30K 30 1200 MPP 2.50 63.5 3.13 79.38 1.125 6.2 30.3 24.3 14.8 21.6 47 1410 42 143 UPP12W60K 60 1200 MPP 2.50 63.5 4.13 104.8 1.125 7.5 31.1 24.9 15.2 43.2 27 1620 82 70 UPP6W120K 120 600 MPP 2.50 63.5 3.13 79.38 1.125 5.0 36.7 29.4 18.0 21.6 23 2760 43 70 Pin: 0.050 " Tapered to 0.035 " Pin Base to Below Case Stand-off Leads to be tin dipped in 60/40 solder 0.200 " UPE & UPP 0.300 " ± 0.005 " 0.031 " + 0.015 " ± 0.003 " 0.100 " - 0.030 " D ± 0.031" 0.315 " ± 0.005 " H ± 0.031 " S ± 0.015 " 2 x 1/4-28 UNF Threads D " 2 x∅ 0.687 0.38 " Deep Min. Max. UNL 0.13 " ± 0.063 " 0.312 " H ± 0.062 " S ± 0.031 " Cornell Dubilier Electronics 1605 East Rodney French Blvd. New Bedford, MA 02744 Phone: (508)996-8564 Fax: (508)996-3830 www.cde.com Rev. 5-20-2004