Module 17plus Description Module 17plus is a power distribution system for use with ● E-T-A Circuit Breakers type 2210-S..., 3600-..., 3900-... ● E-T-A Electronic Circuit Breaker ESS20, ESX10 ● Solid State Remote Power Conroller E-1048-7... Each module accommodates two single pole plug-in circuit breakers with an individual housing width of only 12.5 mm and fits onto all industry standard mounting rails. The two-way modules can be mounted side-by-side to provide as many ways as required with a terminal block fitted at each end. A distribution busbar can be fitted on the supply side of the modules, but each pole of multipole circuit breakers must be individually connected. 17plus Electrical connections are by means of screwless spring loaded terminals. Suitable electro-mechanical circuit breakers have integral make and Technical data break auxiliary contacts. Depending on the application these may be used for either single or group signalisation. For group signalisation, Connection Spring-loaded terminals for rigid wires the make contacts (which open in the event of a fault) are connected or flexible cables with unisolated wire in series to the terminal blocks of the modules. The module is designed end ferrules or without wire end ferrules. to accommodate a probe for series connection continuity tests. When Please use appropriate screw driver size multipole circuit breakers are fitted auxiliary contacts are required for (SD) for removing the spring loaded each pole. terminals. Single signalisation is achieved through use of the break contacts (which close in the event of failure) connected in parallel by means of cable cross section of screw driver stripped terminals on each module. connecting cable length Both types of signalisation (single and group signalisation) are available 2 Line feed (1) 1.5-10 mm 3 (1.0 x 5.5) 12 mm at the same time if the circuit breakers used provide auxiliary contacts 2 Load output (2) 0.25-4 mm 1 (0.6 x 3.5) 12 mm (please note when ordering). 2 The signalling circuitry between modules is automatically connected Signalisation 0.25-2.5 mm 1 (0,6 x 3.5) 10 mm when the modules are mounted side-by-side (linked together).201107terminals (11, 13, 14) 2 Signalisation 0.25-1.5 mm 0 (0.4 x 2.5) 9 mm terminal (12) Ordering information diameter of test socket ≤ 2 mm ø Voltage rating 17PLUS-Q02-00 Module 17plus, centre piece, two-way (without circuit breaker): AC 250 V; 3 AC 433 V; DC 65 V 17PLUS-QA0-LR one each left- and right-side terminal block Current rating (without circuit breaker) for supply feed from the side by means of Line feed (1) 50 A screw terminal Load output (2) 25 A Technical data of: please see: Signalisation Feed (11) Circuit Breaker 2210-S, 3600, 3900 product group 2 (ground with electronic components) 10 A Electronic Circuit Breaker ESS20, ESX10 product group 5 Single output (12) 1 A Solid State Remote Power Controller E-1048-7.. product group 6 Group signal (13-14) 1 A Caution: When several devices are mounted together, each should carry only max. 80 % ( I ≤ 16 A) or max. 65 % (I > 16 A) of its rating. N N Internal resistances (without circuit breaker) Approvals Line/load (1-2) ≤ 5 mΩ 7 Signalisation (11-12) ≤ 9 mΩ (+ 2 mΩ per additional module) Authority Voltage ratings Current ratings Group signal (13-14) ≤ 8 mΩ (+ 5 mΩ per additional module) UL 60950 AC 250 V; DC 80 V 50 A Vibration 5 g (57-500 Hz) ± 0.38 mm (10-57 Hz), to IEC 60068-2-6, test Fc, 10 frequency cycles/axis Shock 25 g (11 ms) to IEC 60068-2-27, test Ea 11 ms half sine Corrosion 96 hours at 5 % salt mist, to IEC 60068-2-11, test Ka Humidity 240 hours at 95 % RH to IEC 60068-2-78, test Cab Dielectric strength between main circuits (without busbar): 1,500 V main circuit to auxiliary circuit: 1,500 V between auxiliary circuits: 1,500 V Mass: Module 17plus (centre piece) approx. 85 g terminal blocks (pair) approx. 30 g Issue B(300710) www.e-t-a.com 7 - 9 Modul 17 plus GERMANY Module 17plus Dimensions Installation example slot for fitting labels from Phoenix, Weidmüller, Weidmüller 6 4 5 17 plus 3 3 63 6 25 25 G-profile EN 50035-G32 .984 2.48 .236 .984 2 115 37 4.53 1.46 symmetrical rail 1 EN 50022-35x7.5 slot for busbar right-side terminal block Installation: test socket 1 Clip modules onto DIN rails. 2 Push modules together (side-by-side). left-side terminal block 3 Snap on right-side and left-side terminal blocks. module 4 Cut busbar to required length and fit on supply side of the modules. 5 Connect line feed with spring-loaded terminals. 6 Plug in circuit breakers. 1 Line 1 Line Connection diagram SD 3 1 Line 1 Line SD 1 Example for circuit breaker types 2210, 3600, 3900 11 11 11 11 module 1 module 2 13 14 SD 1 busbar Supply LINE 1 LINE 1 LINE 1 LINE 1 2 2 12 12 13 14 11 11 7 2 2 SD 0 12 12 Connection and disconnection of cables with screw driver 13 14 LOAD 2 12 LOAD 2 12 LOAD 2 12 LOAD 2 12 Module 17plus for electronic overcurrent protection jumper circuit breaker left-side terminal block right-side terminal block test socket For technical data, dimensions, mounting examples, schematic diagrams and connection diagrams of 13, 14 terminals for group signalisation 11 feed for single signalisation 12 terminal for single signalisation ● ESS20-0... please see product group 5 ● ESS20-1... please see product group 5 For connection diagram for electronic circuit breakers ● ESX10 please see product group 5 and components please see relevant data sheets of ● E-1048-7... please see product group 6 types ESS20, ESS21, E-1048-7.. mm This is a metric design and millimeter dimensions take precedence ( ) inch 7 - 10 www.e-t-a.com Issue B(300710) LOAD LOAD LOAD LOAD 2 12 2 12 12 2 12 2 1 LINE 1 LINE 1 LINE 1 LINE 11 11 13 14 47 1.85 42.5 68 10.5 1.67 2.64 .413 1 Line 1 Line 11 11 14 14 2 2 12 12 57 2.24 64.5 2.54 Module 17plus Accessories Retaining clip Y 308 792 01 Busbar 32 A recommended for tight fit of types X 222 005 01 blue insulation, 500 mm/19.68 in. ESX10 / E-1048-S6xx / SB-S11-P1-xx X 222 005 02 red insulation, 500 mm/19.68 in. and terminal blocks type 17 and 17plus X 222 005 03 grey insulation, 500 mm/19.68 in. ”up to 32 A continuous load“ 64 2.52 Busbar 50 A Y 307 016 01 non-insulated, 500 mm/19.68 in. ”up to 50 A continuous load; plugged in completely, protected against brush contact“ Retaining clip Y 307 754 01 recommended for tight fit of types ESS20 / ESX10 18.5 .728 Busbar 50 A Y 307 016 11 non-insulated, 500 mm/19.68 in. ”up to 50 A continuous load“ End bracket Screw terminal for busbar X 222 004 01 X 211 156 01 non insulated 2 (up to 35 mm ) Width 10 mm 2 .079 Jumper SB-S11-P1-01-1-1A top view Retaining clip for circuit breaker 3600/3900 recommended for fitting the devices Y 300 581 11 Germany 45 Signalbrücke 1.77 Signal loop SB-S11-P1-01-1-1A www.e-t-a.com xxxx 60 mounting dimensions 2.36 7 AC 240 V / DC 65 V, 1 A 30 1.18 12.3 Retaining clip for circuit breaker 2210 .484 recommended for fitting single pole devices Y 302 974 21 45 1.77 blade terminals DIN 46244-A 6.3-0.8 terminals 13+14 bridged Labels 60 marking area 6 x 10 mm mounting dimensions 2.36 (ordering unit 10 pcs = 1 strip) Y 307 942 61 24 .945 All dimensions without tolerances are for reference only. In the interest of improved design, performance and cost effectiveness the right to make changes in these specifications mm without notice is reserved.Product markings may not be exactly as the ordering codes. This is a metric design and millimeter dimensions take precedence ( ) inch Errors and omissions excepted. Issue B(300710) www.e-t-a.com 7 - 11 ø1 ø1 .039 .039 5.5 7 .276 .217 61.5 44.4 2.42 1.74 8 10.3 70 .315 .406 2.76 1 13 14 5 4.5 .197 .177 2 60 2.36 Signalbrücke Signal loop Module 17plus 7 7 - 12 www.e-t-a.com Issue B(300710)