Thermal-Magnetic Circuit Breaker 2210-S2... Description One, two and three pole thermal-magnetic circuit breakers with tripfree mechanism and toggle actuation (S-type TM CBE to EN 60934/IEC 934). Designed for panel or plug-in mounting. Available with auxiliary contacts (1 x N/O, 1 x N/C) for status signalling. Two and three pole models are internally linked to ensure that both/all poles trip in the event of an overload on one pole, even if the actuator is held in the ON position. A choice of characteristic curves further extends the range of applications possibilities for these CBEs. Special auxiliary contact versions for industrial atmosphere and low voltages (e. g. 5 V) available on request. Approved to CBE standard EN 60934 (IEC 60934). Suitable for use in distribution rails – see section Power Distribution Systems. 1 2210-S2.. Typical applications Process control equipment, robotics, machine tool control, communications Technical data systems, instrumentation, rail vehicles. Special versions, e.g. for aggressive environmental conditions and low voltages (e. g. 5 V) on request. For further details please see chapter: Technical Information Voltage rating AC 250 V*; 3 AC 433 V (50-60Hz); DC 65 V Standard current ratings and typical internal resistance values (*UL: AC 277/480 V; DC 65 V) Current rating range 0.1...25 A for curves M1, T1 0.1...16 A for curves F1, F2 Current Internal resistance (Ω) 1...16 A for curves M3 rating (A) Auxiliary circuit 1 A, AC 240 V/DC 65 V, resistive F1 F2 M1 T1 M3 (min. 10 V / 10 mA) fast acting fast acting standard delayed standard Typical life 10,000 operations at 1 x I , inductive N delay low delay for DC only for AC+DC resistance Ambient temperature -30...+60 °C (-22...+140 °F) T 60 for AC+DC only for AC Insulation co-ordination rated impulse pollution 0.1 162 162 92 81 - (IEC 60664 and 60664A) withstand voltage degree 2.5 kV 2 0.2 39.3 39.3 26.1 24.2 - reinforced insulation in operating area 0.3 17.5 17.5 11.6 10.4 - Dielectric strength 0.4 9.2 9.2 6.6 6.0 - (IEC 60664 and 60664A) test voltage 0.5 6.8 6.8 4.1 3.9 - operating area AC 3,000 V 0.6 4.2 4.2 3 2.7 - main/aux. circuit AC 1,500 V aux. circuit 11-12/23-24 AC 1,000 V 0.8 2.8 2.8 1.65 1.53 - pole/pole AC 1,500 V 1 1.6 1.6 1.10 0.98 0.5 Insulation resistance > 100 MΩ (DC 500 V) 1.5 0.78 0.78 0.47 0.42 0.22 Interrupting capacity I 0.1...5 A 400 A cn 2 0.42 0.42 0.28 0.24 0.136 6...25 A 800 A 2.5 0.26 0.26 0.183 0.17 0.083 curves F1, F2, M1, T1: 0.1...16 A 2,500A (at DC 32 V) curve M3: 1...2 A AC 200 A DC 400 A 3 0.18 0.18 0.124 0.12 0.057 4 0.12 0.12 0.077 0.073 0.041 Interrupting capacity (UL 1077) 5 0.092 0.092 0.063 0.055 0.032 I 0.1...16 A 20...25 A N 6 0.054 0.054 0.045 0.039 0.021 AC 277 V 1-pole 5,000 A 2,000 A 8 0.025 0.025 ≤ 0.02 ≤ 0.02 ≤ 0.02 AC 277/480 V 2-/3-pole 5,000 A 2,000 A 10 0.022 0.02 ≤ 0.02 ≤ 0.02 ≤ 0.02 DC 65 V 2,000 A 2,000 A 12 ≤ 0.02 ≤ 0.02 ≤ 0.02 ≤ 0.02 ≤ 0.02 Degree of protection operating area IP30 16 ≤ 0.02 ≤ 0.02 ≤ 0.02 ≤ 0.02 ≤ 0.02 (IEC 60529/DIN 40050) terminal area IP00 20 - - ≤ 0.02 ≤ 0.02 - Vibration curves F1, F2: 25 - - ≤ 0.02 ≤ 0.02 - 3 g (57-500 Hz), ± 0.23 mm (10-57 Hz) curves M1, M3, T1: 5 g (57-500 Hz), ± 0.38 mm (10-57 Hz) Preferred types to IEC 60068-2-6, test Fc 10 frequency cycles/axis Preferred types Standard current ratings (A) Shock curves F1, F2: 25 g (11 ms), directions 1, 2, 3, 4, 5 1-pole: 1 2 4 6 8 10 16 10 g (11 ms), direction 6 curves M1, M3, T1: 2210-S211-P1F1-H111- x x x x x 25 g (11 ms), directions 1, 2, 3, 4, 5 x x x x x x x 20 g (11 ms), direction 6 2210-S211-P1M1-H111- to IEC 60068-2-27, test Ea x x x x x x x 2210-S211-P1M1-Z111- Corrosion 96 hours in 5 % salt mist to IEC 60068-2-11, test Ka 2-pole: Humidity 240 hours at 95 % RH x x x x x x x 2210-S221-P1M1-H111- to IEC 60068-2-78, test Cab Mass approx. 50 g per pole x x x x x x x 2210-S221-P1M1-H211- 1812 www.e-t-a.de 1 2 A 2 A 2 A M1 M1 M1 25° Thermal-Magnetic Circuit Breaker 2210-S2... Ordering information Dimensions Type No. 30.5 2210 single or multipole thermal-magnetic circuit breaker Z 1.20 Mounting 18 S socket or panel mounting .709 Actuator design ON OFF 2 toggle Number of poles 1 1-pole protected 2 2-pole protected 19 37.5 3 3-pole protected .748 1.48 3.5 43 Panel mounting .138 1.69 25 1 with M3 thread .984 Terminal design (main contacts) 1 P1 blade terminals 6.3-0.8 (QC .250) 12.5 .492 Characteristic curve 11.5 F1 fast acting: therm.1.01-1.4xI ;magn.2-4xI DC (DC only) N N 12 11 3 24 12 2 .453 F2 fast acting: therm.1.01-1.4xI ; N magn.3.5-6.5xI AC/ 4.5-8.5xI DC N N M1 standard delay: therm. 1.01-1.4xI ; N 6.8 polarizing tooth 12.5 12.5 magn. 6-12xI AC;7.8-15.6xI DC N N .268 .492 .492 T1 delayed: therm. 1.01-1.4xI ; magn. 10-20xI AC N N 6x6.8 = 40.8 blade terminals M3 standard delay, low resistance: therm.1.4-1.8xI ; 6x.268 = 1.61 N DIN 46244-A6.3-0.8 (QC .250) magn. 6-12xI AC; 7.8-15.6xI DC N N 50 Intermediate position mounting thread M3 1.97 max. screw length 5.8 mm (.228 in.) H without intermediate position (standard) 32 tightening torque max. 0.5 Nm Z with intermediate position 1.26 Auxiliary contacts unit III 1 with auxiliary contacts in all poles 2 with auxiliary contacts in pole 1 unit II (only multipole devices) not suitable for Module 17plus unit I Auxiliary contact function (see diagram) multipole devices 1 one each N/C and N/O (standard) 16 4 one N/C contact, closed in the .630 intermediate and ON position (-Z only) Auxiliary contact - terminal design 1 same as main terminals Cut-out dimensions Current ratings 0.1...25 A 2210 - S 2 1 1 - P1 F1 - H 1 1 1 - 10 A ordering example 32 3-pole 1.26 2-pole 16 1-pole Approvals .630 ø11.5 .453 Authority Standard Rated voltage Current ratings VDE IEC/EN 3 AC 433 V 0.1 A…32 A 90° 60934 AC 250 V 0.1 A…32 A recess with panel thickness DC 65 V 0.1 A…32 A s > 1.5 mm (.059 in.) UL UL 1077 AC 277/480 V 0.1 A…32 A ø11.5 AC 277 V 0.1 A…32 A .453 DC 65 V 0.1 A…32 A CSA C22.2 No AC 277/480 V 0.1 A…32 A AC 277 V 0.1 A…32 A 235 Installation drawing DC 65 V 0.1 A…32 A CQC GB 17701 AC 250/433 V 0.1 A…25 A operating area AC 250 V 0.1 A…25 A (reinforced insulation) 0.1 A…25 A DC 65 V GL IEC/EN 3 AC 433 V 0.1 A…32 A AC 250 V 0.1 A…32 A 60934 DC 65 V 0.1 A…32 A 12 11 3 24 12 2 mounting area (standard insulation) mm This is a metric design and millimeter dimensions take precedence ( ) inch 1812 2 www.e-t-a.de 25° ø4 .157 36.6 24 0 0 0 5.5 10 1 .217 .394 .039 5 68 10.5 ø11 12.5 12.5 2.68 .413 .433 20 1.5 12 .472 s 1.44 .945 .197 .492 .492 .787 .059 Thermal-Magnetic Circuit Breaker 2210-S2... Thermal-Magnetic Circuit Breaker 2210-S2... Internal connection diagrams Typical time/current characteristics -F1 0.1…16 A DC only 10000 with auxiliary contact function 1 (one each N/O and N/C) (...-H111-...) without intermediate position (...-Z111-...) with intermediate position 1000 line line line (Z) (Z) (Z) 100 0I 111 23 0 I 111 23 0I 11123 10 12 24 12 24 12 24 1 I > I > I > 1 0.1 2 2 2 OFF position Intermediate position ON position 0.01 with auxiliary contact function 4 (1 N/O, leading) 0.001 line line line 12 46 810 20 40 6080100 (Z) (Z) (Z) 0I 123 0I 123 0 I 123 … times rated current 1) -F2 0.1…7.5 A AC/ DC 10000 24 24 24 1000 I > I > > I 100 2 2 2 OFF position Intermediate position ON position 10 1 Toggle positions 0.1 OFF position intermediate positionON position 0.01 0.001 40 6080100 12 46 81020 … times rated current 1) -F2 8…16 A AC/ DC 10000 Shock directions 1000 100 3 56 10 4 1 1 2 0.1 0.01 current rating 0.001 12 46 81020 40 6080100 … times rated current +60 °C +23 °C -30 °C +140 °F +73.4 °F -22 °F 1) Magnetic tripping currents are increased by 30 % on DC supplies. Multipole devices: all poles symmetrically loaded. With single pole overload, thermal tripping will be at max. 1.7 x I with curves F1, F2 and M1 at max. N 2.2 x I with curve M3. N The time/current characteristic curve depends on the ambient temperature prevailing. In order to eliminate nuisance tripping, please multiply the circuit breaker current ratings by the derating factor shown below. See also section Technical information. -22 -4 +14 +32 +73.4 +86 +104 +122 +140 Ambient °F -30 -20 -10 0 +23 +30 +40 +50 +60 temp. °C 0.76 0.79 0.83 0.88 1 1.04 1.11 1.19 1.29 Derating factor 1812 www.e-t-a.de 3 Trip time in seconds Trip time in seconds Trip time in seconds Thermal-Magnetic Circuit Breaker 2210-S2... Typical time/current characteristics 1) 1) -M1 8…25 A AC/DC -T1 0.1…6 A AC only -M1 0.1…6 A AC/DC 10000 10000 10000 1000 1000 1000 100 100 100 10 10 10 1 1 1 1 0.1 0.1 0.1 0.01 0.01 0.01 0.001 0.001 0.001 12 46 810 20 406080100 12 46 810 20 406080100 12 46 810 20 406080100 … times rated current … times rated current … times rated current 1) 1) -T1 8…25 A AC only -M3 1…5 A AC/DC -M3 6…16 A AC/DC 10000 10000 10000 1000 1000 1000 100 100 100 10 10 10 1 1 1 0.1 0.1 0.1 0.01 0.01 0.01 0.001 0.001 0.001 12 46 810 20 406080100 12 46 810 20 406080100 12 46 810 20 406080100 … times rated current … times rated current … times rated current The time/current characteristic curve depends on the ambient temperature Multi pole devices: all poles symmetrically loaded. With single pole overload, prevailing. In order to eliminate nuisance tripping, please multiply the circuit thermal tripping will be at max. 1.7 x I with curves F1, F2 and M1 at max. 2.2 x N breaker current ratings by the derating factor shown below. See also section I with curve M3. N Technical information. 1) Magnetic tripping currents are increased by 30% on DC supplies -22 -4 +14 +32 +73.4 +86 +104 +122 +140 Ambient °F (curves F2, M1, M3). -30 -20 -10 0 +23 +30 +40 +50 +60 temp. °C 0.76 0.79 0.83 0.88 1 1.04 1.11 1.19 1.29 Derating factor 1812 4 www.e-t-a.de Trip time in seconds Trip time in seconds Trip time in seconds Trip time in seconds Trip time in seconds Trip time in seconds Thermal-Magnetic Circuit Breaker 2210-S2... Thermal-Magnetic Circuit Breaker 2210-S2... Accessories Single mounting sockets (with adapter) Module 17plus (up to 16 A max. load) For technical data see section Power Distribution Systems 17-P10-Si 17-P10-Si-20025 17-P70-Si 17-P70-Si-20025 (retaining clip Y 302 974 21 available on request) slot for fitting labels from Phoenix, Weidmüller, Wieland polarized blade terminal blade terminal DIN 46244 part 2 DIN 46244-A6.3-0.8 (QC .250) C profile (2xA2.8-0.8) (QC 2x.110) -P10 -P70 slot for fitting labels from 6.3 2.8 Phoenix, Weidmüller 1 .248 .110 retaining clip depth 17 plus 10 mm 10 (.394 in.) .394 2(k) 2(k) 1 1 12 12 11 11 63 6 25 24 24 G-profile 25 23 23 2(i) 2(i) EN 50035-G32 .984 2.48 .236 .984 115 37 80 12.5 4.53 1.46 symmetrical rail 3.15 .492 EN 50022-35x7.5 symmetrical rail EN 50022-35x7.5 slot for busbar G-profile polarization recess adapter X20040901 EN 50035-G32 right-side terminal block Bus bar 50 A (6-way) for type 17-P10-Si socket X 221 760 01 left-side terminal block 71 ± 1.5 module blade terminal 2.79 ± .060 DIN 46244 A6.3-0.8 25 (QC .250), max. 25 A .984 2-way 6-way mounting socket mounting socket 23-P10-Si 63-P10-Si (up to 16 A max. load) (retaining clip Y 302 974 01 available on request) 12.5 max. 30 75 .492 2.95 max. 1.18 insulation to busbar Outer dimensions of female 25 4.4 12.5 6 DIN 4102-B2 max. 50 A connectors to .492 .984 .173 .236 translucent 6.3-1 DIN 46247 Ms-gal Sn 50 2 polarized 12.5 max. 16 A recess 1.97 .079 .492 Bus bar (10-way) (supplied as a complete package) for type 17 socket (for max. 100 A continuous load), more positions available on request X 211 157 01 with terminal 12.5 6.25 10 4.4 X 211 157 02 without terminal .173 .492 .394 .246 7.4 21 7.4 Phoenix terminal AKG 35 cylinder head screw washer retaining 2 .827 .291 max.cross section 35 mm (AWG 2) M4x4 ISO1207 A 4.3 DIN 125 .291 clip 22.2 nickel plated nickel plated .874 polarized blade terminals DIN 46244-A6.3-0.8 (QC .250) Bus bar 50 A, 6-way, for type 63-P10-Si socket female X 221 760 11 connector M4 Cu rail, tin-plated 71 ± 1.5 blade terminal 2.79 ± .060 DIN 46244 A6.3-0.8 25 (QC .250), max. 25 A .984 7 12.8 .276 pressure-relief joint .504 (1.1 mm (.043 in.) 154.8 thick constriction) 6.09 12.5 Insulating sleeving for bus bar (10-way) .492 Y 303 824 01 busbar Outer dimensions of female insulation to max. 50 A connectors to DIN 4102-B2 6.3-1 DIN 46247 Ms-gal Sn translucent 9 max. 16 A .354 5.4 125 .213 4.92 mm This is a metric design and millimeter dimensions take precedence ( ) inch 1812 www.e-t-a.de 5 57.4 47 50 1.85 68 42.5 10.5 1.67 2.64 .413 1 Line 1 Line 64 57.4 11 11 50 14 14 2 2 12 12 64 57 8 2.24 .315 33.2 1.31 6.8 6 x 6.8 = 40.8 3.5 6 x .268 = 1.61 25.8 6.5 8.5 17 .669 33.3 1.4 5 10 41.3 2 8 .079 .315 10 33.2 .394 1.31 10 45.8 2.26 1.97 2.52 2.26 1.97 2.52 .268 .138 .256 1.02 .335 1.31 .055 .197 .394 1.63 .394 1.80 R15 .591 Thermal-Magnetic Circuit Breaker 2210-S2... Accessories Connector bus links -P10 Splash cover (transparent) 2 X 210 588 01/ 1.5 mm , (AWG 16), brown (up to 13 A max. load)2 with fixing plate and screws (IP54) 2 X 210 588 02/ 2.5 mm , (AWG 14), black (up to 20 A max. load) for type 2210-S211-… (1-pole) 2 X 210 588 03/ 2.5 mm , (AWG 14), red (up to 20 A max. load) X 211 117 02 2 X 210 588 04/ 2.5 mm , (AWG 14), blue (up to 20 A max. load) 31 100 quick-connect tabs 6.3 (.250) 1.22 DIN 46247 tinned brass, insulated ø16.8 mounting holes .661 fixing plate 1 39 1.54 Toggle guard for 1-pole units, black 32 X 221 617 01 32 1.26 1.26 mounting dimensions: 24 M3 - hole dia. 3.5 mm/.138 in. .945 Splash cover (transparent) with fixing plate and screws (IP54) for type 2210-S221-… (2-pole) and 20 type 2210-S231-… (3-pole) .787 X 211 118 01 38 1.50 38 32 1.50 1.26 22 24.5 .866 .965 fixing plate mounting hole For front panel mounting. +0.3 25 53 +.012 2.09 .984 ±0.1 32 ±.004 1.26 mm This is a metric design and millimeter dimensions take precedence ( ) inch All dimensions without tolerances are for reference only. In the interest of improved design, performance and cost effectiveness the right to make changes in these specifications without notice is reserved.Product markings may not be exactly as the ordering codes. Errors and omissions excepted. 1812 6 www.e-t-a.de R12 .472 12 ~70 .472 ~2.76 3.6 .142 .098 .138 .039 .374 .217 1.2 21 1.2 21 .047 .827 .827 43 .047 1.69 max. 2 19 max .079 ±0.1 .748 2pole 12.6 max. 4 ±.004 max .157 .496 ±0.1 3pole 25.2 ±.004 3pole .992 +0,2 40 ø17 1.57 +.008 .669 2.5 ø3.5 1 5.5 9.5