E-T-A 4130-G411-K4M1-25A

High Performance Thermal Circuit Breaker 4130-... Description Single pole high performance thermal circuit breaker, with push-to- reset tease free, trip-free snap action mechanism (R-type TO CBE to EN 60934). Designed for threadneck panel mounting and for applications with a high fault current switching requirement. Approved to CBE standard EN 60934 (IEC 60934). 1 Typical applications Motors, transformers, solenoids, battery chargers, power supplies, appliances, machinery, extra low voltage systems. 4130-... Ordering information Technical data Type No. For further details please see chapter: Technical Information 4130 single pole thermal circuit breaker Voltage rating AC 240 V; DC 50 V Mounting Current rating range 20...70 A G threadneck panel mounting Threadneck design Typical life 2 M12x1, knurled nut (bulk shipped) AC 240 V: 20...70 A 100 operations at 2 x I , inductive N 4 M12x1, hex nut and knurled nut (bulk shipped) 500 operations at 2 x I , resistive N Number of poles DC 50 V: 20...80 A 500 operations at 2 x I , inductive N 1 single pole, thermally protected Ambient temperature -30...+60 °C (-22...+140 °F) Actuator configuration Insulation co-ordination rated impulse pollution 1 black push button (IEC 60664) withstand voltage degree Terminal design 2.5 kV 2 K4 terminal M6x8 (reinforced insulation in the mounting area) screw and washer bulk shipped Characteristic curve Dielectric strength M1 medium delay operating area test voltage Current ratings AC 3,000 V 20... 70 A Insulation resistance > 100 MΩ (DC 500 V) Interrupting capacity I 800 A cn 4130 - G 2 1 1 - K4 M1 - 20 A ordering example Interrupting capacity (UL 1077) I U N N 20...70 A AC 240 V 1,000 A 20...60 A AC 120 V 3,500 A 70 A AC 120 V 2,000 A 20...50 A DC 50 V 3,500 A Standard current ratings and typical internal resistance values 60...70 A DC 50 V 2,000 A Degree of protection operating area IP40 Current Internal Current Internal (IEC 60529/DIN 40050) terminal area IP00 rating (A) resistance (Ω) rating (A) resistance (Ω) Vibration 8 g (57-500 Hz) ±0.61 mm (10-57 Hz) 20 < 0.02 40 < 0.01 to IEC 60068-2-6, test Fc 25 < 0.02 50 < 0.01 10 frequency cycles/axis 30 < 0.02 60 < 0.01 Shock 25 g (11 ms) 35 < 0.02 70 < 0.01 to IEC 60068-27, test Ea Corrosion 96 hours at 5 % salt mist, to IEC 60068-2-11, test Ka Humidity 240 hours at 95 % RH to IEC 60068-2-3, test Ca Mass approx. 55 g Approvals Authority Voltage ratings Current ratings VDE (EN 60934) AC 240 V; DC 50 V 20...70 A UL AC 240 V; AC 120 V; DC 50 V 20...80 A 06/07 www.e-t-a.com 1 - 89 High Performance Thermal Circuit Breaker 4130-... Dimensions Typical time/current characteristics 10000 60 °C tightening torque max. 1.5 Nm M12x1 ø6.6 23 °C black .260 -30 °C 1000 1 100 10 I 2 1 13.5 12 .531 .472 screw M6x8 with washer max. 3.5 22.3 17 tightening torque max. 2.5 Nm max .138 .878 .669 0,1 0,812 3546810 20 40 D-shaped threadneck mounting hole ... times rated current The time/current characteristic curve depends on the ambient temperature prevailing. In order to eliminate nuisance tripping, please multiply the circuit breaker current ratings by the derating factor shown below. See also 32 11.5 -0.1 section 9 – Technical information. 1.26 .453 -.004 Ambient temperature °F -22 -4 +14 +32 +73.4 +104 +122 +140 °C -30 -20 -10 0 +23 +40 +50 +60 Derating factor 0.68 0.76 0.84 0.92 1 1.08 1.16 1.24 Intstallation drawing Accessories Hex nut with splash cover, black Water splash cover, X 201 296 01 without O ring (IP64) transparent with knurled operating area X 200 801 03 with O ring (IP66) nut and O ring (IP64) Hex nut with splash cover, X 210 663 01 transparent X 200 801 08 with O ring (IP66) M12x1 M12x1 I 2 Separate hardware Knurled nut Hex nut Y 300 116 02 Y 302 065 01 mounting area 30 6 M12x1 M12x1 3.2 1.18 .236 .126 SW14 2.5 ø17 0.5 x 45° .551 .098 .669 .020 x 45° Internal connection diagram line 1 mm This is a metric design and millimeter dimensions take precedence ( ) inch All dimensions without tolerances are for reference only. In the interest of improved design, 2 performance and cost effectiveness the right to make changes in these specifications without notice is reserved.Product markings may not be exactly as the ordering codes. Errors and omissions excepted. 1 - 90 www.e-t-a.com 06/07 ±0.5 23.8 OFF ±.020 .937 ±0.5 50 17.2 ON ±.020 1.97 .677 LINE LINE ±0.2 0.6 18 ±.008 .024 .709 64 10.3 2.52 .406 5 .197 12.2 -0.1 .480 -.004 Trip time in seconds