EATON BUSSMANN TR/MCR-3/4

OBSOLETE - Recommended replacement with MCRW, Data Sheet 4074 - OBSOLETE Subminiature Through Hole MCR Series, Fast Acting, Solid Matrix Description • Axial Leaded • Fast Acting, Solid Matrix Construction • High Temperature Thermoplastic Body, UL 94 VO • Tin-lead plated copper Lead Wires, .025" diameter ELECTRICAL CHARACTERISTICS % of Amp Rating (0-10A) Opening Time 100% 4 hours minimum 250% 5 seconds maximum Agency Information • Terminal Strength: MIL-STD-202, Method 211, Test • UL Recognition Guide & File Numbers: Condition A, will withstand 7 lb. axial pull test. JDYX2 & E19180 • Thermal Shock: MIL-STD-202, Method 107, Test • CSA Certification File & Class Numbers: 053787 C 00 & Condition B, -65°C to 125°C 1422 30 (0 - 1/8A); 053787 C 00 & 1422 01 (1/4A - 8A) • Thermal Cycle: EIA-STD-RS-186-C, Test Condition A, Ordering -55°C to 85°C • Vibration: MIL-STD-202, Method 204, Test Condition C, • Specify product code and packaging code (55 to 2000 HZ, 10G’s peak) Environmental Data • Wave Soldering: Maximum reservoir temperature • Life Test: 2000 hours at 80% rated current, 55°C 260°C, 10 second maximum exposure, .125" from body. • Moisture Resistance: MIL-STD-202, Method 106, 90% mm relative humidity at 65°C. Dimensions ⁄(inches) ±0.005" • Operating Temperature: -55°C to 125°C with proper fuse *All tolerances: ±0.13mm derating 1.13" 1.13" • Resistance to Soldering Heat: MIL-STD-202, Method 28.58mm 28.58mm 210, Test Condition C (260°C) .297" .12" • Salt Spray: MIL-STD-202, Method 101, Test Condition B 7.54mm 3.10mm • Shock: MIL-STD-202, Method 213, Test Condition I, 100G’s for 6 milliseconds .025" • Solderability: MIL-STD-202, Method 208 0.64mm SPECIFICATIONS 2 2 Rated Interrupting Pre-arching Typical Total Clearing Typical Voltage 1 2 2 2 2 Product Voltage Rating I t (A sec) I t (A sec) Drop Volts at Code AC DC AC DC AC DC AC DC 100% Rated -6 -7 -6 -7 MCR-1/16 125V 125V 50A 300A 1.1 x 10 1.0 x 10 1.8 x 10 1.5 x 10 2.33 -6 -7 -6 -7 MCR-1/8 125V 125V 50A 300A 4.3 x 10 7.1 x 10 7.3 x 10 8.7 x 10 1.52 -5 -6 -4 -6 MCR-1/4 125V 125V 50A 300A 8.0 x 10 1.0 x 10 1.2 x 10 1.3 x 10 .76 -5 -6 -4 -6 MCR-3/8 125V 125V 50A 300A 9.7 x 10 6.7 x 10 1.1 x 10 8.3 x 10 .73 -4 -5 -3 -5 MCR-1/2 125V 125V 50A 300A 7.4 x 10 5.4 x 10 6.2 x 10 6.8 x 10 .65 -3 -5 -2 -5 MCR-3/4 125V 125V 50A 300A 1.3 x 10 7.4 x 10 7.5 x 10 9.2 x 10 .55 MCR-1 125V 125V 50A 300A .01 .01 .02 .01 .24 MCR-1 1/2 125V 125V 50A 300A .03 .02 .04 .03 .20 MCR-2 125V 125V 50A 300A .09 .07 .11 .08 .16 MCR-2 1/2 125V 125V 50A 300A .19 .14 .25 .17 .15 MCR-3 125V 125V 50A 300A .35 .28 .45 .32 .15 MCR-3 1/2 125V 125V 50A 300A .56 .37 .83 .43 .14 MCR-4 125V 125V 50A 300A .96 .67 1.37 .77 .13 MCR-5 125V 125V 50A 300A 1.82 1.34 2.53 1.51 .11 MCR-7 60V 90V 50A 300A 1.48 .49 2.02 .58 .10 MCR-10 60V 90V 50A 300A 3.62 1.16 4.41 1.38 .08 1. Interrupting ratings were measured at 100% (1/16 to 5) and 100% (7, 10) power factors on AC, and a time constant less than 1 ms. on DC. 2 2. I t was measured at 50 amps 125 VAC, .95PF, (random closing angle) and 300 amps 125 VDC, TC <1ms. for 1/16 through 5 amps and 50 amps 60 VAC, .95PF, (random closing angle), and 300 amps 90 VDC, TC <1ms. for the 7 and 10 amp fuses. NOTE: All values shown above are typical. • Device designed to carry rated current for four hours minimum. An operating current of 80% or less of rated current is recommended, with further derating required at elevated ambient temperatures. 0210 BU-SB10142 Page 1 of 2 Data Sheet 2003 OBSOLETE - Recommended replacement with MCRW, Data Sheet 4074 - OBSOLETE Subminiature Through Hole MCR Series, Fast Acting, Solid Matrix TIME CURRENT CURVE AMPERE RATING 10 1 .1 .01 .001 CURRENT IN AMPERES PACKAGING CODE Packaging Code Description Blank 10 units BK 500 units TR 2,500 pieces on tape and reel per EIA-296, 52.4mm spacing OC-2544 Rev. A 5/02 Visit us on the Web at www.cooperET.com 3601 Quantum Boulevard Boynton Beach, Florida 33426-8638 © Cooper Electronic Technologies 2002 Tel: +1-561-752-5000 Toll Free: +1-888-414-2645 Fax: +1-561-742-1178 This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper Electronic Technologies reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Cooper Electronic Technologies also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications. 0210 BU-SB10142 Page 2 of 2 Data Sheet 2003 TIME IN SECONDS .01 .1 1/16 1/8 1/4 3/8 1/2 1 3/4 1.0 1.5 2.0 2.5 3.0 4.0 5.0 10 7.0 10.0 100