EC-SYSTEMS Options 330 Switch power supplies 334 External commutation electronics for rail technology 338 Accessories: Temperature sensor / control module, pressure control, selection module, interface converter, ... 340 HMS controller 358 329 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information EC-SYSTEMS Options EC fans 24 / 48 VDC EC fan with integrated commutation electronics PWM and Lin 0-10 VDC red Linear input: 24 / 48 VDC < 1 VDC -> n=0 blue 1 VDC -> n min yellow 10 VDC -> n Control input Lin 0-10 VDC max PWM PWM input: white < 10% PWM -> n=0 Tach output 10% PWM -> n min 100% PWM -> n max EC fans 48 VDC Power supply 230 VAC / 48 VDC EC fan 48 VDC with integrated commutation electronics PWM and Lin 0-10 VDC red Linear input: 230 VAC, 50 / 60 Hz < 1 VDC -> n=0 blue 1 VDC -> n min 10 VDC -> n max yellow Optional board (built-in): PWM input: white < 10% PWM -> n=0 10% PWM -> n min Selector switch 3 speed steps 100% PWM -> n max Control input Lin 0-10 VDC or Constant air flow selector switch PC with interface RS485 / ebmBUS converter (RS485) EC fans Commutation electronics 650 W EC fan with external commutation electronics 650 W, 110 VDC (rail technology) 110 VDC PC with interface converter (RS485) Actual value 0-10 VDC (e.g. pressure, temperature, air flow, air speed, moisture, CO ) 2 Control input Lin 0-10 VDC Potentiometer for set values Tach output Alarm Controller enabling 10-100 VDC 10-253 VAC 330 EC fans (motor size 055) EC fan with integrated electronics with integrated commutation electronics 1~ 115 VAC or 230 VAC 50/60 Hz mains operation EC fans (motor size 074) with integrated commutation electronics Mains operation, 50 / 60 Hz 1~ 100 -130 VAC or 200 -277 VAC 50/60 Hz mains operation PC with interface converter (RS485) Control input 0-10 VDC / PWM Actual value input 0-10 VDC Supply for potentiometer 10 V Tach output Slave output EC fans (motor size 084) EC fan with integrated electronics with integrated commutation electronics 1~ 100 -130 VAC or 200 -277 VAC 50/60 Hz mains operation Mains operation, 50 / 60 Hz PC with interface converter (RS485) Control input 0-10 VDC / PWM Actual value input 0-10 VDC Supply for potentiometer 10 V Alarm Slave output 331 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information EC-SYSTEMS Options EC fans (motor size 084, ebmBUS) EC fan with integrated electronics with integrated commutation electronics 1~ 200-277 VAC, 50/60 Hz mains operation Mains operation, 50 / 60 Hz PC with interface converter (RS485) On/off and alarm output 15 V EC fans (motor size 112/150) EC fan with integrated electronics with integrated commutation electronics 1~ 200-277 VAC or 3~ 200-240 / 380-480 VAC 50/60 Hz mains operation Mains operation, 50 / 60 Hz PC with interface converter (RS485) Control input 0-10 VDC / PWM Actual value input 0-10 VDC Actual value input 4-20 mA Supply for external sensor 20 V Supply for potentiometer 10 V Alarm Slave output 332 EC-SYSTEMS: Customer PC with LISA Interface converter Electronics EC fan Networked EC fans with interface 5.1 control software and repeater converter and repeater Control software part no. 25711-2-0199 integrated electronics Interface converter part no. 21487-1-0174 max. 31 Features of control addresses software LISA 5.1 Power supply 150 W – Individual control Repeater and monitoring of part no. max. 7,905 fans 25708-1-0174 – Group-oriented arrangement of the fans – Level 1: Overview display for 10 floors max. 31 – Level 2: Overview addresses display for 255 groups integrated electronics – Level 3: Overview display for 31 fans within a group – Broadcast command for a group or all fans – Speed, temperature or pressure control – Alarm signal integrated electronics Repeater max. 31 addresses 333 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Switch power supply with PFC, basic version 48 VDC, 150 W / 300 W – General remarks: Switch power supply with an output power of 150 W / 300 W to supply 48 VDC EC motors from the 115 / 230 VAC mains. It is also possible to run several motors up to an overall power of 150 W / 300 W. Data on the 60 W switching power supply is available on request. – Function: Supply of an electrically insulated direct voltage of 48 VDC at the output when connected to the 115 / 230 V mains. The power supply is sustainably short-circuit proof, open-circuit proof and protected against overheating. An integrated EMC filter guarantees RFI suppression of the unit according to EN 61000-3-2. – Material: Housing made of stainless steel – Protection class: I – Type of protection: IP 20 (acc. to EN 60529) Nominal data Dimensions Type VAC Hz VDC W A kg ab c d e f CNW015-AB06 -01 1~ 115 50/60 48 150 3.10 0.7 187 176 167 50 110 1 CNW015-AB02 -01 1~ 230 50/60 48 150 3.10 0.7 187 176 167 50 110 1 CNW030-AC06 -01 1~ 100-120 50/60 48 300 6.25 1.3 272 260 251 66 112 2 CNW030-AC02 -01 1~ 200-277 50/60 48 300 6.25 1.3 272 260 251 66 112 2 subject to alterations – EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-1 – Product conforming to standards: EN 50178, CE – Approvals: UL/CSA (File No. E 181381) e 5 80 108 334 10 c f Nominal voltage b d a Frequency Output voltage Output P max. 1 Rated output current Mass Blower 1 Blower 2 exhaust air exhaust air Line side Motor side +48 +48 L N PE GND GND V V red blue red blue 335 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Switch power supply with PFC, RS485 and ebmBUS 48 VDC, 150 W / 300 W – General remarks: Switch power supply with an output power of 150 W / 300 W to supply 48 VDC EC motors from the 115 / 230 VAC mains. It is also possible to run several motors up to an overall power of 150 W / 300 W. Data on the 60 W switching power supply is available on request. – Function: Supply of an electrically insulated direct voltage of 48 VDC at the output when connected to the 115 / 230 V mains. The power supply is sustainably short-circuit proof, open-circuit proof and protected against overheating. An integrated EMC filter guarantees RFI suppression of the unit according to EN 61000-3-2. – Material: Housing made of stainless steel – Protection class: I – Type of protection: IP 20 (acc. to EN 60529) Nominal data Dimensions Type VAC Hz VDC W A kg ab c d e f CNW015-AB06 -05 1~ 115 50/60 48 150 3.10 0.7 187 176 167 50 110 1 CNW015-AB02 -05 1~ 230 50/60 48 150 3.10 0.7 187 176 167 50 110 1 CNW030-AC06 -05 1~ 100-120 50/60 48 300 6.25 1.3 272 260 251 66 112 2 CNW030-AC02 -05 1~ 200-277 50/60 48 300 6.25 1.3 272 260 251 66 112 2 subject to alterations – EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-1 – Product conforming to standards: EN 50178, CE – Approvals: UL/CSA (File No. E 181381) e – Technical features: Control board for RS485, ebmBUS and LISA functions 5 80 108 336 10 c f Nominal voltage b d a Frequency Output voltage Output P max. 1 Rated output current Mass Blower RS232 RS485 Interface converter To next switch power supply white yellow Line side Motor side Tach PWM RS485 RS485 2 x RJ45: PIN 5 - RS B PIN 6 - RS A +48 +48 L N PE GND GND V V red blue 337 ~ EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information External commutation electronics for rail technology, 110 VDC, 650 W – General remarks: For EC motors and fans with 3 cores and without integrated commutation electronics – Function: Commutation unit for three-core EC motors up to a power input of 650 W. Various basic functions are integrated: open loop speed control, closed loop speed control, RS485 interface. In combination with sensors, all control tasks as required in air technology can be executed. – Protection class: I – Type of protection: IP 20 (acc. to DIN EN 60529) – NB: Connected fans have to be designed for a rated voltage of 127 VDC! Nominal data Type VDC W A °C kg CEG 485-HB50 -01 110 650 5.9 -25 to +40 2.0 subject to alterations 169 – EMC / EMI: Acc. to EN 50155 and EN 50121 – Legislation: Low voltage directive 73/23/EEC, VDE 0160/EN 50178 – Design: • Motor output protected against short circuit phase to phase and conditionally phase to earth • 0-10 V input (Ri: 100 k�) 190 • 0-10 V input (Ri: 100 k�) for connection of external actual value input • RS485 interface (ebmBUS) • Floating alarm contact 250 VAC / 5A, during alarm, relay is released (low-active) • Wide voltage input for external controller enabling via RESET function • Tach output 179,5 • LED for operation and alarm mode green: unit on red: alarm • Setting of minimum and maximum values via potentiometer • Operational modes (to be set via DIP switch): Open loop speed control Closed loop speed control Controlling external parameters • Direction of motor rotation reversible – Connectors for external electronics: KL1 2-pole connector; centreline 7.5; Co. Wago part no.: 231-202/026-000 KL2A 6-pole connector; centreline 5; Co. Wago part no.: 231-106/026-000 KL2B 6-pole connector; centreline 5; Co. Wago part no.: 231-106/026-000 KL3A 2-pole connector; centreline 5; Co. Wago part no.: 231-102/026-000 KL3B 2-pole connector; centreline 5; Co. Wago part no.: 231-102/026-000 146,5 KL4 2-pole connector; centreline 5; Co. Wago part no.: 231-102/026-000 KL5A 5-pole connector; centreline 5; Co. Wago part no.: 231-105/026-000 KL5B 5-pole connector; centreline 5; Co. Wago part no.: 231-105/026-000 KL6 3-pole connector; centreline 7.5; Co. Wago part no.: 731-603 338 40 5,5 Nominal voltage Power input 1,5 63 64 63 1,5 2,2 P max. 1 193 68 Current draw Perm. amb. temp. Mass KL2B KL3B KL5B PE1 PE2 +18 Sensor +10 0-10 TW GND GND COM NC H+ H+ H- H- V 1 V V PTC RS RS RS RS An EN EN GND COM + - NO NO H1 H2 H3 U V W A B A B Tacho + - KL1 KL2A KL3A KL4 KL5A KL6 Connector Connection Assignment / function Connector Connection Assignment / function PE1 Ground connection KL3A NO Relay contact for alarm, make for failure PE2 Ground connection COM Relay contact for alarm KL1 + 110 VDC KL3B NC Relay contact for alarm, break for failure - 110 VDC COM Relay contact for alarm KL2A RS A Interface connection RS A KL4 EN + Enable input via RESET function RS B Interface connection RS B EN - Enable input via RESET function RS A Interface connection RS A KL5A H1 Hall-sensor 1 RS B Interface connection RS B H2 Hall-sensor 2 An, Tacho Tach output, open collector H3 Hall-sensor 3 GND Reference KL2 (for KL2 only) Shielding connection KL2B +18 V +18 V (non-stabilised, +20%, 20 mA) for supplying Shielding connection external sensors KL5B H+ Power supply for hall-sensors (+) Input for external sensor, Ri = 100 k� Sensor 1 H+ Power supply for hall-sensors (+) GND Reference KL2 (for KL2 only) TW / PTC Thermal switch or PTC connection +10 V +10 V (stabilised +/- 3 %, 25 mA) H- Power supply for hall-sensors (-) 0-10 V Input for set value 0 - 10 V, Ri = 100 k� H- Power supply for hall-sensors (-) GND Reference KL2 (for KL2 only) KL6 U Motor winding U V Motor winding V W Motor winding W 339 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Temperature sensor Nominal data Part no. VDC mA VDC mA k� °C kg 50005-1-0174 15-30 10 0-10 1.0 1.1 -20 to +80 0.02 subject to alterations +0,2 3 +0,5 Ø7 – Electr. connection: Ø3,5 red 15-30 VDC 84,7 yellow 0-10 VDC 45 output 37,5 6,5 38,5 Output (yellow) Core-end sleeve + (red) blue – (blue) 6 85 Temperature sensor – Output voltage depending on temperature: U/V 10 0 -20 80 Temp. °C Tolerance ±3 K 340 Ø4,9 13 8 5 3,3 ±0,1 1 2,5 6,9 Nominal voltage Current draw Output voltage +20 450 Output current Output impedance Temperature measuring range Mass Temperature control module Nominal data Part no. VDC mA VDC mA k� °C kg 50002-1-0174 18-60 10 2-10 0.1 6.8 +30 to +55 0.02 50003-1-0174 18-60 10 0-10 0.1 6.8 +10 to +45 0.02 subject to alterations +0,2 3 +0,5 Ø7 – Electr. connection: Ø3,5 red red 18-60 VDC Maximum ripple ± 3.5 % 84,7 yellow yellow 2-10 VDC Control input 47 K 45 or 0-10 VDC 0 - 10 VDC 37,5 output Counter I max. sink 6,5 10 mA Controller white Tach output, 680 � Alarm pulses per revolution 38,5 Speed display 47 V Output (yellow) Core-end sleeve + (red) blue blue – (blue) GND 6 85 Temperature control module Connection Fans – Control function: Both designs have "cooling" as control function U/V U/V 10 10 2 1 0 30 55 Temp. °C 01 60 45 Temp. °C 50002-1-0174 50003-1-0174 Tolerance ±3 K 341 Ø4,9 13 8 5 3,3 ±0,1 1 2,5 6,9 Nominal voltage Current draw Output voltage +20 450 Output current Output impedance Temperature control range Mass 47 K EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Pressure control with integrated pressure sensor – Functions: Integrated PID controller, day/night/linear set point preset, integrated set point potentiometer for day and night, external set point preset via potentiometer – Pressure sensor: 0-500 Pa, bursting strength 200 mbar, for non-aggressive gaseous media – Type of protection: IP 55 Nominal data Type VAC Hz VDC Pa °C CCC 000-AC04 -01 1~ 100-277 50/60 20 @ 50 mA 50-500 -25 to +60 subject to alterations 167 162 195 180±0,4 pressure controller IP55 100-277 VAC 50/60 Hz pressure range 0-500 Pa Ø5,5 7,5 342 125 89,5 43 35,5 Nominal voltage range Frequency 10 95±0,2 1,5 115 10,5 Nominal voltage, alternative Pressure control range Perm. amb. temp. Fan Set value potentiometer Selector switch Day Linear Night Mains Alarm ST1 ST2 ST7 ST8 ST3 ST4 Line terminals Control terminals Connector Connection Assignment / function Connector Connection Assignment / function ST1 PE Protective earth ST3 20 V IN DC voltage supply (optional), L Mains 50/60 Hz, phase with reverse polarity protection N Mains 50/60 Hz, neutral GND GND ST2 PE Protective earth ST4 Tach Tach output from fan L Mains 50/60 Hz, phase OUT Control voltage for fan, 0-10 V N Mains 50/60 Hz, neutral GND GND ST7 NC Relay contact for alarm, break for failure +10 V Set value potentiometer, COM Relay contact for alarm supply 10 V (-10 %), 10 mA ST8 NC Relay contact for alarm, break for failure 0-10 V PWM Set value potentiometer COM Relay contact for alarm GND Set value potentiometer Day Selector switch terminal GND Selector switch terminal Night Selector switch terminal GND Selector switch terminal 343 PE L N PE L N NC COM NC COM 20 V IN GND Tach OUT GND +10 V 0-10 V PWM GND Day GND Night GND EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Selection module for 3 speeds – General remarks: Using an external selector switch, one of three preset speeds can be chosen. Presetting is done via one integrated potentiometer each. – Material: Plastics – Type of protection: IP 20 Type CBC 000-AE04 -01 subject to alterations 50 344 90 24 – Electr. Connection connection: fan red +10 V yellow 0-10 V output Fan blue GND Connection Selector switch selector switch +10 V Day Night Party 345 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Interface converter RS232 - RS485 – General remarks: This interface converter permits bi-directional connection of RS232 devices (laptop or PC) with ebmBUS devices (electronic commutation units with RS485 interface) – Safety: Electrical insulation between the RS232 and RS485 side is provided – Material: Plastic housing for standard rail mounting according to DIN EN 50022-35 – Status display: Via LEDs green: supply voltage OK red: data exchange Nominal data Part no. VAC VAC / VDC mA kg 21487-1-0174 1~ 230 12-24 150 0.4 subject to alterations – Mode of operation: RS485 2-wire mode with echo and automatic control RS232 RS485 – Galvanic insulation: Min. 1kV insulation voltage between RS232 and RS485 interfaces and between power supply and interfaces – ESD immunity: Up to 15 kV (acc. to IEC 801-2, Stage 4) – Delivery scope: • Interface converter • Supply plug unit (230 VAC / 12 VDC, 500 mA) • Adaptor leads with 2 x 9-pole SUB-D sockets • Adaptor leads with 9-pole SUB-D socket • Screw terminal RS485 75 346 ML+ Nominal voltage power supply 105 22 Supply voltage Current draw at no-load operation Mass (incl. PS) PWR TXD RXD RS485 RS422 Interface converter RS232 - RS485 – General remarks: This interface converter permits bi-directional connection of RS232 devices (laptop / PDA) with ebmBUS devices (electronic commutation units with RS485 interface). Power supplied by RS232 of the laptop / PDA. – Material: Plastic housing – Status display: Via LEDs PWR: Power supply TXD: Data transfer (send) RXD: Data transfer (receive) Nominal data Part no. kg 21495-2-0174 0.1 subject to alterations – Mode of operation: RS485 2-wire mode with echo and automatic control TX+ TX- GND RX+ RX- – Delivery scope: Interface converter, English-language operating manual TRX+TRX- – Electrical terminals: Screw terminal, TRX+ = RSA, TRX– = RSB 37 347 74 19 Mass EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Ø4.3 RS485 repeater – General remarks: The physical RS485 repeater is used for the connection of two segments on an RS485 basis. It can split a segment with network bus wires that are too long, or with too many nodes into two smaller, standardised units. A maximum of 31 nodes can be connected to the repeater. – Installation: The repeater housing is mounted on the wall or in the cable duct with two screws (Ø 4 mm) or with cable ties. – Material: Housing made of galvanised sheet steel – Type of protection: IP 20 according to DIN EN 60529 Nominal data Part no. VAC Hz VA °C °C kg 25708-1-0174 1~ 200-277 50/60 < 3 0 to +50 -20 to +70 0.3 subject to alterations – Type of transceiver: 2 x ANSI standard RS485 transceiver 38 – Galvanic insulation: Operating insulation 500 V between both channels – Network connection: Screw terminals – Mains connection: Wieland connector GST 18/3 (part of delivery) – Pin configuration of network: Pin No. Assignment / function 1 - 4 not assigned 87 654 3 2 1 8 7 6 5 4 3 2 1 5 Connection RS485, line B A A B B 6 Connection RS485, line B BUS1 BUS2 7, 8 not assigned (each looped through within BUS1 and BUS2) 12 34567 8 12 3 4 5 6 7 8 LED 30 Supply connection 348 50 200 Bus1 Bus2 Bus1 Bus2 Mating connector GST 18/3 Wieland Bamberg screw terminal Supply voltage 3 190 Frequency Power input Perm. operating temp. Perm. storage temp. Mass RS485 terminal box with lead connections for centrifugal fans with EC motor size 084 (ebmBUS, RS485) – General remarks: RS485 terminal box with • 2x RJ45 sockets for ebmBUS • ebmBUS line with Molex Mini-Fit female connector for connection to the motor • 3-pole 4-pin unit connector with AMP Mate-N-Lock female connector to connect to motor • Mode of operation display (LED2 green) and alarm display (LED 1 red) – Delivery scope: • Terminal Box • Supply line (800 mm) • ebmBUS line (800 mm) – Material: ABS (fire rating V0 according to UL) Part no. 54002-4-1040 subject to alterations – Pin configuration of supply lead: Colour Assignment / function green/yellow PE black 2 N 57 black 1 L 61.6 73 45.4 61 – Pin configuration of ebmBUS lead: Colour Assignment / function yellow RS A white RS B red Operation: +15 V Alarm: 0 V blue Operation: 0 V Alarm: +15 V – Pin configuration of RJ45 sockets: Pin No. Assignment / function Mounting dimensions 5 RS B 58 6 RS A 61 349 88 87 111 99 4 99 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Hand-held control terminal – General remarks: Terminal to control networked fans and to set their parameters; RS485 (ebmBUS) – Type of protection: IP 20 (acc. to DIN EN 60529) – Protection class: III – Display: Plain text LCD, 2x8 characters – Accumulator and charging electronics: 2 x round cell R6 DIN 40863 NiMH 1,500 mAh, operating time approx. 40 hrs, standby time approx. 100 days, charging time max. 4 hrs. – Parts included in delivery: Hand-held control terminal, power supply and accumulator unit, BUS cable, 2 x round cell R6 NiMH 1,500 mAh Nominal data Type VAC Hz VDC °C °C kg CBC 000-AB06 -01 1~ 100-240 50/60 12 0 to +45 -20 to +65 0.4 subject to alterations 68 44 350 95 Nominal voltage range power supply Frequency Supply voltage Perm. amb. temp. Perm. storage temp. Mass 351 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Speed setting device with housing – Material: Housing made of plastic – Type of protection: IP 54 – Design: The speed setting device can be operated with the entire range of ebm-papst EC fans. It is supplied with current via the fan's DC output and supplies a 0-10 V signal that allows infinitely variable open loop speed control. The control also permits fan speed measurement using a multimeter equipped with a frequency meter (for which a tach output is given from the fan). – Cable inputs: 4 x M16 or M20 – Mounting holes: Suitable for 4 mm mounts Nominal data Type VDC mA k� °C kg CLC 000-AE04 -01 10 1.1 0-10 Lin 50 0.10 subject to alterations – Speed measurement: Connect a frequency meter to the connection points 65 (labelled + and -) on the PCB board. The fan has an output of 1 pulse per revolution, so that the measured frequency can be converted into rpm using the following equation: rpm = frequency (Hz) x 60 – Comment: • A single controller can be used to control multiple fans with the same speed setting. • The connection to the controller is made using four screw connections or one Molex connection (adaptor lead available). • If the tach cable is required, this device can only be connected to one fan. Note that in rare operating cases, it is possible that permanent connection of the tach cable can cause a slight decrease in the maximum speed. 50 25 + meter connection – meter connection 352 50 58 26 65 Supply voltage Max. current draw Resistance Perm. amb. temp. Mass – Electr. connection: red +10 V yellow +10 V Control Control blue GND GND Tacho white Tacho Fan 2 Fan 1 353 red yellow blue white red yellow blue white EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information Speed setting device without housing – Design: The speed setting device can be operated with the entire range of ebm-papst EC fans. It is supplied with current via the fan's DC output and supplies a 0-10 V signal that allows infinitely variable open loop speed control. The control also permits fan speed measurement using a multimeter equipped with a frequency meter (for which a tach output is given from the fan). – Mounting hole: 10 mm Nominal data Type VDC mA k� °C kg CLC 000-AD04 -01 10 1.1 0-10 Lin 50 0.05 subject to alterations – Speed measurement: Connect a frequency meter to the connection points 36 28 (labelled + and -) on the PCB board. The fan has an output of 1 pulse per 4 x Ø3,5 revolution, so that the measured frequency can be converted into rpm using the following equation: rpm = frequency (Hz) x 60 – Comment: • A single controller can be used to control multiple fans with the same speed setting. • The connection to the controller is made using four screw connections or one Molex connection (adaptor lead available). • If the tach cable is required, this device can only be connected to one fan. Note that in rare operating cases, it is possible that permanent connection of the tach cable can cause a slight decrease in the maximum speed. + meter connection – meter connection 354 50 36 22 28 12 Supply voltage Max. current draw Resistance Perm. amb. temp. Mass – Electr. connection: red +10 V yellow +10 V Control Control blue GND GND Tacho white Tacho Fan 2 Fan 1 355 red yellow blue white red yellow blue white EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information LISA Control software for EC-SYSTEMS – Version: LISA 5.1 – Features: • Individual control and monitoring of 7,905 fans • Group-oriented arrangement of the fans • Level 1: Overview display for 10 floors • Level 2: Overview display for 255 groups within a floor • Level 3: Overview display for 31 fans within a group • Broadcast command for one group or all fans • Speed, temperature or pressure control • Error message Part no. 25711-2-0199 subject to alterations – Suitable for: EC motors and electronics with ebmBUS – System requirements: Windows 2000 / XP 356 Fan Control Control software & accessories for Pocket PCs / PDAs – Version: Fan Control 1.00 – Features: • Managing up to 31 fans • Setting pre-set values and indicating actual values • Setting parameters for PID control • Setting fan address • Setting mode of operation (heating/cooling) • Alarm diagnosis • Language selection for user interface Part no. 21500-1-0174 subject to alterations – Delivery scope: Installation-CD, interface converter (RS232-RS485), BUS cable, installation instruction and detailed manual (PDF). The Pocket PC / PDA and compatible serial communication cables are not included in the scope of delivery. – Suitable for: EC motors and electronics with ebmBUS – System requirements: Pocket PC / PDA with Windows Mobile 5.0, RS232 interface, and serial communication cable. – Compatible Pocket PCs / PDAs: (as of 2006-09-14) • Hewlett-Packard rx1950 • Hewlett-Packard hx2190 • Fujitsu-Siemens Pocket Loox C550 Set and actual values Mode of operation • Dell Axim x51v (624 MHz) Refer to our website at www.ebmpapst.com/downloads for a continuously updated list of approved Pocket PCs / PDAs along with the suitable serial communication cables. Fan address Graphic setting 357 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information HMS controller – General remarks: The HMS controller is governed by a microprocessor and is specifically designed for Heat Management Systems (= HMS). This controller allows for an almost limitless programming variety as regards customer-specific fan speed / temperature profiles. Moreover, this controller offers a multitude of the most diverse alarm configurations. Our HMS controller has been specially designed and adjusted to the product range of ebm-papst in Mulfingen. Thus, any size of our fans or blowers can be used. The most diverse of applications needing temperature-dependent control are possible. Among these are applications in telecommunication and the IT industry, in refrigeration and air-conditioning as well as in specific industrial plants and systems. Nominal data Type VDC W W A °C kg CCC 000-AA05 -03 16-57 10 130 0.175 -40 to +70 0.15 subject to alterations (1) without fans (2) per fan at nominal voltage – Features: 100 • 4 fan speed / temperature characteristics that can be programmed independently 81 of each other • 2 programmable no-frost relays for connecting 115 / 230 VAC heating devices • 5 programmable alarm relays (with time lag): - Temperature alarm (over / under-temperature) - Fan good / bad alarm programming - Temperature sensor alarm - Programmable depending on signal inputs • 4 programmable status outputs (with time lag): - With "open collector" design to connect optical or acoustic displays / alarms - Each fan speed can be set individually • 4 signal inputs for external switches / limit switches • Connection of two independent temperature sensors (NTCs) possible • RS232 interface galvanic insulated • Selective protection of each fan • Programming via Windows software (terminal program version 15 ff.: part no. 25710-2-0199) – Requirements: • Supply voltage of HMS controller: 16-57 VDC • Fans with standard interface - 24 / 48 VDC fan voltage - PWM / linear control input (0-10 V) - Open collector tach output • NTC with R = 33 k� (EPCOS type M 891/33k/J) 25 • System requirements: Windows 2000 / XP – Safety: According to EN 50178 – EMC / EMI: Interference immunity EN 61000, interference emission EN 50081-1 358 160 70 75.5 7.25 Supply voltage (1) Power input , max. (2) Power input , max. (1) Current draw max. Perm. amb. temp. Mass 16 - 57 VDC - + L1 K1 F1 3,15 A * / 250 V Heater 1 H1 Fan 1 PWM Hall + - H2 F6 10 A * / 250 V F2 3,15 A * / 250 V Fan 2 K2 N Heater 2 PWM Hall + - N F3 3,15 A * / 250 V F7 10 A * / 250 V Fan 3 N PWM Hall + - F4 3,15 A * / 250 V Alarm 1 Alarm 3 Alarm 5 Alarm 2 Alarm 4 Fan 4 PWM Hall + K4 K5 K6 K7 - K3 Alarm Status contact NTC 1 NTC 2 F5 3,15 A * / 250 V 1 2 3 1 2 3 4 1 1 4 DTR GND RS-232 RD TD RTS electrically insulated 1 1 1 * time lag fuse ê ê designation 9-pole Sub-D 24357 0-57 V / 10 mA 359 EC axial AC axial AC axial AC axial General Contacts Technology Accessories EC-SYSTEMS ESM Q-motor EC axial fans AC axial fans S series A series K series S series information 360