Data Sheet April 11, 2013 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75V Input; 14.0V Output; 17A Output Current dc dc Features BARRACUDA SERIES™  Compliant to RoHS EU Directive 2002/95/EC (-Z versions)  Compatible with reflow pin/paste soldering process  High and flat efficiency profile – 95.4% at 14.0V , dc 55% load to 90% output  Wide Input voltage range: 36-75V dc  Delivers up to 17A output current dc  Tightly regulated output voltage  Low output ripple and noise  No reverse current during prebias start-up or shut- down  Industry standard, DOSA compliant, Eight brick: 58.4 mm x 22.8 mm x 11.3 mm (2.30 in x 0.90 in x 0.44 in) RoHS Compliant  Constant switching frequency  Positive Remote On/Off logic Applications  Output over current/voltage protection  Distributed power architectures  Over temperature protection  Intermediate bus voltage applications  Wide operating temperature range (-40°C to 85°C) †  DSL systems  UL* 60950-1, 2nd Ed. Recognized, CSA C22.2 No. ‡ 60950-1-07 Certified, and VDE (EN60950-1, 2nd  Ed.) Licensed §  CE mark 2006/96/EC directives  Meets the voltage and current requirements for ETSI Options 300-132-2 and complies with and licensed for Basic insulation rating per EN60950-1  Negative Remote On/Off logic (1=option code,  2250 Vdc Isolation tested in compliance with IEEE factory preferred) 802.3¤ PoE standards  Auto-restart after fault shutdown (4=option code,  ISO** 9001 and ISO14001 certified manufacturing factory preferred) facilities  Base plate option (-H=option code) Description The EBVW017A0S14R0 series of dc-dc converters are a new generation of DC/DC power modules designed to support 14.0V DSL applications, as distributed power architectures. The EBVW017A0S14R0 series operate from an dc input voltage range of 36 to 75V , and provide up to 17A output current at 14.0V output voltage, and 240W output dc dc power in a DOSA standard eighth brick. The converter incorporates digital control, synchronous rectification technology, and innovative packaging techniques to achieve efficiency reaching 95.5% peak at 14.0V output. This dc leads to lower power dissipations such that for many applications a heat sink is not required. Standard features include on/off control, output overcurrent and over voltage protection, over temperature protection, input under and over voltage lockout. Optional features include a base plate for heat sink or cold wall applications. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. Built- in filtering for both input and output minimizes the need for external filtering. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment . All of the required procedures of end-use equipment should be followed. ¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated. ** ISO is a registered trademark of the International Organization of Standards. Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the Data Sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Device Symbol Min Max Unit Input Voltage* Continuous V -0.3 75 V IN dc Operating transient ≤ 100mS 100 V dc Operating Input transient slew rate, 50V to 75V IN IN (Output may exceed regulation limits, no protective - - 10 V/µs shutdowns shall activate, C =220μF to C ) O O, max Non- operating continuous V 80 100 V IN dc Operating Ambient Temperature All T -40 85 °C A (See Thermal Considerations section) Storage Temperature All T -55 125 °C stg I/O Isolation Voltage (100% factory Hi-Pot tested) All 2250 V   dc * Input over voltage protection will shutdown the output voltage, when the input voltage exceeds threshold level. Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage VIN 36 48 75 Vdc Maximum Input Current I - - 7 A IN,max dc (V =0V to 75V, I =I) IN O O, max Input No Load Current All I 50 mA IN,No load (V = V , I = 0, module enabled) IN IN, nom O Input Stand-by Current All I 25 mA IN,stand-by (V = V , module disabled) IN IN, nom External Input Capacitance All 100 - - μF 2 2 Inrush Transient All It - - 1 A s Input Terminal Ripple Current (Measured at module input pin with maximum specified input capacitance and ൏ 500uH inductance All - 900 - mA rms between voltage source and input capacitance C =220uF, 5Hz to 20MHz, V = 48V, I = I ) IN IN O Omax Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; V = 48V, All - 24 - mA IN p-p I = I ; see Figure 12) O Omax Input Ripple Rejection (120Hz) All - 50 - dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 15 A (see Safety Considerations section). Based on the information provided in this Data Sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s Data Sheet for further information. LINEAGE POWER 2 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Voltage Set-point All V 13.97 14.00 14.03 V O, set dc (V =V , I =10A, T =25°C) IN IN,nom O A Output Voltage (Over all operating input voltage(40V to 75V), resistive All V 13.71  14.29 V O dc load, and temperature conditions until end of life) Output Voltage (V =36V, T = 25ºC) All V 10.8 V IN A O   dc Output Regulation (VIN, min=46V) Line (V =V to V) All 0.2 % V IN IN, min IN, max   O, set Load (I =I to I) All  0.2  O O, min O, max % V O, set Temperature (T = -40ºC to +85ºC) All  2  % V A O, set Output Ripple and Noise on nominal output (V =V and I =I to I , tested with a 1.0 μF IN IN, nom O O, min O, max ceramic, 10 μF aluminum and 220μF polymer capacitor across the load.) RMS (5Hz to 20MHz bandwidth) All 70 mV   rms Peak-to-Peak (5Hz to 20MHz bandwidth) All  200  mV pk-pk External Output Capacitance All C 220 10,000 μF O  Output Current All I 0 17 A o dc Output Current Limit Inception All I  19  A O, lim dc Efficiency (V =V , V = V , T=25°C) IN IN, nom O O,set A I = 100% I All η 95.5 % O O, max I = 40% - 100% I All η 94.0 % O O, max Switching Frequency (primary MOSFETs) f 150 kHz sw (Output Ripple 2X switching frequency) Dynamic Load Response (dIo/dt=1A/10s; V =V ,nom; T =25°C; tested with a in in A 10 μF ceramic and 1x 470μF polymer capacitor across the load.) Load Change from Io= 50% to 75% of Io,max: V  750  pk Peak Deviation All mV pk t 800 s __ __ Settling Time (Vo<10% peak deviation) s Load Change from Io= 75% to 50% of Io,max:  Peak Deviation V __ 750 mV pk pk __ Settling Time (Vo<10% peak deviation) t __ 800 s s Isolation Specifications Parameter Symbol Min Typ Max Unit Isolation Capacitance C  1000  pF iso Isolation Resistance R 10   MΩ iso General Specifications Parameter Device Symbol Typ Unit Calculated Reliability Based upon Telcordia SR-332 All MTBF 4,169,213 Hours Issue 2: Method I, Case 1, (I =80%I , T =40°C, O O, max A 9 All FIT 239.9 10 /Hours Airflow = 200 lfm), 90% confidence Weight – Open Frame 29.5 (1.04) g (oz.) Weight – with Baseplate option 39.0 (1.38) g (oz.) LINEAGE POWER 3 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit Remote On/Off Signal Interface (V =V to V , Signal referenced to V IN IN, min IN, max IN- terminal) Negative Logic: device code suffix “1” Logic Low = module On, Logic High = module Off Positive Logic: No device code suffix required Logic Low = module Off, Logic High = module On Logic Low Specification On/Off Thresholds: Remote On/Off Current – Logic Low All I 280  310 μA on/off Logic Low Voltage All V -0.3  0.8 V on/off dc Logic High Voltage – (Typ = Open Collector) All V 2.0 14.5 V on/off  dc Logic High maximum allowable leakage current All I   10 μA on/off (V = 2.0V) on/off Maximum voltage allowed on On/Off pin All V 14.5 V on/off   dc Turn-on Delay and Rise Time (I =I ) O O, max T =Time until V = 10% of V from either delay O O,set T delay, Enable All 160 ms   application of Vin with Remote On/Off set to On with Vin (Enable with Vin); or operation of Remote On/Off T , from Off to On with Vin already applied for at least delay Enable All   40 ms 150 milli-seconds (Enable with on/off). with on/off T =Time for V to rise from 10% to 90% of V , rise O O,set For C >5000uF, I must be < 50% I during O O O, max All T   40 ms rise T . rise Prebias Output Load Performance: Back Bias current sunk by output during start-up All   50 mA Back Bias current sunk by output during shut-down   50 mA Output Overvoltage Protection All V 17.0 V O,limit dc Overtemperature Protection All T  140  °C ref (See Feature Descriptions) Input Undervoltage Lockout Turn-on Threshold 35 36 V  dc Turn-off Threshold 32 33.5 V  dc Input Overvoltage Lockout Turn-off Threshold  85 86 V dc Turn-on Threshold 76 79  V dc LINEAGE POWER 4 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Characteristic Curves The following figures provide typical characteristics for the EBVW017A0S14R0 (14.0V, 17A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. INPUT VOLTAGE, V (V) TIME, t (20 ms/div) O Figure 1. Typical Input Characteristic at Room Figure 4. Typical Start-Up Using Remote On/Off with Temperature. Vin applied, negative logic version shown. OUTPUT CURRENT, I (A) TIME, t (1 ms/div) O Figure 2. Typical Converter Efficiency Vs. Output Figure 5. Typical Transient Response to Step change current at Room Temperature. in Load from 25% to 50% to 25% of Full Load at 48 Vdc Input and 220uF Aluminum Cap. TIME, t (40 ms/div) TIME, t (1 ms/div) Figure 3. Typical Start-Up Using Vin with Remote Figure 6. Typical Transient Response to Step Change On/Off enabled, negative logic version shown. in Load from 50% to 75% to 50% of Full Load at 48 Vdc Input and 220uF Aluminum Cap. LINEAGE POWER 5 OUTPUT VOLTAGE INPUT VOLTAGE V (V) (5V/div) V (V) (20V/div) EFFCIENCY, η (%) INPUT CURRENT, I (A) O IN i OUTPUT CURRENT OUTPUT VOLTAGE OUTPUT VOLTAGE On/Off VOLTAGE OUTPUT CURRENT OUTPUT VOLTAGE I (A) (5A/div) V (V) (500mV/div) V (V) (5V/div) V (V) (2V/div) I (A) (5A/div) V (V) (500mV/div) O O O ON/OFF O O Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Characteristic Curves (continued) INPUT VOLTAGE, V (V) OUTPUT CURRENT, I (A) in O Figure 7. Typical Output Voltage Regulation vs. Input Figure 8. Typical Output Voltage Regulation vs. Output Voltage at Room Temperature. Current at Room Temperature. 40 Vin 48 Vin 75 Vin TIME, t (2s/div) Figure 9. Typical Output Ripple and Noise at Room Temperature I = I and and C . o o,max OMin LINEAGE POWER 6 OUTPUT VOLTAGE, V (V) OUTPUT VOLTAGE, O V (V) (100mV/div) O Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Test Configurations Design Considerations Input Source Impedance The power module should be connected to a low ac-impedance source. A highly inductive source impedance can affect the stability of the power module. For the test configuration in Figure 12, a 220μF electrolytic capacitor, C , (ESR<0.7 at 100kHz), mounted close to the power in module helps ensure the stability of the unit. If the module is subjected to rapid on/off cycles, a 330μF input capacitor is required. Consult the factory for further application guidelines. Safety Considerations Note: Measure input reflected-ripple current with a simulated source inductance (LTEST) of 12 µH. Capacitor CS offsets For safety-agency approval of the system in which the possible battery impedance. Measure current as shown above. power module is used, the power module must be installed in compliance with the spacing and separation Figure 12. Input Reflected Ripple Current Test Setup. requirements of the end-use safety agency standard, i.e., nd nd UL60950-1 2 Ed., CSA C22.2 No. 60950-1 2 Ed., and nd VDE0805-1 EN60950-1 2 Ed. If the input source is non-SELV (ELV or a hazardous voltage greater than 60 Vdc and less than or equal to 75Vdc), for the module’s output to be considered as meeting the requirements for safety extra-low voltage (SELV), all of the following must be true:  The input source is to be provided with reinforced insulation from any other hazardous voltages, including the ac mains.  One V pin and one V pin are to be grounded, or IN OUT both the input and output pins are to be kept floating. Note: Use a 1.0 µF ceramic capacitor and a 10 µF aluminum or  The input pins of the module are not operator accessible. tantalum capacitor. Scope measurement should be made using a BNC socket. Position the load between  Another SELV reliability test is conducted on the whole 51 mm and 76 mm (2 in. and 3 in.) from the module. system (combination of supply source and subject module), as required by the safety agencies, to verify that under a single fault, hazardous voltages do not Figure 13. Output Ripple and Noise Test Setup. appear at the module’s output. Note: Do not ground either of the input pins of the module CONTACT AND DISTRIBUTION LOSSES without grounding one of the output pins. This may allow a non-SELV voltage to appear between the VO1 VI(+) output pins and ground. IO II LOAD The power module has safety extra-low voltage (SELV) SUPPL Y outputs when all inputs are SELV. The input to these units is to be provided with a maximum VI(–) VO2 15 A fast-acting (or time-delay) fuse in the unearthed lead. CONT ACT RESIST ANCE The power module has internally generated voltages Note: All measurements are taken at the module terminals. When exceeding safety extra-low voltage. Consideration should socketing, place Kelvin connections at module terminals to avoid be taken to restrict operator accessibility. measurement errors due to socket contact resistance. Figure 14. Output Voltage and Efficiency Test Setup. LINEAGE POWER 7 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc causes the output voltage to rise above the limit in the Feature Descriptions Specifications Table, the module will shut down and remain Overcurrent Protection latched off. The overvoltage latch is reset by either cycling the input power, or by toggling the on/off pin for one To provide protection in a fault output overload condition, second. If the output overvoltage condition still exists when the module is equipped with internal current-limiting the module restarts, it will shut down again. This operation circuitry and can endure current limiting continuously. If the will continue indefinitely until the overvoltage condition is overcurrent condition causes the output voltage to fall corrected. greater than 4.0V from V , the module will shut down and o,set A factory configured auto-restart option (with overcurrent remain latched off. The overcurrent latch is reset by either and overvoltage auto-restart managed as a group) is also cycling the input power or by toggling the on/off pin for one available. An auto-restart feature continually attempts to second. If the output overload condition still exists when the restore the operation until fault condition is cleared. module restarts, it will shut down again. This operation will continue indefinitely until the overcurrent condition is Overtemperature Protection corrected. These modules feature an overtemperature protection A factory configured auto-restart option (with overcurrent circuit to safeguard against thermal damage. The circuit and overvoltage auto-restart managed as a group) is also shuts down the module when the maximum device available. An auto-restart feature continually attempts to reference temperature is exceeded. The module will restore the operation until fault condition is cleared. automatically restart once the reference temperature cools by ~25°C. Remote On/Off Input Under/Over voltage Lockout The module contains a standard on/off control circuit At input voltages above or below the input under/over reference to the V (-) terminal. Two factory configured IN voltage lockout limits, module operation is disabled. The remote on/off logic options are available. Positive logic module will begin to operate when the input voltage level remote on/off turns the module on during a logic-high changes to within the under and overvoltage lockout limits. voltage on the ON/OFF pin, and off during a logic low. Negative logic remote on/off turns the module off during a Thermal Considerations logic high, and on during a logic low. Negative logic, device code suffix "1," is the factory-preferred configuration. The The power modules operate in a variety of thermal On/Off circuit is powered from an internal bias supply, environments and sufficient cooling should be provided to derived from the input voltage terminals. To turn the power help ensure reliable operation. module on and off, the user must supply a switch to control Thermal considerations include ambient temperature, the voltage between the On/Off terminal and the V (-) IN airflow, module power dissipation, and the need for terminal (V ). The switch can be an open collector or on/off increased reliability. A reduction in the operating equivalent (see Figure 15). A logic low is V = -0.3V to on/off temperature of the module will result in an increase in 0.8V. The typical I during a logic low (Vin=48V, On/Off on/off reliability. The thermal data presented here is based on Terminal=0.3V) is 147µA. The switch should maintain a physical measurements taken in a wind tunnel. logic-low voltage while sinking 310µA. During a logic high, Heat-dissipating components are mounted on the top side the maximum V generated by the power module is on/off of the module. Heat is removed by conduction, convection 8.2V. The maximum allowable leakage current of the and radiation to the surrounding environment. Proper switch at V = 2.0V is 10µA. If using an external voltage on/off cooling can be verified by measuring the thermal reference source, the maximum voltage Von/off on the pin is 14.5V temperature (TH ). Peak temperature (TH ) occurs at the x x with respect to the V (-) terminal. IN position indicated in Figure 18 and 19. For reliable If not using the remote on/off feature, perform one of the operation this temperature should not exceed the listed following to turn the unit on: temperature threshold. For negative logic, short ON/OFF pin to V (-). IN For positive logic: leave ON/OFF pin open. Figure 18. Location of the thermal reference temperature TH . Do not exceed 113 °C. 1 Figure 15. Remote On/Off Implementation. Output Overvoltage Protection The module contains circuitry to detect and respond to output overvoltage conditions. If the overvoltage condition LINEAGE POWER 8 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Figure 19. Location of the thermal reference temperature TH for Base Plate module. Do not exceed 2 110 °C. LOCAL AMBIENT TEMPERATURE, T (C) A Figure 22. Output Current Derating for the Base Plate EBVW017A0S14R0xx-H and 0.25” heat sink in the Transverse Orientation; Airflow Direction from Vin(-) to Vin(+); Vin = 48V. The output power of the module should not exceed the rated power for the module as listed in the Ordering Information table. Although the maximum temperature of the power modules is TH , you can limit this temperature to a lower value for x extremely high reliability. Please refer to the Application Note “Thermal Characterization Process For Open-Frame Board-Mounted LOCAL AMBIENT TEMPERATURE, T (C) A Power Modules” for a detailed discussion of thermal aspects including maximum device temperatures. Figure 20. Output Current Derating for the Open Frame EBVW017A0S14R0 in the Transverse Heat Transfer via Convection Orientation; Airflow Direction from Vin(-) to Vin(+); Vin = 48V. Increased airflow over the module enhances the heat transfer via convection. The thermal derating of figures 20 through 22 show the maximum output current that can be delivered by each module in the indicated orientation without exceeding the maximum TH temperature versus x local ambient temperature (T ) for air flows of, Natural A Convection, 1 m/s (200 ft./min), 2 m/s (400 ft./min). Layout Considerations The EBVW020 power module series are low profile in order to be used in fine pitch system card architectures. As such, component clearance between the bottom of the power module and the mounting board is limited. Avoid placing copper areas on the outer layer directly underneath the power module. Also avoid placing via interconnects underneath the power module. For additional layout guide-lines, refer to FLT007A0Z Data LOCAL AMBIENT TEMPERATURE, T (C) A Sheet. Figure 21. Output Current Derating for the Base Plate EBVW017A0S14R0xx-H in the Transverse Orientation; Airflow Direction from Vin(-) to Vin(+); Vin = 48V. LINEAGE POWER 9 OUTPUT CURRENT, I (A) OUTPUT CURRENT, I (A) O O OUTPUT CURRENT, I (A) O Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Through-Hole Lead-Free Soldering Information The RoHS-compliant, Z version, through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. The non-Z version products use lead-tin (Pb/Sn) solder and RoHS-compliant components. Both version modules are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant, pure tin finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free Figure 23. Recommended linear reflow profile using solder pot is 270C max. Not all RoHS-compliant through- Sn/Ag/Cu solder. hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is MSL Rating needed, please consult with your Lineage Power representative for more details. The EBVW017A0S14R0 modules have a MSL rating of 2a. Reflow Lead-Free Soldering Information Storage and Handling The RoHS-compliant through-hole products can be The recommended storage environment and handling processed with the following paste-through-hole Pb or Pb- procedures for moisture-sensitive surface mount packages free reflow process. is detailed in J-STD-033 Rev. A (Handling, Packing, Max. sustain temperature : Shipping and Use of Moisture/Reflow Sensitive Surface 245C (J-STD-020C Table 4-2: Packaging Mount Devices). Moisture barrier bags (MBB) with 3 Thickness>=2.5mm / Volume > 2000mm ), desiccant are required for MSL ratings of 2 or greater. Peak temperature over 245C is not suggested due to the These sealed packages should not be broken until time of potential reliability risk of components under continuous use. Once the original package is broken, the floor life of high-temperature. the product at conditions of 30°C and 60% relative Min. sustain duration above 217C : 90 seconds humidity varies according to the MSL rating (see J-STD- Min. sustain duration above 180C : 150 seconds 025A). The shelf life for dry packed SMT packages will be Max. heat up rate: 3C/sec a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40° C, < 90% relative Max. cool down rate: 4C/sec humidity. In compliance with JEDEC J-STD-020C spec for 2 times reflow requirement. Post Solder Cleaning and Drying Pb-free Reflow Profile Considerations BMP module will comply with J-STD-020 Rev. C Post solder cleaning is usually the final circuit-board (Moisture/Reflow Sensitivity Classification for assembly process prior to electrical board testing. The Nonhermetic Solid State Surface Mount Devices) for both result of inadequate cleaning and drying can affect both the Pb-free solder profiles and MSL classification reliability of a power module and the testability of the procedures. BMP will comply with JEDEC J-STD-020C finished circuit-board assembly. For guidance on specification for 3 times reflow requirement. The suggested appropriate soldering, cleaning and drying procedures, Pb-free solder paste is Sn/Ag/Cu (SAC). The refer to Lineage Power Board Mounted Power Modules: recommended linear reflow profile using Sn/Ag/Cu solder is Soldering and Cleaning Application Note (AP01-056EPS). shown in Figure 23. LINEAGE POWER 10 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc EN55022 Class B. For further information on designing for EMC Considerations EMC compliance, please refer to the FLT007A0 data sheet. The circuit and plots in Figure 24 shows a suggested configuration to meet the conducted emission limits of Level [dBµV] 80 70 60 x+ 50 x+ x+ 40 30 xxx 20 ++ + 10 0 150k 300k 500k 1M 2M 3M 4M5M 7M 10M 30M Frequency [Hz] x xMES CE0916111952_fin QP + +MES CE0916111952_fin AV MES CE0916111952_pre PK MES CE0916111952_pre AV Figure 24. EMC Considerations. Packaging Details All versions of the EBVW017A0S14R0 are supplied as Each tray contains a total of 18 power modules. The standard in the plastic trays shown in Figure 25. trays are self-stacking and each shipping box for the EBVW017A0S14R0 module contains 2 full trays plus Tray Specification one empty hold-down tray giving a total number of 36 power modules Material PET (1mm) 9 11 Max surface resistivity 10 -10 /PET Color Clear Capacity 18 power modules Min order quantity 36 pcs (1 box of 2 full trays + 1 empty top tray) Open Frame Module Tray Base Plate Module Tray Figure 25. EBVW020 Packaging Tray LINEAGE POWER 11 Data S Sheet EBVW017A0S14R0 S Series Pow wer Modules; DC-DC C Converters s April 11 1, 2013 36-75V IInput; 14.0V V Output t; 17A Outp put Current t dc dc Mecha anical Outline for EB BVW017A0S14R0 Through-ho ole Modulle Dimensio ons are in milliimeters and [in nches]. Tolerance es: x.x mm  0 0.5 mm [x.xx iin.  0.02 in.] ( (Unless otherw wise indicated d) x.xx mm  0.25 mm [x.x xxx in  0.010 in.] Top side la abel includes Lineage Powe er name, prod duct designatio on and date co ode. Top View* * Side View w *For optional pin lengths, see Table 2, Device Co oding Scheme and Options Bottom m View w                                                           Pin Fu unction   1 Vi(+)   2 ON/OFF   3 Vi(-)   4 Vo o(-) 8 Vo o(+)         LINEAG GE POWER 12 Data S Sheet EBVW017A0S14R0 S Series Pow wer Module es; DC-DC C Converters s April 11 1, 2013 36-75V IInput; 14.0V Output t; 17A Outp put Current t dc dc Mecha anical Outline for EB BVW017A0S14R0–H H (Basepla ate version) Throug gh-hole Module Dimensio ons are in milliimeters and [in nches]. Tolerance es: x.x mm  0 0.5 mm [x.xx iin.  0.02 in.] ( (Unless otherw wise indicated d) x.xx mm  0.25 mm [x.x xxx in  0.010 in.] Top Viiew Side e View w *For optio onal pin length hs, see Table 2, Device Cod ding Scheme and Options * Bottom side label includes Lineage e Power name e, product designation and d date Botto om View w*                                                            Pin Function 1 Vi(+)   2 ON/OFF   3 Vi(-)   4 Vo(-) 8 Vo(+)                        LINEAG GE POWER 13 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Recommended Pad Layouts Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm ( x.xx in.  0.02 in.) [unless otherwise indicated] x.xx mm  0.25 mm ( x.xxx in  0.010 in.) Through-Hole Modules Pin Pin Number Name 1* VIN(+) 2* ON/OFF 3* VIN(-) 4* VOUT(-) 8* VOUT(+) LINEAGE POWER 14 Data Sheet EBVW017A0S14R0 Series Power Modules; DC-DC Converters April 11, 2013 36-75V Input; 14.0V Output; 17A Output Current dc dc Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 1. Device Codes Output Output Connector Product codes Input Voltage Efficiency Comcodes Voltage Current Type EBVW017A0S14R0641Z 48V (3675Vdc) 14.0V 17A 95.5% Through hole 150022524 Table 2. Device Options Asia-Pacific Headquarters Tel: +86.021.54279977*808 Europe, Middle-East and Africa Headquarters World Wide Headquarters Tel: +49.89.878067-280 Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-888-LINEAGE(546-3243) (Outside U.S.A.: +1-972-244-WATT(9288)) India Headquarters Tel: +91.80.28411633 www.lineagepower.com e-mail: techsupport1@lineagepower.com Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. © 2010 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved.