Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to1.5Vdc output; 120A Output Current Features ▪ Compliant to RoHS EU Directive 2002/95/EC (Z versions) ▪ Compliant to IPC-9592 (September 2008), Category 2 ▪ Compatible in a Pb-free or SnPb reflow environment (Z versions) ▪ Compliant to REACH Directive (EC) No 1907/2006 ▪ Wide Input voltage range (7Vdc-14 Vdc) ▪ Output voltage programmable from 0.6Vdc to 1.5Vdc TM # via external resistor or PMBus commands ▪ Digital interface through the PMBus protocol ▪ Ability to parallel multiple modules (optional) ▪ Digital sequencing RoHS Compliant ▪ Fast digital loop control ▪ Power Good signal Applications ▪ Fixed switching frequency with capability of external ▪ Networking equipment synchronization ▪ Telecommunications equipment ▪ Output overcurrent protection (non-latching) ▪ Servers and storage applications ▪ Output overvoltage protection ▪ Over temperature protection ▪ Distributed power architectures ▪ Remote On/Off ▪ Intermediate bus voltage applications ▪ Ability to sink and source current ▪ Industrial equipment ▪ Cost efficient open frame design ▪ Small size: 53.8 x 31.7 x 13.3 mm [ 2.118” x 1.248” x 0.524”] ▪ Wide operating temperature range [-40°C to 85°C] nd † ▪ UL* 60950-1 2 Ed.+A1+A2 Recognized, CSA C22.2 ‡ No. 60950-1-07+A1+A2 Certified, and VDE (EN60950-1 nd 2 Ed.+A11+A1+A12+A2) Licensed ▪ ISO** 9001 and ISO 14001 certified manufacturing facilities Description TM The 120A Digital TeraDLynx power modules are non-isolated dc-dc converters that can deliver up to 120A of output current. These modules operate over a 7 to 14Vdc input range and provide a precisely regulated output voltage from 0.6 to 1.5Vdc. The output voltage is programmable via an external resistor and/or PMBus control. Features include a digital interface using the PMBus protocol, remote On/Off, adjustable output voltage, Power Good signal and overcurrent, overvoltage and overtemperature protection. The PMBus interface supports a range of commands to both control and monitor the module. The module also includes a real time compensation loop that allows optimizing the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards # The PMBus name and logo are registered trademarks of the System Management Interface Forum (SMIF) January 18, 2018 ©2017 General Electric Company. All rights reserved. Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are only absolute stress ratings, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the technical requirements. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage - Continuous All VIN -0.3 15 V SEQ, ADDR0, ADDR1, RTUNE, RTRIM, SYNC, VS+, ON/OFF All -0.3 3.6 V CLK, DATA, SMBALERT# All -0.3 3.6 V Operating Ambient Temperature All TA -40 85 °C (see Thermal Considerations section) Storage Temperature All Tstg -55 125 °C Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All V 7 14 Vdc IN  Maximum Input Current All I 29 Adc IN,max (VIN=7V to 14V, IO=IO, max ) VO,set = 0.6 Vdc IIN,No load 160 mA Input No Load Current (V = 12Vdc, I = 0, module enabled) IN O VO,set = 1.5Vdc IIN1No load 200 mA Input Stand-by Current All I 62 mA IN,stand-by (VIN = 12Vdc, module disabled) 2 2 Inrush Transient All I t 1 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN =0 to 14V, IO= All 5 mAp-p IOmax ; See Test Configurations) Input Ripple Rejection (120Hz) All -54 dB Output Voltage Set-point Tolerance over output voltage range from 0.5 to 1.5V 0 to 85ºC All V -0.7 +0.7 % V O, set O, set -40 to 85ºC All VO, set -1.0 +1.0 % VO, set 1 Voltage Regulation (VIN=VIN, min to VIN, max) 2 mV Line Regulation (12VIN±20%) 1 mV Load (IO=IO, min to IO, max) Regulation All 4 mV 1 Worst case Line and load regulation data, all temperatures, from design verification testing as per IPC9592. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 2 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Adjustment Range (selected by an external resistor) All VOUT 0.6 1.5 Vdc PMBus Adjustable Output Voltage Range All V 0.6 1.5 Vdc OUT 2 PMBus Output Voltage Adjustment Step Size All 61 µV Remote Sense Range All 0.3 Vdc Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 1500 μF Peak-to-Peak (Full bandwidth) 30 mV pk-pk RMS (Full bandwidth) All 12 mVrms 3 External Capacitance Minimum output capacitance All C 1500 μF O,min   Maximum output capacitance All CO, max   40000 μF Output Current (in either sink or source mode) All Io 0.005* 120 Adc Output Current Limit Inception (Hiccup Mode) All IO, lim 110 % Io,max (current limit does not operate in sink mode) Output Short-Circuit Current All IO1, s/c , IO1, s/c 40 Arms (VO≤250mV) (Hiccup Mode) Efficiency VO,set = 0.6Vdc η 88.2 % VO, set = 0.8Vdc η 90.9 % V = 12Vdc, T =25°C V = 1.0Vdc η 92.1 % IN A O,set IO=IO, max , VO= VO,set VO,set = 1.2Vdc η 93.0 % V = 1.5Vdc η 94.0 % O, set Switching Frequency All fsw - 400 - kHz Frequency Synchronization All Synchronization Frequency Range All -15 +15 % High-Level Input Voltage All V 2.5 V IH,SYNC Low-Level Input Voltage All V 1.1 V IL,SYNC Minimum Pulse Width, SYNC All tSYNC 256 ns * Minimum load on module should be 5mA 2 this must be supported by an appropriate PMBus tool capable of writing at that resolution 3 TM External capacitors may require using the new Tunable Loop feature to ensure that the module is stable as well as getting the best TM transient response. See the Tunable Loop section for details. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 3 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current General Specifications Parameter Device Min Typ Max Unit Calculated MTBF (I =0.8I , T =40°C) Telecordia Issue 2 Method 1 Case 3 All 11,556,226 Hours O O, max A Weight - Module with SMT Pins 57 (2.01) g (oz.) Module with Through Hole Pins 59 (2.08) g (oz.) Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit On/Off Signal Interface (V =V to V ; open collector or equivalent, IN IN, min IN, max Signal referenced to GND) Device Code with no suffix - Negative Logic (See Ordering Information) (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) Logic High (Module OFF) Input High Current All IIH ― ― 1 mA Input High Voltage All VIH 2 ― 3.6* Vdc Logic Low (Module ON) Input low Current All IIL ― ― 10 μA Input Low Voltage All VIL -0.2 ― 0.4 Vdc Device Code with suffix “4” - Positive Logic (See Ordering Information) (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) Logic High (Module ON) Input High Current All IIH ― ― 10 µA Input High Voltage All VIH 2 ― 3.6* Vdc Logic Low (Module OFF) Input low Current All IIL ― ― 10 μA Input Low Voltage All VIL -0.2 ― 0.4 Vdc Turn-On Delay and Rise Times (V =V , I =I V to within ±1% of steady state) IN IN, nom O O, max , O Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = All Tdelay ― 10 ― ms 10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at All Tdelay ― 2 ― ms which Von/Off is enabled until Vo = 10% of Vo, set) Output voltage Rise time (time for Vo to rise from All Trise ― 5 ― msec 10% of Vo, set to 90% of Vo, set) o Output voltage overshoot (TA = 25 C V = V to V ,I = I to I ) Output 3.0 % V IN IN, min IN, max O O, min O, max O, set With or without maximum external capacitance Over Temperature Protection All Tref 135 °C (See Thermal Considerations section) PMBus Over Temperature Warning Threshold All TWARN 125 °C *Use external resistive voltage divider to step down higher logic voltages January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 4 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Feature Specifications (cont.) Parameter Device Symbol Min Typ Max Units Tracking Accuracy (Power-Up: 0.5V/ms) All VSEQ –Vo 100 mV (Power-Down: 0.5V/ms) All VSEQ –Vo 100 mV (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) Input Undervoltage Lockout Turn-on Threshold All 7 Vdc Turn-off Threshold All 6.75 Vdc Hysteresis All 0.25 Vdc PMBus Adjustable Input Under Voltage Lockout Thresholds All 7 14 Vdc Resolution of Adjustable Input Under Voltage Threshold All 5.8 mV PGOOD (Power Good) Signal Interface Open Drain, V  5VDC supply Overvoltage threshold for PGOOD ON All 110 %VO, set Overvoltage threshold for PGOOD OFF All 110 %V O, set Undervoltage threshold for PGOOD ON All 90 %VO, set Undervoltage threshold for PGOOD OFF All 90 %VO, set Pulldown resistance of PGOOD pin All 2  Sink current capability into PGOOD pin All 50 mA January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 5 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 8Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Digital Interface Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Conditions Symbol Min Typ Max Unit PMBus Signal Interface Characteristics Input High Voltage (CLK, DATA) VIH 2.1 V Input Low Voltage (CLK, DATA) VIL 1.1 V Input high level current (CLK, DATA) IIH 0.5 μA Input low level current (CLK, DATA) IIL 4 mA Output Low Voltage (CLK, DATA, SMBALERT#) IOUT=4mA VOL 0.25 V Output high level open drain leakage current (DATA, VOUT=3.6V IOH 5 55 nA SMBALERT#) Pin capacitance CO 10 pF PMBus Operating frequency range Slave Mode FPMB 10 1000 kHz tHD:DAT Data hold time 0 ns tSU:DAT Data setup time 100 ns Measurement System Characteristics Read delay time tDLY 110 μs Output current measurement range I 0 135 A RNG Output current measurement resolution IRES 250 mA % of Output current measurement accuracy -40°C to +85°C I ±5 ACC Io,max V measurement range V 0 2.0 V OUT OUT % of VOUT measurement accuracy ±1 VOUT(gain) Vo,max VOUT measurement resolution 0.61 mV VOUT(res) V measurement range 0 16 V IN VIN VIN measurement accuracy V ±2 % IN(gain) V measurement resolution IN V 5.8 mV IN(res) Temperature measurement range T -25 150 °C MEAS Temperature measurement accuracy T -8 8 °C MEAS(gain) Temperature measurement resolution T 0.08 °C MEAS(res) January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 6 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Characteristic Curves TM o The following figures provide typical characteristics for the 120A Digital TeraDLynx at 0.6Vo and 25 C. 95 140 90 120 85 100 Vin=7V NC Vin=14V Vin=12V 0.5m/s 80 80 (100LFM) 75 60 70 40 0 20 40 60 80 100 120 25 35 45 55 65 75 85 O OUTPUT CURRENT, I (A) AMBIENT TEMPERATURE, T C O A Figure 1. Converter Efficiency versus Output Current. Figure 2. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (50s/div) TIME, t (200s /div) Figure 3. Typical output ripple and noise (C =12x47µF Figure 4. Transient Response to Dynamic Load Change from O ceramic + 10x470µF polymer, VIN = 12V, Io = Io,max,). 25% to 75% at 12Vin, Co= 12 x 47µF + 10 x 1000µF, RTUNE = 3.01kΩ. TIME, t (10ms/div) TIME, t (10ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = 12V, Io = Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max). Io,max). January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 7 OUTPUT VOLTAGE ON/OFFVOLTAGE OUTPUT VOLTAGE EFFICIENCY,  (%) VO (V) (200mV/div) VON/OFF (V) (5V/div) VO (V) (5mV/div) OUTPUT VOLTAGE INPUT VOLTAGE OUTPUT CURRENT, OUTPUT VOLTAGE OUTPUT CURRENT, Io (A) VO (V) (200mV/div) VIN (V) (10V/div) I (A) (50A/div) V (V) (20mV/div) O O Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Characteristic Curves TM o The following figures provide typical characteristics for the 120A TeraDLynx at 0.8Vo and 25 C 95 140 1m/s (200LFM) 120 90 100 Vin=7V Vin=12V Vin=14V 85 NC 80 0.5m/s (100LFM) 80 60 75 40 0 20 40 60 80 100 120 25 35 45 55 65 75 85 O OUTPUT CURRENT, I (A) AMBIENT TEMPERATURE, T C O A Figure 7. Converter Efficiency versus Output Current. Figure 8. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (50s/div) TIME, t (200s /div) Figure 9. Typical output ripple and noise (C =12x47µF Figure 10. Transient Response to Dynamic Load Change from O ceramic + 10x470µF polymer, VIN = 12V, Io = Io,max,) 25% to 75% at 12Vin, Co= 12 x 47µF + 10 x 1000µF, RTUNE = 3.01kΩ. TIME, t (10ms/div) TIME, t (10ms/div) Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 8 OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE EFFICIENCY,  (%) V (V) (200mV/div) V (V) (5V/div) V (V) (5mV/div) O ON/OFF O OUTPUT VOLTAGE INPUT VOLTAGE OUTPUT CURRENT OUTPUT VOLTAGE OUTPUT CURRENT, Io (A) VO (V) (200mV/div) VIN (V) (10V/div) IO (A) (50A/div) VO (V) (20mV/div) Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Characteristic Curves TM o The following figures provide typical characteristics for the 120A Digital TeraDLynx at 1.0Vo and 25 C. 95 140 1m/s (200LFM) 120 90 Vin=14V Vin=7V Vin=12V 100 85 NC 80 0.5m/s 80 (100LFM) 60 75 40 0 20 40 60 80 100 120 25 35 45 55 65 75 85 O OUTPUT CURRENT, IO (A) AMBIENT TEMPERATURE, TA C Figure 13. Converter Efficiency versus Output Current. Figure 14. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (50s/div) TIME, t (200s /div) Figure 15. Typical output ripple and noise (CO=12x47µF Figure 16. Transient Response to Dynamic Load Change from ceramic + 10x470µF polymer, VIN = 12V, Io = Io,max,) 25% to 75% at 12Vin, Co= 12 x 47µF + 10 x 1000µF, R = TUNE 3.01kΩ. TIME, t (10ms/div) TIME, t (10ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io = Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max). Io,max). January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 9 OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE EFFICIENCY,  (%) V (V) (300mV/div) V (V) (5V/div) VO (V) (5mV/div) O ON/OFF OUTPUT VOLTAGE INPUT VOLTAGE OUTPUT CURRENT, OUTPUT VOLTAGE OUTPUT CURRENT, Io (A) V (V) (300mV/div) V (V) (10V/div) O IN I (A) (50A/div) V (V) (20mV/div) O O Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Characteristic Curves TM o The following figures provide typical characteristics for the 120A Digital TeraDLynx at 1.2Vo and 25 C. 100 140 1m/s (200LFM) 120 95 100 90 NC Vin=7V Vin=12V Vin=14V 80 85 0.5m/s 60 (100LFM) 80 40 0 20 40 60 80 100 120 25 35 45 55 65 75 85 O OUTPUT CURRENT, IO (A) AMBIENT TEMPERATURE, TA C Figure 19. Converter Efficiency versus Output Current. Figure 20. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (50s/div) TIME, t (200s /div) Figure 21. Typical output ripple and noise (CO=12x47µF Figure 22. Transient Response to Dynamic Load Change from ceramic + 10x470µF polymer, VIN = 12V, Io = Io,max,) 25% to 75% at 12Vin, Co= 12 x 47µF + 10 x 1000µF, R = TUNE 3.01kΩ. TIME, t (2ms/div) TIME, t (10ms/div) Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 10 OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE EFFICIENCY,  (%) VO (V) (300mV/div) VON/OFF (V) (5V/div) VO (V) (5mV/div) OUTPUT VOLTAGE INPUT VOLTAGE OUTPUT CURRENT, OUTPUT VOLTAGE OUTPUT CURRENT, Io (A) VO (V) (300mV/div) VIN (V) (10V/div) I (A) (50A/div) V (V) (20mV/div) O O Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Characteristic Curves TM o The following figures provide typical characteristics for the 120A Digital TeraDLynx at 1.5Vo and 25 C. 100 140 1m/s (200LFM) 120 95 Vin=7V 100 90 Vin=14V Vin=12V 80 NC 85 0.5m/s 60 (100LFM) 80 40 0 20 40 60 80 100 120 25 35 45 55 65 75 85 O OUTPUT CURRENT, IO (A) AMBIENT TEMPERATURE, TA C Figure 25. Converter Efficiency versus Output Current. Figure 26. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (50s/div) TIME, t (200s /div) Figure 27. Typical output ripple and noise (CO=12x47µF Figure 28. Transient Response to Dynamic Load Change from ceramic + 10x470µF polymer, VIN = 12V, Io = Io,max,) 25% to 75% at 12Vin, Co= 12 x 47µF + 10 x 1000µF, R = TUNE 3.01kΩ. TIME, t (2ms/div) TIME, t (2ms/div) Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 11 OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE EFFICIENCY,  (%) VO (V) (500mV/div) VON/OFF (V) (5V/div) VO (V) (5mV/div) OUTPUT VOLTAGE INPUT VOLTAGE OUTPUT CURRENT, OUTPUT VOLTAGE OUTPUT CURRENT, Io (A) VO (V) (500mV/div) VIN (V) (5V/div) I (A) (50A/div) V (V) (20mV/div) O O Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current performance of the module can be achieved by using the Design Considerations TM Tunable Loop feature described later in this data sheet. Input Filtering 10 TM The 120A TeraDLynx module should be connected to a 10x470 + 12x47 +12x10 uF low ac-impedance source. A highly inductive source can 4x470 + 12x47 +12x10 uF 8 affect the stability of the module. An input capacitance must be placed directly adjacent to the input pins of the module, to minimize input ripple voltage and ensure 6 module stability. To minimize input voltage ripple, ceramic capacitors are recommended at the input of the module. Figure 31 4 shows the input ripple voltage for various output voltages at 120A of load current with 4x470 + 12x22 + 12x4.7 µF and 2x470 + 6x22 + 12x4.7 µF input capacitor 2 combinations. 25 0 4x470 + 12x22 + 12x4.7 uF 0.5 0.7 0.9 1.1 1.3 1.5 2x470 + 6x22 + 12x4.7 uF Output Voltage(Volts) 20 Figure 32. Peak to peak output ripple voltage for various output voltages with external capacitors at the output (120A load). Input voltage is 12V. 15 Safety Considerations For safety agency approval the power module must be 10 installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., nd ANSI/UL 60950-1 2 Revised October 14, 2014, CSA C22.2 5 No. 60950-1-07, Second Ed. + A2:2014 (MOD), DIN EN 60950- 0.5 0.7 0.9 1.1 1.3 1.5 1:2006 + A11:2009 + A1:2010 +A12:2011, + A2:2013 (VDE0805 Teil 1: 2014-08)(pending). Output Voltage(Volts) For the converter output to be considered meeting the Figure 31. Input ripple voltage for various output requirements of safety extra-low voltage (SELV), the input voltages with two input capacitor combinations at must meet SELV requirements. The power module has 120A load. Input voltage is 12V. extra-low voltage (ELV) outputs when all inputs are ELV. Output Filtering The input to these units is to be provided with a slow-blow fuse. When the input voltage is ≤ 8V, the recommendation is These modules are designed for low output ripple voltage to use two 25A Littelfuse 456 series or equivalent fuses in and will meet the maximum output ripple specification with parallel. For input voltages > 8V, a single 40A Littelfuse series minimum of 12 x 22 µF ceramic capacitors at the output of 456 or equivalent fuse is recommended. the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. Figure 32 provides output ripple information for capacitance of ~3574uF (47µF (1210 ceramic) x 12 + 10µF (0805 ceramic) + 0.1µF (0402) x4 + 1000µF (polymer) x 3) at various Vo and a full load current of 120A. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. Optimal January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 12 Ripple (mVp-p) Ripple (mVp-p) Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current The trim resistor is only determined during module Analog Feature Descriptions initialization and hence cannot be used for dynamic output Remote On/Off voltage adjustment The TeraDLynx 120A module can be turned ON and OFF either by using the ON/OFF pin (Analog interface) or through RTRIM the PMBus interface (Digital). The module can be configured in a number of ways through the PMBus interface to react to R the ON/OFF input: TRIM • Module ON/OFF can controlled only through the analog interface (digital interface ON/OFF SIG_GND commands are ignored) • Module ON/OFF can controlled only through the PMBus interface (analog interface is ignored) Figure 33. Circuit configuration for programming output • Module ON/OFF can be controlled by either the voltage using an external resistor. analog or digital interface Table 1 The default state of the module (as shipped from the factory) is to be controlled by the analog interface only. If the digital VO, set Rtrim VO, set Rtrim VO, set Rtrim interface is to be enabled, or the module is to be controlled (V) (Ω) (V) (Ω) (V) (Ω) only through the digital interface, this change must be made 0.600 1090 1.000 2870 1.400 18900 through the PMBus. These changes can be made and 0.620 1140 1.020 3050 1.420 23200 written to non-volatile memory on the module so that it is 0.640 1180 1.040 3240 1.440 29800 remembered for subsequent use. 0.660 1230 1.060 3480 1.460 40200 Analog On/Off 0.680 1290 1.080 3700 1.480 60400 TM The 120A Digital TeraDLynx power modules feature an 0.700 1330 1.100 3920 1.500 115000 On/Off pin for remote On/Off operation. With the Negative 0.720 1380 1.120 4220 Logic On/Off option, (see Ordering Information), the module turns OFF during logic High and ON during logic Low. The 0.740 1470 1.140 4530 On/Off signal should be always referenced to ground. 0.760 1560 1.160 4990 Leaving the On/Off pin disconnected will turn the module 0.780 1640 1.180 5360 ON when input voltage is present. With the positive logic 0.800 1740 1.200 5900 on/off option, the module turns ON during logic high and OFF during logic low. 0.820 1820 1.220 6420 0.840 1930 1.240 6980 Digital On/Off 0.860 2030 1.260 7680 Please see the Digital Feature Descriptions section. 0.880 2130 1.280 8450 Monotonic Start-up and Shutdown 0.900 2230 1.300 9420 The module has monotonic start-up and shutdown behavior 0.920 2340 1.320 10400 on the output for any combination of rated input voltage, 0.940 2460 1.340 11700 output current and operating temperature range. 0.960 2610 1.360 13500 Startup into Pre-biased Output 0.980 2710 1.380 15800 The module will start into a pre biased output on output as long as the pre bias voltage is 0.5V less than the set output Digital Output Voltage Adjustment voltage. Please see the Digital Feature Descriptions section. Analog Output Voltage Programming Remote Sense The output voltage of the module is programmable to any The power module has a differential Remote Sense feature voltage from 0.6 to 1.5Vdc, as shown in Table 1, by to minimize the effects of distribution losses by regulating connecting a resistor between the Trim and SIG_GND pins of the voltage between the sense pins (VS+ and VS-) for the the module as shown in Fig 33. output. The voltage drop between the sense pins and the VOUT and GND pins of the module should not exceed 0.3V. Without an external resistor between the Trim pin and SIG_GND pins, the output of the module will be 0.1 Vdc. The Digital Output Voltage Margining value of the trim resistor, RTrim for a desired output voltage, should be selected as shown in Table 1. Please see the Digital Feature Descriptions section. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 13 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current To provide protection in a fault condition, the unit is Output Voltage Sequencing equipped with a thermal shutdown circuit. The unit will shut The power module includes a sequencing feature, EZ- down if the overtemperature threshold of 135 °C (typ) is SEQUENCE that enables users to implement various types of exceeded at the thermal reference point Tref. Once the unit output voltage sequencing in their applications. This is goes into thermal shutdown it will then wait to cool before accomplished via an additional sequencing pin. When not attempting to restart. using the sequencing feature, leave it unconnected. Digital Adjustable Overcurrent Warning/Shutdown Module Please see the Digital Feature Descriptions section. Digital Temperature Status via PMBus Please see the Digital Feature Descriptions section. V Digitally Adjustable Output Over and Under Voltage SEQ SEQ Protection Please see the Digital Feature Descriptions section. SIG_GND Input Undervoltage Lockout SIG_GND At input voltages below the input undervoltage lockout limit, Figure 34. Circuit showing connection of the sequencing module operation for the associated output is disabled. The signal to the SEQ pin. module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. When the sequencing voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches Digitally Adjustable Input Undervoltage Lockout the set-point voltage. The final value of the sequencing Please see the Digital Feature Descriptions section. voltage must be set higher than the set-point voltage of the module. The output voltage follows the sequencing voltage Digitally Adjustable Power Good Thresholds on a one-to-one basis. By connecting multiple modules together, multiple modules can track their output voltages Please see the Digital Feature Descriptions section. to the voltage applied on the SEQ pin. Synchronization The module’s output can track the SEQ pin signal with The module switching frequency is capable of being slopes of up to 0.5V/msec during power-up or power-down. synchronized to an external signal frequency within a To initiate simultaneous shutdown of the modules, the SEQ specified range. Synchronization is done by using the pin voltage is lowered in a controlled manner. The output external signal applied to the SYNC pin of the module as voltage of the modules tracks the voltages below their set- shown in Fig. 35, with the converter being synchronized by point voltages on a one-to-one basis. A valid input voltage the rising edge of the external signal. The Electrical must be maintained until the tracking and output voltages Specifications table specifies the requirements of the reach ground potential. external SYNC signal. If the SYNC pin is not used, the module should free run at the default switching frequency. Digital Sequencing The module can support digital sequencing by allowing MODULE control of the turn-on delay and rise times as well as turn- off and fall times, SYNC Digital Output Voltage Margining + Please see the Digital Feature Descriptions section. ─ Overcurrent Protection (OCP) SIG_GND To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry on output and can endure current limiting continuously. The Figure 35. External source connections to synchronize module overcurrent response is non-latching shutdown with switching frequency of the module. automatic recovery. OCP response time is programmable through manufacturer specific commands. The unit Measuring Output Current, Output Voltage and operates normally once the output current is brought back Input Voltage into its specified range. Please see the Digital Feature Descriptions section. Digital Adjustable Overcurrent Warning Digital Compensator Please see the Digital Feature Descriptions section. The TJT120 module uses digital control to regulate the Overtemperature Protection output voltage. As with all POL modules, external capacitors January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 14 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current are usually added to the output of the module for two capacitors. The range of external output capacitance is reasons: to reduce output ripple and noise and to reduce from 1470 µF to a maximum value of 17640 µF) output voltage deviations from the steady-state value in the • COMP2: For the most commonly used mix of ceramic presence of dynamic load current changes. Adding external and polymer type capacitors that have higher output capacitance however affects the voltage control loop of the capacitance in a smaller size. The range of output module, typically causing the loop to slow down with capacitance is from 2564 µF to a maximum of 30564 uF. sluggish response. Larger values of external capacitance could also cause the module to become unstable. This is the combination of output capacitance and compensation that can achieve the best transient The TJT120 comes with default compensation values response at lowest cost and smallest size. For example, programmed into the non-volatile memory of the module. with the maximum output capacitance of 12 x 47µF These digital compensation values can be adjusted externally to optimize transient response and also ensure ceramics + 25 x 1000 µF polymer capacitors, and stability for a wide range of external capacitance, as well as selecting RTUNE = 5.36kΩ, transient deviation can be as with different types of output capacitance. This can be done low as 25 mV, for a 50% load step (0 to 85A). by two different methods. • COMP3: Suitable for a mix of ceramic and higher ESR 1. By allowing the user to select among several pre-tuned polymers or electrolytic capacitors, with output compensation choices to select the one most suited to capacitance ranging from a minimum of 2204 µF to a the transient response needs of the load. This selection is maximum of 30084 µF. made via a resistor RTune connected between the Selecting R according to Table 2 will ensure stable TUNE RTUNE and SIG_GND pins as shown in Fig. 35. Table 2 operation of the module with sufficient stability margin as shows various pre-tuned compensation combinations well as yield optimal transient response. recommended for various external capacitor combinations. In applications with tight output voltage limits in the presence 2. Using PMBus to change compensation parameters in the of dynamic current loading, additional output capacitance module. will be required. Table 3 lists recommended values of R in TUNE Note that during initial startup of the module, compensation order to meet 2% output voltage deviation limits for some values that are stored in non-volatile memory are used. If a common output voltages in the presence of an 60A to 120A resistor RTune is connected to the module, then the step change (50% of full load), with an input voltage of 12V. compensation values are changed to ones that correspond Please contact your GE technical representative to obtain to the value of RTUNE. If RTUNE is open however, no change more details of this feature as well as for guidelines on how in compensation values is made. Finally, if the user chooses to select the right value of external RTUNE to tune the module to do so, they can overwrite the compensation values via for best transient performance and stable operation for other PMBus commands. output capacitance values. Simulation models are also Recommended values of R for different output capacitor TUNE available via the GE Power Module Wizard to predict stability combinations are given in Table 2. If no RTUNE is used, the characteristics and transient response. default compensation values are used. The TJT120 pre-tuned compensation can be divided into RTUNE three different banks (COMP1, COMP2, COMP3) that are available to the user to compensate the control loop for various values and combinations of output capacitance and R to obtain reliable and stable performance under different TUNE conditions. Each bank consists of 20 different sets of compensation coefficients pre-calculated for different values of output capacitance. The three banks are set up as SIG_GND follows: • COMP1: Recommended for the case where all of the Figure 36. Circuit diagram showing connection of R to TUNE output capacitance is composed of only ceramic tune the control loop of the module. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 15 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 2. Recommended RTUNE Compensation. Output Number of Output Total Output RTUNE RTUNE KD KI KP AP Capacitance Type Capacitors** Capacitance (µF)** resistor (Ω) Index Default Compensation Values OPEN 375 2 37 150 Ceramic 10 x 47µF + 10 x 100µF 1398 29.1 0 375 2 37 150 Ceramic 12 x 47µF + 12 x 100µF 1644 88.7 1 441 3 44 150 Ceramic 14 x 47µF + 14 x 100µF 1890 150 2 506 3 51 150 Ceramic 16 x 47µF + 16 x 100µF 2136 213 3 572 3 57 150 Ceramic 19 x 47µF + 19 x 100µF 2505 280 4 671 3 67 150 Ceramic 22 x 47µF + 22 x 100µF 2874 348 5 770 4 77 150 Ceramic 25 x 47µF + 25 x 100µF 3243 417 6 869 4 87 150 7 Ceramic 28 x 47µF + 28 x 100µF 3612 493 968 4 97 150 Ceramic 31 x 47µF + 31 x 100µF 3981 569 8 1067 4 107 150 Ceramic 34 x 47µF + 34 x 100µF 4350 642 9 1166 4 117 150 10 Ceramic 38 x 47µF + 38 x 100µF 4842 723 1297 5 130 150 Ceramic 42 x 47µF + 42 x 100µF 5334 806 11 1429 5 143 150 Ceramic 48 x 47µF + 48 x 100µF 6072 898 12 1627 5 163 150 13 Ceramic 55 x 47µF + 55 x 100µF 6933 938 1858 5 186 150 Ceramic 63 x 47µF + 63 x 100µF 7917 1090 14 2121 6 212 150 Ceramic 72 x 47µF + 72 x 100µF 9024 1180 15 2418 6 242 150 16 Ceramic 82 x 47µF + 82 x 100µF 10254 1290 2748 7 275 150 Ceramic 93 x 47µF + 93 x 100µF 11607 1400 17 3110 7 311 150 Ceramic 105 x 47µF + 105 x 100µF 13083 1520 18 3506 7 351 150 19 Ceramic 120 x 47µF + 120 x 100µF 14928 1640 4000 8 400 150 20 Ceramic + Polymer 12 x 47µF + 2 x 1000µF 2672 1760 501 3 300 220 21 Ceramic + Polymer 12 x 47µF + 3 x 1000µF 3672 1890 688 3 413 220 22 Ceramic + Polymer 12 x 47µF + 4 x 1000µF 4672 2030 876 3 525 220 23 Ceramic + Polymer 12 x 47µF + 5 x 1000µF 5672 2150 1063 4 638 220 24 Ceramic + Polymer 12 x 47µF + 6 x 1000µF 6672 2320 1250 4 750 220 25 Ceramic + Polymer 12 x 47µF + 7 x 1000µF 7672 2460 1438 4 860 220 26 Ceramic + Polymer 12 x 47µF + 8 x 1000µF 8672 2640 1625 5 975 220 27 Ceramic + Polymer 12 x 47µF + 9 x 1000µF 9672 2840 1813 5 1088 220 28 Ceramic + Polymer 12 x 47µF + 10 x 1000µF 10672 3010 2000 5 1200 220 29 Ceramic + Polymer 12 x 47µF + 11 x 1000µF 11672 3200 2187 5 1312 220 30 Ceramic + Polymer 12 x 47µF + 12 x 1000µF 12672 3400 2375 5 1425 220 31 Ceramic + Polymer 12 x 47µF + 13 x 1000µF 13672 3650 2562 6 1537 220 32 Ceramic + Polymer 12 x 47µF + 15 x 1000µF 15672 3880 2937 6 1762 220 33 Ceramic + Polymer 12 x 47µF + 17 x 1000µF 17672 4120 3312 6 1987 220 34 Ceramic + Polymer 12 x 47µF + 19 x 1000µF 19672 4420 3687 7 2212 220 35 Ceramic + Polymer 12 x 47µF + 21 x 1000µF 21672 4700 4061 7 2437 220 36 Ceramic + Polymer 12 x 47µF + 23 x 1000µF 23672 5050 4436 7 2662 220 37 Ceramic + Polymer 12 x 47µF + 25 x 1000µF 25672 5360 4811 8 2887 220 38 Ceramic + Polymer 12 x 47µF + 27 x 1000µF 27672 5760 5186 8 3112 220 39 Ceramic + Polymer 12 x 47µF + 30 x 1000µF 30672 6120 5748 8 3449 220 ** Total output capacitance includes the capacitance inside the module is 4 x 47µF (3mΩ ESR). Note: The capacitors used in the digital compensation Loop tables are 47μF/3 mΩ ESR ceramic, 100uF/3.2mΩ ceramic, 1000 μF/6mΩ ESR polymer capacitor and 820uF/19mΩ ESR Polymer capacitor. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 16 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 2 (continued). R compensation table TUNE Output Capacitance Number of Output Total Output R resistor R TUNE TUNE KD KI KP AP Type Capacitors** Capacitance (µF)** (Ω) Index Ceramic + Electrolytic 12 x 47µF + 2 x 820µF 2312 6570 40 176 2 176 220 Ceramic + Electrolytic 12 x 47µF + 3 x 820µF 3312 7060 41 238 3 238 220 Ceramic + Electrolytic 12 x 47µF + 4 x 820µF 3952 7590 42 301 3 301 220 Ceramic + Electrolytic 12 x 47µF + 5 x 820µF 4772 8160 43 363 3 363 220 Ceramic + Electrolytic 12 x 47µF + 6 x 820µF 5592 8870 44 426 4 426 220 Ceramic + Electrolytic 12 x 47µF + 7 x 820µF 6412 9530 45 488 4 488 220 Ceramic + Electrolytic 12 x 47µF + 8 x 820µF 7312 10400 46 550 4 550 220 Ceramic + Electrolytic 12 x 47µF + 9 x 820µF 8052 11300 47 613 4 613 220 Ceramic + Electrolytic 12 x 47µF + 10 x 820µF 8872 12400 48 675 5 675 220 Ceramic + Electrolytic 12 x 47µF + 11 x 820µF 9692 13700 49 738 5 738 220 Ceramic + Electrolytic 12 x 47µF + 12 x 820µF 10512 15000 50 800 5 800 220 Ceramic + Electrolytic 12 x 47µF + 14 x 820µF 12152 16700 51 925 5 925 220 Ceramic + Electrolytic 12 x 47µF + 16 x 820µF 13792 18700 52 1050 6 1050 220 Ceramic + Electrolytic 12 x 47µF + 18 x 820µF 15432 21000 53 1174 6 1174 220 Ceramic + Electrolytic 12 x 47µF + 20 x 820µF 17072 24000 54 1299 6 1299 220 Ceramic + Electrolytic 12 x 47µF + 23 x 820µF 19532 28000 55 1486 7 1486 220 Ceramic + Electrolytic 12 x 47µF + 26 x 820µF 21992 33000 56 1674 7 1674 220 Ceramic + Electrolytic 12 x 47µF + 29 x 820µF 24452 40200 57 1861 8 1861 220 Ceramic + Electrolytic 12 x 47µF + 32 x 820µF 26912 50500 58 2048 8 2048 220 Ceramic + Electrolytic 12 x 47µF + 36 x 820µF 30192 68000 59 2298 8 2298 220 ** Total output capacitance includes the capacitance inside the module is 4 x 47µF (3mΩ ESR). Note: The capacitors used in the digital compensation Loop tables are 47μF/3 mΩ ESR ceramic, 100uF/3.2mΩ ceramic, 1000 μF/6mΩ ESR polymer capacitor and 820uF/19mΩ ESR Electrolytic capacitor. Power Module Wizard GE offers a free web based easy to use tool that helps users simulate the Tunable Loop performance of the TJT170. Go to http://ge.transim.com/pmd/Home and sign up for a free account and use the module selector tool. The tool also offers downloadable Simplis/Simetrix models that can be used to assess transient performance, module stability, etc. Bin ‘a’ and Bin ‘b’ settings using the models available through Power Module Wizard The TJT170 module has a built-in non-linear compensation adjustment to speed up its transient response to dynamic loading conditions. When the module senses a load transition in progress, it automatically adjusts the KD, KI, KP settings to higher values and then reverts to the values set before the transient conditions. The adjustment of the PID coefficients is as follows: Steady State Transient Condition Bin ‘a’ – User set values based on RTUNE or programmed Bin ‘b’ – Controller adjusted values for duration of transient KD KI KP KD KI KP A B X 2 x A 2 x B 2 x C For determining the voltage response to a current load transient, it is more accurate to use the Bin ‘b’ settings corresponding to the selected KD, KI, KP values. For Loop Stability Simulations, the selected PID values corresponding to Bin ‘a’ should be used. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 17 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current The value is of the number is then given by Digital Feature Descriptions Exponent Value = Mantissa x 2 PMBus Interface Capability PMBus Addressing The 120A TeraDLynx power modules have a PMBus The power module is addressed through the PMBus using a interface that supports both communication and control. device address. The module supports 128 possible The PMBus Power Management Protocol Specification can addresses (0 to 127 in decimal) which can be set using be obtained from www.pmbus.org. The modules support a resistors connected from the ADDR0 and ADDR1 pins to subset of version 1.1 of the specification (see Table 4 for a SIG_GND. Note that some of these addresses (0, 1, 2, 3, 4, 5, list of the specific commands supported). Most module 6, 7, 8, 9, 10, 11 12, 40, 44, 45, 55 in decimal) are reserved parameters can be programmed using PMBus and stored as according to the SMBus specification and may not be defaults for later use. useable. The address is set in the form of two octal (0 to 7) Communication over the module PMBus interface supports digits, with each pin setting one digit. The ADDR1 pin sets the Packet Error Checking (PEC) scheme. The PMBus master the high order digit and ADDR0 sets the low order digit. The must generate the correct PEC byte for all transactions, and resistor values suggested for each digit are shown in Table 3 check the PEC byte returned by the module. (E96 series resistors are recommended). Note that if either The module also supports the SMBALERT# response address resistor value is outside the range specified in Table protocol whereby the module can alert the bus master if it 4, the module will respond to address 127. wants to talk. For more information on the SMBus alert 2 The user must know which I C addresses are reserved in a response protocol, see the System Management Bus system for special functions and set the address of the (SMBus) specification. module to avoid interfering with other system operations. The module has non-volatile memory that is used to store Both 100kHz and 400kHz bus speeds are supported by the configuration settings. Not all settings programmed into the module. Connection for the PMBus interface should follow device are automatically saved into this non-volatile the High Power DC specifications given in section 3.1.3 in the memory, only those specifically identified as capable of SMBus specification V2.0 for the 400kHz bus speed or the being stored can be saved (see Table 4 for which command Low Power DC specifications in section 3.1.2. The complete parameters can be saved to non-volatile storage). SMBus specification is available from the SMBus web site, PMBus Data Format smbus.org. For commands that set thresholds, voltages or report such quantities, the module supports the “Linear” data format ADDR1 among the three data formats supported by PMBus. The Linear Data Format is a two-byte value with an 11-bit, two’s ADDR0 complement mantissa and a 5-bit, two’s complement exponent. The format of the two data bytes is shown below: R R ADDR0 ADDR1 Data Byte High Data Byte Low SIG_GND 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Figure 37. Circuit showing connection of resistors used to Exponent Mantissa set the PMBus address of the module. MSB MSB Table 3 PMBus Address Table ADDR1 Resistor Values ADDR0 Resistor 4.99K 15.4k 27.4K 41.2K 54.9K 71.5K 90.9K 110K 137K 162K 191K Values 4.99K 1 13 25 37 49 61 73 85 97 109 121 15.4K 2 14 26 38 50 62 74 86 98 110 122 27.4K 3 15 27 39 51 63 75 87 99 111 123 41.2K 4 16 28 40 52 64 76 88 100 112 124 54.9K 5 17 29 41 53 65 77 89 101 113 125 71.5K 6 18 30 42 54 66 78 90 102 114 126 90.9K 7 19 31 43 55 67 79 91 103 115 127 110K 8 20 32 44 56 68 80 92 104 116 64 137K 9 21 33 45 57 69 81 93 105 117 64 162K 10 22 34 46 58 70 82 94 106 118 64 191K 11 23 35 47 59 71 83 95 107 119 64 232K 12 24 36 48 60 72 84 96 108 120 64 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 18 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current CPA: Sets the action of the analog ON/OFF pin when turning Operation (01h) the controller OFF. This bit is internally read and cannot be This is a paged register. The OPERATION command can be modified by the user used to turn the module on or off in conjunction with the ON/OFF pin input. It is also used to margin up or margin PMBus Adjustable Soft Start Rise Time down the output voltage The soft start rise time of module output is adjustable in the module via PMBus. The TON_RISE command can set the rise PMBus Enabled On/Off time in ms, and allows choosing soft start times between 1 The module can also be turned on and off via the PMBus and 1000ms. interface. The OPERATION command is used to actually turn the module on and off via the PMBus, while the Output Voltage Adjustment Using the PMBus ON_OFF_CONFIG command configures the combination of Two PMBus commands are available to change the output analog ON/OFF pin input and PMBus commands needed to voltage setting. The first, VOUT_COMMAND can set the turn the module on and off. Bit [7] in the OPERATION output voltage directly. The second, VOUT_TRIM is used to command data byte enables the module, with the following apply an offset to the commanded output voltage. functions: Since the output voltage can be set using an external RTrim 0 : Output is disabled resistor as well, an additional PMBus command 1 : Output is enabled MFR_VOUT_SET_MODE is used to tell the module whether This module uses the lower five bits of the ON_OFF_CONFIG the VOUT_COMMAND is used to directly set output voltage or whether RTrim is to be used. If MFR_VOUT_SET_MODE is data byte to set various ON/OFF options as follows: set to where bit position 7 is set at 1, then VOUT_COMMAND Bit Position 4 3 2 1 0 is ignored and output voltage is set solely by RTrim. If bit 7 of Access r/w r/w r/w r r MFR_VOUT_SET_MODE is set to 0, then output voltage is set Function PU CMD CPR X CPA using VOUT_COMMAND, and the value of RTrim is only used Default Value 1 0 1 x 1 at startup to set the output voltage. The second output voltage adjustment command PU: Sets the default to either operate any time input power VOUT_TRIM works in either case to provide a fixed offset to is present or for the ON/OFF to be controlled by the analog the output voltage. This allows PMBus adjustment of the ON/OFF input and the PMBus OPERATION command. This bit output voltage irrespective of how MFR_VOUT_SET_MODE is is used together with the CP, CMD and ON bits to determine set and allows digital adjustment of the output voltage startup. setting even when RTrim is used. Bit Value Action For all digital commands used to set or adjust the output Module powers up any time power is voltage via PMBus, the resolution is 98µV. 0 present regardless of state of the analog Output Voltage Margining Using the PMBus ON/OFF pin Module does not power up until The output voltage of the module can be margined via commanded by the analog ON/OFF pin and PMBus between 0.6 and 1.5V. The margining voltage can be 1 the OPERATION command as programmed adjusted in 98µV steps. in bits [2:0] of the ON_OFF_CONFIG register. PMBus Adjustable Overcurrent Warning The module can provide an overcurrent warning via the CMD: The CMD bit controls how the device responds to the PMBus. The threshold for the overcurrent warning can be OPERATION command. set using the parameter IOUT_OC_WARN_LIMIT. This Bit Value Action command uses the “Linear” data format with a two byte Module ignores the ON bit in the data word where the upper five bits [7:3] of the high byte 0 OPERATION command represent the exponent and the remaining three bits of the Module responds to the ON bit in the high byte [2:0] and the eight bits in the low byte represent 1 the mantissa. The value of the IOUT_OC_WARN_LIMIT can OPERATION command be stored to non-volatile memory using the STORE_DEFAULT_ALL command. CPR: Sets the response of the analog ON/OFF pin. This bit is used together with the CMD, PU and ON bits to determine Temperature Status via PMBus startup. The module provides information related to temperature of the module through standardized PMBus commands. Bit Value Action Commands READ_TEMPERATURE1, READ_TEMPERATURE_2 Module ignores the analog ON/OFF pin, i.e. are mapped to module temperature and internal 0 ON/OFF is only controlled through the temperature of the PWM controller, respectively. The PMBUS via the OPERATION command temperature readings are returned in °C and in two bytes. Module requires the analog ON/OFF pin to 1 be asserted to start the unit January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 19 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current The module supports a number of status information PMBus Adjustable Output Over, Under Voltage commands implemented in PMBus. A 1 in the bit position Protection indicates the fault that is flagged. The module has output over and under voltage protection capability. The PMBus command VOUT_OV_FAULT_LIMIT is STATUS_BYTE: Returns one byte of information with a used to set the output over voltage threshold. The default summary of the most critical device faults. value is configured to be 112.5% of the commanded output. Bit Default The command VOUT_UV_FAULT_LIMIT sets the threshold Flag Position Value that detects an output under voltage fault. The default 7 X 0 values are 87.5% of the commanded output voltage. Both 6 OFF 0 commands use two data bytes formatted in the Linear 5 VOUT Overvoltage 0 format. 4 IOUT Overcurrent 0 PMBus Adjustable Input Undervoltage Lockout 3 VIN Undervoltage 0 2 Temperature 0 The module allows adjustment of the input under voltage 1 CML (Comm. Memory Fault) 0 lockout and hysteresis. The command VIN_ON allows setting 0 None of the above 0 the input voltage turn on threshold, while the VIN_OFF command sets the input voltage turn off threshold. For the STATUS_WORD: Returns two bytes of information with a VIN_ON command possible values are 7 to 14V and for the summary of the module’s fault/warning conditions. VIN_OFF command, possible values are 6.75V to 14V. Both Low Byte VIN_ON and VIN_OFF commands use the “Linear” format Bit Default with two data bytes. Flag Position Value Measurement of Output Current, Output Voltage 7 X 0 and Input Voltage 6 OFF 0 5 VOUT Overvoltage 0 The module can measure key module parameters such as 4 IOUT Overcurrent 0 output current, output voltage and input voltage and 3 VIN Undervoltage 0 provide this information through the PMBus interface. 2 Temperature 0 Measuring Output Current Using the PMBus 1 CML (Comm. Memory Fault) 0 0 None of the above 0 The module measures output current by using a signal derived from the switching FET currents. The current gain factor is accessed using the IOUT_CAL_GAIN command, and High Byte consists of two bytes in the Linear data format. During Bit Default Flag manufacture, each module is calibrated by measuring and Position Value storing the current gain factor into non-volatile storage. 7 VOUT fault or warning 0 6 IOUT fault or warning 0 The current measurement accuracy is also improved by 5 X 0 each module being calibrated during manufacture with the 4 X 0 offset in the current reading. The IOUT_CAL_OFFSET 3 POWER_GOOD# (is negated) 0 command is used to store and read the current offset. The 2 X 0 READ_IOUT command provides module average output 1 X 0 current information. This command only supports positive 0 X 0 output current, i.e. current sourced from the module. If the converter is sinking current a reading of 0 is provided. The STATUS_VOUT: Returns one byte of information relating to READ_IOUT command returns two bytes of data in the the status of the module’s output voltage related faults. Linear data format. Bit Default Measuring Output Voltage Using the PMBus Flag Position Value The module provides output voltage information using the 7 VOUT OV Fault 0 READ_VOUT command. The command returns two bytes of 6 VOUT_OV_WARNING 0 data in Linear format. 5 VOUT_UV_WARNING 0 4 VOUT UV Fault 0 Measuring Input Voltage Using the PMBus 3 X 0 The module provides input voltage information using the 2 X 0 READ_VIN command. The command returns two bytes of 1 X 0 data in the Linear format. 0 X 0 Reading the Status of the Module using the PMBus STATUS_IOUT: Returns one byte of information relating to the status of the module’s output voltage related faults. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 20 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Bit Default Flag Bit Default Position Value Flag Position Value 7:3 Module Revision Number None 7 IOUT OC Fault 0 2:0 Reserved 000 6 X 0 5 IOUT OC Warning 0 User-Programmable Compensation Coefficients 4 X 0 3 X 0 The output voltage control compensation coefficients can 2 X 0 be changed by the user via PMBus commands. On startup, 1 X 0 the module uses stored values of the four compensation 0 X 0 parameters KD, KI, KP and ALPHA. If the module detects a valid value of RTUNE connected to the module, the values of STATUS_TEMPERATURE: Returns one byte of information KD, KI, KP and ALPHA are then changed to the appropriate relating to the status of the module’s temperature related values. Beyond this, the user can use the PMBus commands faults. listed below to overwrite the values of KD, KP, KI and ALPHA. Bit Default MFR_SPECIFIC_KP: Allows the user to program the value of Flag Position Value the KP compensation coefficient. The allowed range is - 7 OT Fault 0 10922 to 10922. The entire 16 bits are used to enter this 6 OT Warning 0 range of integer values in two’s complement binary format. 5 X 0 For stable operation, use positive values only as suggested 4 X 0 with the maximum allowed value being 10922. 3 X 0 2 X 0 MFR_SPECIFIC_KI: Allows the user to program the value of 1 X 0 the KI compensation coefficient. The allowed range is - 0 X 0 10922 to 10922. The entire 16 bits are used to enter this range of integer values in two’s complement binary format. STATUS_CML: Returns one byte of information relating to the For stable operation, use positive values only as suggested status of the module’s communication related faults. with the maximum allowed value being 10922. Bit Default MFR_SPECIFIC_KD: Allows the user to program the value of Flag Position Value the KD compensation coefficient. The allowed range is - 7 Invalid/Unsupported Command 0 10922 to 10922. The entire 16 bits are used to enter this 6 Invalid/Unsupported Data 0 range of integer values in two’s complement binary format. 5 Packet Error Check Failed 0 For stable operation, use positive values only as suggested 4 Memory Fault Detected 0 with the maximum allowed value being 10922. 3 X 0 2 X 0 MFR_SPECIFIC_ALPHA: Allows the user to program the value of the ALPHA compensation coefficient. The allowed range is 1 Other Communication Fault 0 -256 to 256. The entire 16 bits are used to enter this range of 0 X 0 integer values in two’s complement binary format. For stable operation, use positive values only as suggested with MFR_SPECIFIC_00: Returns information related to the type of the maximum allowed value being 256. module and revision number. Bits [7:2] in the Low Byte indicate the module type (001101 corresponds to the TJT120 series of module), while bits [7:3] in the high byte indicate the revision number of the module. Low Byte Bit Default Flag Position Value 7:2 Module Name 001101 1:0 Reserved 10 High Byte January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 21 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Summary of Supported PMBus Commands Please refer to the PMBus 1.1 specification for more details of these commands. For the registers where a range is specified, any value outside the range is ignored and the module continues to use the previous value. Table 4 Hex Non-Volatile Command Brief Description Code Memory Storage Turn Module on or off. Also used to margin the output voltage Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 01 OPERATION YES Access r/w r r/w r/w r/w r/w r r Function On X Margin X X Default Value 1 0 0 0 0 0 X X Configures the ON/OFF functionality as a combination of analog ON/OFF pin and PMBus commands Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 02 ON_OFF_CONFIG YES Access r r r r/w r/w r/w r r Function X X X pu cmd cpr X cpa Default Value 0 0 0 1 0 1 x 1 Clear any fault bits that may have been set, also releases the SMBALERT# signal if the 03 CLEAR_FAULTS device has been asserting it. Used to control writing to the module via PMBus. Copies the current register setting in the module whose command code matches the value in the data byte into non-volatile memory (EEPROM) on the module Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w x x x x x Function bit7 bit6 bit5 X X X X X Default Value 0 0 0 X X X X X 10 WRITE_PROTECT YES Bit5: 0 – Enables all writes as permitted in bit6 or bit7 1 – Disables all writes except the WRITE_PROTECT, OPERATION and ON_OFF_CONFIG (bit 6 and bit7 must be 0) Bit 6: 0 – Enables all writes as permitted in bit5 or bit7 1 – Disables all writes except for the WRITE_PROTECT and OPERATION commands (bit5 and bit7 must be 0) Bit7: 0 – Enables all writes as permitted in bit5 or bit6 1 – Disables all writes except for the WRITE_PROTECT command (bit5 and bit6 must be 0) Copies all current register settings in the module into non-volatile memory (EEPROM) 11 STORE_DEFAULT_ALL on the module. Takes about 50ms for the command to execute. Restores all current register settings in the module from values in the module non- 12 RESTORE_DEFAULT_ALL volatile memory (EEPROM) The module has MODE set to Linear and Exponent set to -14. These values cannot be changed Bit Position 7 6 5 4 3 2 1 0 20 VOUT_MODE Access r r r r r r r r Function Mode 2’s complement Exponent Default Value 0 0 0 1 0 0 1 0 Set desired output voltage. Only 16-bit unsigned mantissa – implied exponent of -14 per VOUT_MODE command. Valid range is 0.6 to 1.5V. Format Unsigned Mantissa Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w 21 VOUT_COMMAND Function Mantissa YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 22 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Apply a fixed offset voltage to the set output voltage from either the RTrim resistor or the VOUT_COMMAND. Implied exponent of -14 per VOUT_MODE command. Allowed range is ±300mV. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w 22 VOUT_TRIM YES Function Mantissa Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 0 0 0 Applies an offset to the commanded output voltage to calibrate out errors in setting module output voltage (between -100mV and +100mV) and when output voltage is set via the PMBus command VOUT_COMMAND (21). Implied exponent of -14 per VOUT_MODE command. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r r r r r r r 23 VOUT_CAL_OFFSET YES Function Mantissa Default Value Variable based on factory calibration Bit Position 7 6 5 4 3 2 1 0 Access r r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable based on factory calibration Sets the target voltage for margining the output high. Implied exponent of -14 per VOUT_MODE command. Allowed range is 0.6 to 1.5V Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa 25 VOUT_MARGIN_HIGH YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Sets the target voltage for margining the output low. Implied exponent of -14 per VOUT_MODE command. Allowed range is 0.6 to 1.5V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa 26 VOUT_MARGIN_LOW YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Sets the value of input voltage at which the module turns on. Exponent is fixed at -6. Allowed range is 7 to 14V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w Function Exponent Mantissa 35 VIN_ON YES Default Value 1 1 0 1 0 0 0 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 1 0 0 0 0 0 0 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 23 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Sets the value of input voltage at which the module turns off. Exponent is fixed at -6. Allowed range is 6.75 to 14V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w 36 VIN_OFF Function Exponent Mantissa YES Default Value 1 1 0 1 0 0 0 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 1 1 0 0 0 0 Applies a gain correction to the READ_IOUT command results to calibrate out gain errors in module measurements of the output current. The number in this register is divided by 8192 to generate the correction factor. Allowed range is 6553 to 9830. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r/w 38 IOUT_CAL_GAIN YES Function Integer Default Value Variable based on factory calibration Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable based on factory calibration Returns the value of the offset correction term used to correct the measured output current. The exponent is fixed at -2. The allowed range is -50 to +50A. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r/w r r Function Exponent Mantissa 39 IOUT_CAL_OFFSET YES Default Value 1 1 1 1 0 Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable based on factory calibration Sets the voltage level for an output overvoltage fault. Implied exponent of -14 per VOUT_MODE command. Allowed range is 0.6 to 2V. Format Linear, two’s compliment binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w 40 VOUT_OV_FAULT_LIMIT Function Mantissa YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Instructs the module on what action to take in response to an output overvoltage fault Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 41 VOUT_OV_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r r YES RSP RSP Function RS[2] RS[1] RS[0] X X X [1] [0] Default Value 1 0 1 1 1 0 0 0 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 24 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Sets the value of output voltage at which the module generates warning for over-voltage. Exponent is fixed at -14. Allowed range is 0.6 to 2V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r/w r/w r/w Function Exponent Mantissa 42 VOUT_OV_WARN_LIMIT YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Sets the value of output voltage at which the module generates warning for under-voltage. Exponent is fixed at -14. Allowed range is 0.05 to 1.5V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r/w r/w r/w Function Exponent Mantissa 43 VOUT_UV_WARN_LIMIT YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Sets the voltage level for an output undervoltage fault. Exponent is fixed at -14. Allowed range is 0.05 to 2V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r/w r/w r/w Function Exponent Mantissa 44 VOUT_UV_FAULT_LIMIT YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Instructs the module on what action to take in response to an output undervoltage fault Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 45 VOUT_UV_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r r YES RSP RSP Function RS[2] RS[1] RS[0] X X X [1] [0] Default Value 1 0 1 1 1 0 0 0 Sets the current level for an output overcurrent fault (can only be lowered below the maximum of 140A). The exponent is fixed at -2 Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w 46 IOUT_OC_FAULT_LIMIT Function Exponent Mantissa YES Default Value 1 1 1 1 0 0 1 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 1 0 0 0 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 25 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Sets the value of current level at which the module generates warning for overcurrent. Allowed range is 0 to 140A. The exponent is fixed at -2. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r/w Function Exponent Mantissa 4A IOUT_OC_WARN_LIMIT YES Default Value 1 1 1 1 0 0 1 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 1 0 1 0 0 0 Sets the temperature level above which over-temperature fault occurs. Allowed range is 35 to 140°C. The exponent is fixed at 0. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r/w r r 4F OT_FAULT_LIMIT Function Exponent Mantissa YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 0 0 1 0 1 0 Configures the over temperature fault response Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 50 OT_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r r YES RSP RSP Function RS[2] RS[1] RS[0] X X X [1] [0] Default Value 1 0 1 1 1 0 0 0 Sets the over temperature warning level in °C. Allowed range is 30 to 130°C. The exponent is fixed at 0. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r 51 OT_WARN_LIMIT YES Function Exponent Mantissa Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 1 1 1 1 1 0 1 Sets the input overvoltage fault limit. Exponent is fixed at -6. Allowed range is 6.75 to 15V. Format Linear, two’s complement binary. Bit Position 15 14 13 12tr 11 10 9 8 Access r r r r r r r/w r/w Function Exponent Mantissa 55 VIN_OV_FAULT_LIMIT YES Default Value 1 1 0 1 0 0 1 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 1 0 0 0 0 0 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 26 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Configures the VIN overvoltage fault response. Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 56 VIN_OV_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r r YES RSP RSP Function RS[2] RS[1] RS[0] X X X [1] [0] Default Value 1 0 0 0 0 0 0 0 Sets the value of the input voltage that causes input voltage low warning. Exponent fixed at -6. Allowed range is 6.75 to 15V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w Function Exponent Mantissa 57 VIN_OV_WARN_LIMIT YES Default Value 1 1 0 1 0 0 1 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 0 0 0 0 0 0 Sets the value of the input voltage that causes input voltage low warning. Exponent fixed at -6. Allowed range is 5 to 14V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w 58 VIN_UV_WARN_LIMIT Function Exponent Mantissa YES Default Value 1 1 0 1 0 0 0 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 1 0 0 0 0 0 Sets the value of the input voltage that causes an input undervoltage fault. Exponent fixed at -6. Allowed range is 5 to 14V. Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r/w r/w 59 VIN_UV_FAULT_LIMIT Function Exponent Mantissa YES Default Value 1 1 0 1 0 0 0 1 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 1 0 1 0 0 0 0 0 Instructs the module on what action to take in response to an input undervoltage fault. Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 5A VIN_UV_FAULT_RESPONSE Access r/w r/w r/w r/w r/w r r r YES RSP RSP Function RS[2] RS[1] RS[0] X X X [1] [0] Default Value 1 0 1 1 1 0 0 0 Sets the output voltage level at which the PGOOD pin is asserted high. Implied exponent of -14 per VOUT_MODE command. Allowed range is 0.09 to 1.65V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r/w r/w r/w r/w r/w r/w r/w 5E POWER_GOOD_ON Function Mantissa YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 27 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (continued) Hex Non-Volatile Command Brief Description Code Memory Storage Sets the output voltage level at which the PGOOD pin is de-asserted low. Implied exponent of -14 per VOUT_MODE command. Allowed range is 0.06 to 1.63V. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r/w r/w r/w r/w r/w r/w r/w 5F POWER_GOOD_OFF Function Mantissa YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable Sets the delay time in ms of the output voltage during startup. Allowed range is 0 to 1000ms. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r/w r/w Function Exponent Mantissa 60 TON_DELAY YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 0 1 0 Sets the rise time in ms of the output voltage during startup. The exponent is fixed at 0. Allowed range is 1 to 1000ms. Format Linear, two’s complement binary Bit Position 7 6 5 4 3 2 1 0 Access r r R r r r r/w r/w 61 TON_RISE Function Exponent Mantissa YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 1 0 1 Sets the delay time in ms of the output voltage during turn-off. The exponent is fixed at 0. Allowed range is 0 to 1000ms. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r R r r r r/w r/w 64 TOFF_DELAY Function Exponent Mantissa YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 0 1 0 Sets the fall time in ms of the output voltage during turn-off. Exponent is fixed at 0. Allowed range is 0 to 1000ms. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r R r r r r/w r/w Function Exponent Mantissa 65 TOFF_FALL YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value 0 0 0 0 0 1 0 1 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 28 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (Continued) Hex Non-Volatile Command Brief Description Code Memory Storage Returns one byte of information with a summary of the most critical module faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 78 STATUS_BYTE Access r r R r r r r r Flag X OFF VOUT_OV IOUT_OC VIN_UV TEMP CML OTHER Default Value Variable Returns two bytes of information with a summary of the module’s fault/warning conditions Format Unsigned binary Bit Position 15 14 13 12 11 10 9 8 Access r r R r r r r r Flag VOUT IOUT_OC INPUT X PGOOD X X X 79 STATUS_WORD Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r R r r r r r Flag X OFF VOUT_OV IOUT_OC VIN_UV TEMP CML OTHER Default Value Variable Returns one byte of information with the status of the module’s output voltage related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 7A STATUS_VOUT Access r r r r r r r r VOUT_OV_ VOUT_UV_ Flag VOUT_OV VOUT_UV X X X X Warn Warn Default Value Variable Returns one byte of information with the status of the module’s output current related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 7B STATUS_IOUT Access r r r r r r r r Flag IOUT_OC X X X IOUT_OC_WARN X X X Default Value Variable Returns one byte of information with the status of the module’s input related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r 7C STATUS_INPUT Flag VIN_OV_FAULT VIN_OV_W VIN_UV_ VIN_UV X X X X ARNING WARNING _FAULT Default Value Variable Returns one byte of information with the status of the module’s temperature related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 7D STATUS_TEMPERATURE Access r r r r r r r r Flag OT_FAULT OT_WARN X X X X X X Default Value Variable Returns one byte of information with the status of the module’s communication related faults Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r 7E STATUS_CML Invalid Invalid PEC Flag X X X Other Comm Fault X Command Data Fail Default Value Variable January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 29 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (Continued) Hex Non-Volatile Command Brief Description Code Memory Storage Returns the value of the input voltage applied to the module. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Exponent Mantissa 88 READ_VIN Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value Variable Returns the value of the output voltage of the module. Exponent is fixed at -14 Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Mantissa 8B READ_VOUT Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value Variable Returns the value of the output current of the module. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Exponent Mantissa 8C READ_IOUT Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value Variable Returns a module FET package temperature in ºC. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Exponent Mantissa 8D READ_TEMPERATURE_1 Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value Variable Returns the module PWM controller temperature in ºC. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Exponent Mantissa 8E READ_TEMPERATURE_2 Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Mantissa Default Value Variable January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 30 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (Continued) Hex Non-Volatile Command Brief Description Code Memory Storage Returns the switching Frequency of the converter. The Frequency is in Kilohertz and is read only, consisting of two bytes. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r 95 READ_FREQUENCY Function Integer Default Value 0 0 0 0 0 0 0 1 Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Integer Default Value 1 0 0 1 0 0 0 0 Returns one byte indicating the module is compliant to PMBus Spec. 1.1 Format Unsigned Binary 98 PMBUS_REVISION Bit Position 7 6 5 4 3 2 1 0 YES Access r r r r r r r r Default Value 0 0 0 1 0 0 0 1 Value used to program specific proportional coefficient of the PID compensation Block. Allowable range: -10922 to +10922. Use positive values only Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer B0 MFR_SPECIFIC_KP YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable Value used to program specific integral coefficient of the PID compensation Block. Allowable range: -10922 to +10922. Use positive values only Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer B1 MFR_SPECIFIC_KI YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable Value used to program specific differential coefficient of the PID compensation. Allowable range: -10922 to +10922. Use positive values only Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer B2 MFR_SPECIFIC_KD YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable Value used to program specific alpha value of the PID compensation block Allowable range: -256 to +256. Use positive values only Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer B3 MFR_SPECIFIC_ALPHA YES Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 31 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (Continued) Hex Non-Volatile Command Brief Description Code Memory Storage Returns module name information (read only) Format Unsigned Binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Reserved D0 MFR_SPECIFIC_00 YES Default Value 0 0 0 0 0 0 0 0 Bit Position 7 6 5 4 3 2 1 0 Access r r r r r r r r Function Module Name Reserved Default Value 0 0 1 1 0 1 0 0 Applies an offset to the READ_VOUT command results to calibrate out offset errors in module measurements of the output voltage (between -125mV and +124mV). Exponent is fixed at -14. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w D4 MFR_READ_VOUT_CAL_OFFSET YES Function Mantissa Default Value Variable based on factory calibration Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable based on factory calibration Applies a gain correction to the READ_VOUT command results to calibrate out gain errors in module measurements of the output voltage. The number in this register is divided by 8192 to generate the correction factor. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w D5 MFR_READ_VOUT_CAL_GAIN YES Function Integer Default Value Variable based on factory calibration Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer Default Value Variable based on factory calibration Applies an offset to the commanded output voltage to calibrate out errors in setting module output voltage (between -63mV and +62mV) when using Trim resistor. Exponent is fixed at -14. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w D7 MFR_VOUT_CAL_OFFSET YES Function Mantissa Default Value Variable based on factory calibration Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Mantissa Default Value Variable based on factory calibration Bit 7 used to determine whether output voltage is set using RTrim or the YES VOUT_COMMAND. Bit 7: 1 – Output voltage is solely set by RTrim value and can be adjusted from set value using the VOUT_TRIM command Bit 7: 0 – Output voltage is solely set by VOUT_COMMAND and can be adjusted from set value using the VOUT_TRIM command. Bit 0: Used to indicate whether changes have been made to the Vout set point, PG On/Off levels, margin levels or OV/UV fault/warning levels. A 1 in this position D8 MFR_VOUT_SET_MODE indicates that one or more of the values have changed from the default. If this bit is 0, then the default values are used. Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w VOUT_SE Flag X X X X X X USER_CHANGES T_MODE Default Value 1 0 0 0 0 0 0 0 January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 32 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Table 4 (Continued) Hex Non-Volatile Command Brief Description Code Memory Storage Value used to program the firmware revision. This command is read only. Format Linear, two’s complement binary Bit Position 15 14 13 12 11 10 9 8 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer – Major Version DB MFR_FW_REVISION Default Value Variable Bit Position 7 6 5 4 3 2 1 0 Access r/w r/w r/w r/w r/w r/w r/w r/w Function Integer – Minor Version Default Value Variable Returns the index derived from the resistor strapped to the RTUNE pin of the module. Range is from 0 to 59. Format Unsigned Binary Bit Position 7 6 5 4 3 2 1 0 DD MFR_RTUNE_INDEX YES Access r r r r r r r r Function Integer Default Value Variable Gets or sets the write protection status of various PMBus commands. When a bit is set, the corresponding PMBus command is write protected and can only be read. Format Unsigned Binary Bit Position 15 14 13 12 11 10 9 8 Access r r r r r r r r Function Reserved Default Value x x x x x x x x Bit Position 7 6 5 4 3 2 1 0 DF MFR_WRITE_PROTECT YES Access r r r r r/w r/w r/w r/w Function Reserved Used Default Value x x x x 1 1 1 0 Bit 0: ON_OFF_CONFIG Bit 1: IOUT_OC_FAULT_LIMIT Bit 2: OT_FAULT_LIMIT Bit 3: OT_FAULT_RESP Bits 4 – 15: Reserved Read only command which returns 12 bytes with the value of YYFFWWXXXXXX, where YY : year of manufacture MFR_MODULE_DATE_LOC FF: Factory where manufactured F0 YES _SN WW: Fiscal week of the year when unit was manufactured XXXXXX: Unique number for the specific unit – corresponding to serial number on the label of the unit. SMBALERT# is also triggered: • when an invalid/unrecognized PMBus command (write or read) is issued • By invalid PMBus data (write) • By PEC Failure (when used) • By Enable OFF (when used) • Module is out of Power Good Range Digital Power Insight (DPI) GE offers a software tool that set helps users evaluate and simulate the PMBus performance of the TJT170A modules without the need to write software. The software can be downloaded for free at http://go.ge-energy.com/DigitalPowerInsight.html. A GE USB to I2C adapter and associated cable set are required for proper functioning of the software suite. For first time users, the GE DPI Evaluation Kit can be purchased from leading distributors at a nominal price and can be used across the entire range of GE Digital POL Modules. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 33 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 37. The preferred airflow direction for the module is in Figure 38. 25.4_ Wind Tunnel (1.0) PWBs Power Module Figure 38. Preferred airflow direction and location of hot- 76.2_ spots of the module (Tref). (3.0) The thermal reference points, T used in the specifications ref x are also shown in Figure 38. For reliable operation the temperatures at these points should not exceed 120°C. The Probe Location output power of the module should not exceed the rated for measuring 12.7_ airflow and power of the module (Vo,set x Io,max). (0.50) ambient temperature Please refer to the Application Note “Thermal Characterization Process For Open-Frame Board-Mounted Air Power Modules” for a detailed discussion of thermal aspects flow including maximum device temperatures. Figure 37. Thermal Test Setup. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 34 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Example Application Circuit Requirements: Vin: 12V Vout: 1.2V Iout: 120A max., worst case load transient is from 60A to 90A, 10A/usec Vout: 25mV for worst case load transient Vin, ripple 2% of Vin (240mV p-p) Vin+ Vout+ VIN VOUT VS+ PGOOD 3.3V* MODULE SEQ RTUNE CLK CI3 CI2 CI1 TRIM CO1 CO2 CO3 DATA RTUNE ADDR0 SMBALRT# RTrim ADDR1 ON/OFF RADDR1 RADDR0 Q1 SIG_GND GND VS - GND 3.3V* can be derived from Vin through a suitable voltage divider network CI1 4 x 0.047 µF (high-frequency decoupling ceramic capacitor) CI2 12 x 22 µF Ceramic CI3 4 x 470 µF (polymer or electrolytic) CO1 4 x 0.047 µF (high-frequency decoupling ceramiccapacitor) CO2 12 x 47 µF, Ceramic CO3 7 x 1000 µF RTune 2460Ω, RTrim 5.9KΩ Note: The DATA, CLK and SMBALRT pins do not have any pull-up resistors inside the module. Typically, the PMBus master controller will have pull-up resistors as well as provide the driving source for these signals. If running the simulation at ge.transim.com remember to use bin ‘a’ parameters to determine the Loop Stability, and bin ‘b’ parameters to determine the transient response. January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 35 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Mechanical Outline (SMT) Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated] x.xx mm  0.25 mm (x.xxx in  0.010 in.) BOTTOM VIEW January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 36 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Recommended SMT Pad Layout PIN FUNCTION PIN FUNCTION PIN FUNCTION 1 VOUT 15 PWR_GOOD 29 VIN 2 VOUT 16 RTUNE 30 N/A 3 GND 17 TRIM 31 SHARE/NC 4 VOUT 18 SEQ 32 ON/OFF 5 VOUT 19 SIG_GND 33 SMBALERT# 6 GND 20 VS+ 34 DATA 7 VOUT 21 VS- 35 CLK 8 VOUT 22 GND 36 ADDR0 9 GND 23 VIN 37 ADDR1 10 VOUT 24 GND 38 GND 11 VOUT 25 VIN 12 GND 26 GND 13 GND 27 VIN 14 SYNC 28 GND January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 37 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Mechanical Outline (Through hole) Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated] x.xx mm  0.25 mm (x.xxx in  0.010 in.) BOTTOM VIEW January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 38 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Recommended Through-hole Layout Note: In the Through-Hole version of the TJT120, pins 1-13, 22-29 and 38 are Through-Hole pins, pins 14-21, 30-37 are SMT pins. The drawing above shows the recommended layout as a combination of holes in the PWB to accommodate the Through-Hole pins and pads on the top layer to accommodate the SMT pins. PIN FUNCTION PIN FUNCTION PIN FUNCTION 1 VOUT 15 PWR_GOOD 29 VIN 2 VOUT 16 RTUNE 30 N/A 3 GND 17 TRIM 31 SHARE/NC 4 VOUT 18 SEQ 32 ON/OFF 5 VOUT 19 SIG_GND* 33 SMBALERT# 6 GND 20 VS+ 34 DATA 7 VOUT 21 VS- 35 CLK 8 VOUT 22 GND 36 ADDR0 9 GND 23 VIN 37 ADDR1 10 VOUT 24 GND 38 GND 11 VOUT 25 VIN 12 GND 26 GND 13 GND 27 VIN 14 SYNC 28 GND *Do not connect SIG_GND to any other GND paths. It needs to be kept separate from other grounds on the board external to the module January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 39 Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Packaging Details TM The 120A TeraDLynx modules are supplied in trays. Modules are shipped in quantities of 12 modules per layer, 24 per box. All Dimensions are in millimeters. All radius unspecified are R2.0mm. All angles unspecified are 5°. * Unit datecodes prior to 1802 will have the older taller tray with a height of 34.00±0.5 as indicated January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 40 34.00±0.5* Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 7Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current conditions of  30°C and 60% relative humidity varies Surface Mount Information according to the MSL rating (see J-STD-033A). The shelf life Pick and Place for dry packed SMT packages will be a minimum of 12 TM months from the bag seal date, when stored at the following The 120A TeraDLynx modules use an open frame conditions: < 40° C, < 90% relative humidity. construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place Peak Temp. 240-245°C operations. The label meets all the requirements for surface mount processing, as well as safety standards, and is able o Ramp down to withstand reflow temperatures of up to 300 C. The label max. 4°C/Sec also carries product information such as product code, 217°C serial number and the location of manufacture. 200°C Time Limited 90 Sec. Nozzle Recommendations above 217°C 150°C The module weight has been kept to a minimum by using Preheat time open frame construction. Variables such as nozzle size, tip 100-150 Sec. style, vacuum pressure and placement speed should be Ramp up considered to optimize this process. The minimum max. 3°C/Sec recommended inside nozzle diameter for reliable operation 25°C Time is 15mm. The maximum nozzle outer diameter, which will Figure 39. Recommended linear reflow profile using safely fit within the allowable component spacing, is 22 mm. Sn/Ag/Cu solder. Bottom Side / First Side Assembly Post Solder Cleaning and Drying Considerations This module is not recommended for assembly on the bottom side of a customer board. If such an assembly is Post solder cleaning is usually the final circuit-board attempted, components may fall off the module during the assembly process prior to electrical board testing. The result second reflow process. of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the Lead Free Soldering finished circuit-board assembly. For guidance on The modules are lead-free (Pb-free) and RoHS compliant appropriate soldering, cleaning and drying procedures, refer and fully compatible in a Pb-free soldering process. Failure to Board Mounted Power Modules: Soldering and Cleaning to observe the instructions below may result in the failure of Application Note (AN04-001). or cause damage to the modules and can adversely affect long-term reliability. Through Hole Information Pb-free Reflow Profile TM The 120A TeraDLynx modules are lead-free (Pb-free) and Power Systems will comply with J-STD-020 Rev. C RoHS compliant and fully compatible in an Pb-free soldering (Moisture/Reflow Sensitivity Classification for Nonhermetic process. For the through-hole application, it is Solid State Surface Mount Devices) for both Pb-free solder recommended that the modules are assembled in the pin profiles and MSL classification procedures. This standard and paste reflow process, not in the wave solder process. provides a recommended forced-air-convection reflow Failure to observe the instructions below may result in the profile based on the volume and thickness of the package failure of or cause damage to the modules and can (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu adversely affect long-term reliability. (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Fig. 40. Soldering outside of the recommended profile requires testing to verify results and performance. MSL Rating TM The 120A TeraDLynx modules have a MSL rating of 3. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at January 18, 2018 ©2017 General Electric Company. All rights reserved. Page 41 Temp Data Sheet GE TM 120A TeraDLynx : Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.6Vdc to 1.5Vdc output; 120A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 5. Device Codes Input Output Output On/Off Device Code Interconnect Comcodes Voltage Range Voltage Current Logic TJT120A0X3Z 7 – 14Vdc 0.6 – 1.5 Vdc 120A Negative TH 150043982 TJT120A0X43Z 7 – 14Vdc 0.6 – 1.5 Vdc 120A Positive TH 150049601 TJT120A0X3-SZ 7 – 14Vdc 0.6 – 1.5 Vdc 120A Negative SMT 150041745 TJT120A0X43-SZ 7 – 14Vdc 0.6 – 1.5 Vdc 120A Positive SMT 150049603 -Z refers to RoHS compliant parts Table 6. Coding Scheme Package Sequencing Output Output On/Off Remote Options Family ROHS Compliance Identifier Option current voltage logic Sense -H T J T 120A0 X 3 -SR Z P=Pico J = T=with EZ 120A X = 4 = 3 = S = Surface Extra Ground Z = ROHS6 DLynx ΙΙ Sequence programm positive Remote Mount Pins U=Micro able Sense X=without No entry = R = Tape & output M=Mega sequencing negative Reel No entry = G=Giga Through hole T=Tera GE Digital Non-Isolated DC-DC products use technology licensed from Power-One, protected by US patents: US20040246754, US2004090219A1, US2004093533A1, US2004123164A1, US2004123167A1, US2004178780A1, US2004179382A1, US20050200344, US20050223252, US2005289373A1, US20060061214, US2006015616A1, US20060174145, US20070226526, US20070234095, US20070240000, US20080052551, US20080072080, US20080186006, US6741099, US6788036, US6936999, US6949916, US7000125, US7049798, US7068021, US7080265, US7249267, US7266709, US7315156, US7372682, US7373527, US7394445, US7456617, US7459892, US7493504, US7526660. Outside the US the Power-One licensed technology is protected by patents: AU3287379AA, AU3287437AA, AU3290643AA, AU3291357AA, CN10371856C, CN1045261OC, CN10458656C, CN10459360C, CN10465848C, CN11069332A, CN11124619A, CN11346682A, CN1685299A, CN1685459A, CN1685582A, CN1685583A, CN1698023A, CN1802619A, EP1561156A1, EP1561268A2, EP1576710A1, EP1576711A1, EP1604254A4, EP1604264A4, EP1714369A2, EP1745536A4, EP1769382A4, EP1899789A2, EP1984801A2, W004044718A1, W004045042A3, W004045042C1, W004062061 A1, W004062062A1, W004070780A3, W004084390A3, W004084391A3, W005079227A3, W005081771A3, W006019569A3, W02007001584A3, W02007094935A3 Contact Us For more information, call us at USA/Canada: +1 888 546 3243, or +1 972 244 9288 Asia-Pacific: +86.021.54279977*808 Europe, Middle-East and Africa: +49.89.878067-280 www.gecriticalpower.com GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Version 1.12 January 18, 2018 ©2017 General Electric Company. All International rights reserved.