Optical and Mechanical Encoders Optical Encoders SERIES 60C Multi-Function Joystick FEATURES • Three-in-One Joystick, Optical Encoder and Pushbutton • Compact Packaging • Choices of Cable Length and Termination • Customized Solutions Available APPLICATIONS • Avionics • Medical Equipment • Automotive Navigation, Information & Entertainment Equipment The 60C is a cost-effective replacement of a stationary mouse or trackball with improved control over cursor move- ment. An integral Schmitt Trigger is used to stabilize against noise and vibration. As a compact cursor control device, Grayhill's Series 60C is ideally suited for automotive and aviation dashboards, where use of separate joysticks, encoders and pushbuttons might be impractical. It provides all the functionality of a stationary mouse or trackball in a single unit with a 1"x1"x .661" deep housing. The joystick manipulates a cursor left, right, up and down; the rotary encoder facilitates sequential scrolling through menu options; and the pushbutton performs on-screen menu selects. DIMENSIONS in inches (and millimeters) Unless otherwise specified, standard tolerance are: Linear ± .025 Diameter ± .010 Angle ± 2.0° Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com Optical and Mechanical Encoders Optical Encoders MOUNTING DETAILS in inches (and millimeters) FRONT MOUNTING REAR MOUNTING JOYSTICK OPERATION + ENCODER WAVEFORM AND TRUTH TABLE Standard Quadrature 2-Bit Code JOYSTICK ENCODER Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com Optical and Mechanical Encoders Optical Encoders SWITCH SCHEMATIC SPECIFICATIONS Slider Plate: Thermoplastic Rotary Pushbutton Backplate: Thermplastic Electrical and Mechanical Ratings Electrical and Mechanical Ratings Lightpipe, Joystick: Thermoplastic Operating Voltage: 5.00 ± 0.25 Vdc Rating: 10 mA at 5 Vdc resistive Lightpipe, 16 pos: Thermoplastic Supply Current: 35mA TYP at 5 Vdc Contact Resistance: less than 10 ohms Centering Profile: Thermoplastic Power Consumption: 175mW TYP at 5Vdc Contact Bounce: < 4ms make, 10 ms break Shaft Inner: Aluminum Output: Direct output from inverting Schmitt Mechanical Life: 500K actuations minimum Pins: Stainless steel trigger Actuation Force: option 7 = 485 ± 115grams Barbed Rivet: Stainless steel Output Code: 2-Bit quadrature, channel A Pushbutton Travel: 0.033 ± 0.015 inches to Detent Balls: Carbon steel 100 with nickel leads channel B by 90° in cw rotation contact; 0.075 inches maximum finish Logic Output Characteristics: Centering Balls: Carbon steel 100 with nickel High: No less than 3.5 Vdc Environmental Ratings finish Low: No greater than 1.0 Vdc Operating Temperature Range: -40°C to Detent Springs: Tinned music wire Mechanical Life: 500K rotational cycles 85°C Centering Springs: Tinned music wire (through all positions and a full return) Storage Temperature Range: -55°C to Cable ASM: .050 round conductor flat cable, Rotational Torque: medium torque option 100°C PVC coated. Conductors are stranded, top- 3.00+2.00 in-oz, torque shall be within 50% of Relative Humidity: 96 hours at 90-95% coated wire initial value throughout life humidity at 40°C Solder: 95.5% SN, 4% AG, 0.5% CU Mounting Torque: 15 in-oz. maximum Vibration: Harmonic motion with amplitude of Dome: Stainless steel Shaft Push/Pull Out Force: 25 lbs minimum 15g, within a varied 10 to 2000 Hz PCB 16 Pos: NEMA grade FR-4. Plating is Terminal Strength: 15 lbs terminal minimum Mechanical Shock: gold or palladium over nickel Test 1: 100g for 6ms half-sine wave with a Infrared Emitter: Gallium aluminum arsenide velocity change of 12.3 ft/s Joystick Phototransistor: Planar silicon Test 2: 100g for 6ms sawtooth wave with a Electrical and Mechanical Ratings Resistor: Carbon film velocity change of 9.7 ft/s Operating Voltage: 5.00 ± 0.25 Vdc Schmitt Trigger: RoHS Compliant TSSOP, Thermocycle: 4 hours cycling between Supply Current: 35mA at TYP at 5 Vdc 14 pin -40°C to 85°C Power Consumption: 175mW TYP at 5Vdc Lubricating Grease: Nyogel 774L Output: Direct output from inverting Schmitt Label: TT406 Thermal transfer cast film Materials and Finishes trigger Bushing: Thermoplastic Logic Output Characteristics: OPTIONS Shaft Outer: Thermoplastic High: No less than 3.5 Vdc Contact Grayhill for custom terminations, Low: No greater than 1.0 Vdc Upper Housing: Thermoplastic rotational torque, number of positions, shaft Pushbutton Rocker: Thermoplastic Mechanical Life: 500K cycles configurations, and resolutions. Control knobs (through all positions and a full return) Pushbutton Actuator: Thermoplastic Inner Shaft Slide: Thermoplastic are also available. Angle of Throw: 8° max. in all directions ORDERING INFORMATION Series Angle of Throw: 22= 22.5° or 16 positions Rotation Torque: M= Medium torque Pushbutton: 7= 485 grams Joystick: 4= Four directions 60C22-M7-4-060S Termination: 0.050" center ribbon cable with; C= Connector; S= 0.1" stripped end Cable Length: 025 thru 250 in 1/2 inch increments, 060= 6.0 inch cable Available from your local Grayhill Distributor. For prices and discounts, contact a local sales office, an authorized distributor, or Grayhill. Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com