GRAYHILL 62T22-M7-020C

Optical and Mechanical Encoders Optical Encoders SerieS 62T Thumbwheel with Pushbutton FeATUreS APPLiCATiONS • Scroll and select functions • Scroll & select equipment in industrial • Sealed against dust and particles and non-automotive transportation • Custom bezels that will blend with HMI grips applications and control panels • Display selectors • Optional integrated pushbutton with over • Hand-grip joysticks three million actuations • MIL-STD-202 and MIL-STD-810F Compliant • Standard panel seal • Choice of cable length and termination DiMeNSiONS in inches (and millimeters) Unless otherwise specified, standard tolerances are: Linear ± .025 Diameter ± .010 0 Angle ± 2.0 1.758 [ 44,65 ] Ø.200 ± .005 1.500 ± .005 .327 [ 38,1] [ 5,0 ] [ 8,31] .780 C-BORE [ 19,81] .265 X2 .020 [ 0,51] Ø.950 Ø.128 ± .002 CLOCKWISE ROTATION .114 ±.015 [ 24,13] [ 3,25 ] .485 [ 2,9 ] THRU HOLE [ 12,32 ] .830 X2 [ 21,08 ] .125 [ 3,18 ] OF .020 WHEEL .515 .650 [ 0,51 ] [ 13,08 ] [ 16,51 ] 4.00 ±.25 .640 [ 16,26 ] AMP CONNECTOR PN 7-215083-6 .970 [ 24,64 ] R.250 [ 6,35 ] Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com Optical and Mechanical Encoders Optical Encoders WAVeFOrM AND TrUTH TABLe 90˚± 45˚ +5Vdc 1 R* HIGH (3.8-5V) OUTPUT A OUTPUT B OUTPUT "A" 2 POSITION OUTPUT A R* 3 #1 OUTPUT "B" LOW (0-.8V) #2 GROUND 4 HIGH (3.8-5V) #3 OUTPUT B PUSHBUTTON 5 #4 N.O., MOMENTARY LOW (0-.8V) PUSHBUTTON SWITCH PUSHBUTTON 6 POS POS POS POS POS POS Indicates logic high; blank indicates logic low. #5 #1 #2 #3 #4 #6 Code repeats every 4 positions. R* - TWO 2.2K RESISTORS REQUIRED FOR OPERATION. SPeCiFiCATiONS environmental Specifications rotary electrical and Mechanical Materials and Finishes Face Plate: Plastic MIL-STD-810F Qualified Specifications 0 0 Housing: ABS Plastic Operating Temperature range: -40 C to 85 C Operating Voltage: 5.00±0.25 Vdc 0 0 Side Plate: Reinforced thermoplastic Storage Temperature range: -55 C to 100 C Supply Current: 25mA Max. Wiper: Silicone rubber with adhesive Humidity: 240 hours at 95% humidity Output: Open collector phototransistor, 0 Gasket: Silicone rubber with adhesive at 30 C external pull up resistors are required Wheel: Plastic Mechanical Vibration: Harmonic motion with Output Code: Two-bit quadrature, channel A Shaft: Aluminum amplitude of 15g, within a varied frequency of leads channel B by 90° electrically during Slide Springs: Music wire 10 to 2000 Hz clockwise rotation of the thumbwheel Detent Spring: Music wire Mechanical Shock: Logic high shall be no less than 3.8 Vdc Detent Balls: Nickel plated stainless steel Test 1: 100g for 6 ms half-sine wave with a Logic low shall be no greater than 0.8 Vdc PC Boards: NEMA grade FR4. Double clad velocity change of 12.3 ft/sec Power Consumption: 125 mW Max. with copper Test 2: 100g for 6 ms sawtooth wave with a Mechanical Life: 1,000,000 cycles of Plated with gold over nickel velocity change of 9.7 ft/sec operation for Low and Non-Rotational Torque. Pushbutton board is tin plating over copper 500,000 cycles of operation for Medium LeD: Gallium Aluminum Arsenide Rotational Torque. 1 cycle is a rotation Pushbutton electrical and Phototransistor: Gold and Aluminum Alloys through all positions and a full return. Mechanical Specifications Code Section Housing: Reinforced plastic Average rotational Torque: rating: 10mA @ 5 Vdc Detent Housing: Thermoplastic M: 2.2±.75 in-oz, L: 1.2±0.5 in-oz, N: <0.50 Contact resistance: <10ohms Code rotor: Delrin 100 plastic in-oz. Initially torque shall be within 75% of Life: 3 million actuations minimum Dome: Stainless steel initial value throughout life. Contact Bounce: <4 ms make, <10ms Dome retainer: Delrin 100 plastic break Slide rods: Stainless steel Actuation Force: N – None, 7–700g, Splining Key: Stainless steel 10 – 1000g. Actuator: Reinforced thermoplastic Thumbwheel Travel: .060 ± .015 in Screws: Aluminum or Stainless Wiper Plate: Copper Solder: Lead free (96.5% tin, 3% silver, 0.5% copper, no clean) Series Angle of Throw: 22 = 22.5° for code change and 16 detent positions Rotational Torque: N = Non-Detent, L=Low Torque, M=Medium Torque Pushbutton Option: 0=No Pushbutton, 7=700 grams, 10=1000 grams 62T22-XX-040C Termination: C = .050 Center ribbon Cable with connector Cable Termination: 040=4.0 inches. Cable is terminated with Amp Connector P/N 7-215083-6. See Amp Mateability Guide for Mating Connector details. Available from your local Grayhill Component Distributor. For pricing an discounts, contact a local Sales Office, an authorized local Distributor, or Grayhill. Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com