Ribbon Cable connector Compliant with MIL Standard HIF3B Series ■Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide applications. 2. UL Approval Product HIF3B series connectors are UL approved. 3. Mechanism to Prevent Mis-insertion This connector is equipped with the mechanism to prevent Mis- insertion as follows. 1 The system provides the convex area to insert the guide-key on the pin header side, and to guide it in combination with the socket convex area (MIL standard). 2 The system embeds and guides the polarizing key in the socket holes. 4. Applicable Cable AWG#28 The applicable cable is UL2651 AWG#28 flat cable (7 cores./ 0.127mm, jacket dia. 0.9±0.1mm). ■Product Specifications ( ) ( ) Current rating : 1A Operating Temperature Range : –55 to +85ç Note 1 Storage Temperature Range : –10 to +60ç Note 2 Rating ( ) Voltage rating : 200V AC Operating Moisture Range : 40 to 80% Storage Humidity Range : 40 to 70% Note 2 Item Specification Condition 1. Insulation Resistance 1000M ohms min. 500V DC 2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute 3. Contact Resistance 15m ohms max. 0.1A 4. Vibration No electrical discontinuity of 1μs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 1000M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% (-55ç: 30 minutes ➝ 15 to 35ç: 5 minutes max. 6. Temperature Cycle No damage, cracks, or parts looseness. 125ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 15m ohms max. 500 cycles Solder bath: 260ç for 10 seconds 8. Resistance to Soldering heat No deformation of components affecting performance. Manual soldering: 360ç for 5 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Note 4: Please note that there is a risk of deforming the lock when an excessive load is applied to the inside. ■Material Part Material Finish Remarks Insulator PBT Black UL94V-0 Socket Contact Beryllium copper Connection area Gold plated ––––––– Pin header contact Brass Selective Gold plated ––––––– B15 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Ordering Information ●Socket HIF 3B - * D - 2.54 R qw et r y q Series Name : HIF ( ) w Series No. : 3B, 3BA, 3BB 50, 60, 64 contacts only e Number of contacts : 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64 r Contact alignment : D : Double t Contact pitch : 2.54mm y Connection type R : ID type ●Pin Header HIF 3B - * P A - 2.54 DS qw et r y u q Series Name : HIF w Series No. : 3B : (14 contacts not included) 3BC: (10 contacts only) 3BA, 3BB: (50, 60, 64 contacts only) 3BD: (10 contacts only) e Number of contacts : 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64 r P : Pin header t A : Selective gold plated y Contact pitch : 2.54mm u Contact style DS : Right angle type DSA : Straight type B16 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket (With guide to prevent mis-insertion) Body Protector Clamp Note1, Note2: The number of polarizing keys and polarizing keyways changes according to products. Refer to the list as shown below. Note3: The 50, 60 and 64 contact connector contain two types of polarizing guides. Use the products, referring to Notes 1 and 2. Note4: The 6 contact has no polarizing mark. Unit:mm Polarizing Guide Polarizing Keyway Part Number CL No. Number of Contacts A B C D RoHS (Note 1) (Note 2) HIF3BA- 6D-2.54R 610-0032-3 6 12.19 5.08 6.35 7.72 None HIF3BA-10D-2.54R 610-0021-7 10 17.27 10.16 11.43 12.8 One on left side ★ HIF3BA-14D-2.54R 610-0022-0 14 22.35 15.24 16.51 17.88 ★ HIF3BA-16D-2.54R 610-0023-2 16 24.89 17.78 19.05 20.42 ★ HIF3BA-20D-2.54R 610-0024-5 20 29.97 22.86 24.13 25.5 One at center ★ HIF3BA-26D-2.54R 610-0025-8 26 37.59 30.48 31.75 33.12 ★ HIF3BA-30D-2.54R 610-0026-0 30 42.67 35.56 36.83 38.2 YES ★ HIF3BA-34D-2.54R 610-0027-3 34 47.75 40.64 41.91 43.28 ★ HIF3BA-40D-2.54R 610-0028-6 40 55.37 48.26 49.53 50.9 One on right and ★ HIF3BA-50D-2.54R 610-0029-9 50 68.07 60.96 62.23 63.6 One on right and left sides, resp. left sides, resp. ★ HIF3BB-50D-2.54R 610-0041-4 50 68.07 60.96 62.23 63.6 One at center ★ HIF3BA-60D-2.54R 610-0030-8 60 80.77 73.66 74.93 76.3 One on right and left sides, resp. ★ HIF3BB-60D-2.54R 610-0042-7 60 80.77 73.66 74.93 76.3 One at center ★ HIF3BA-64D-2.54R 610-0031-0 64 85.85 78.74 80.01 81.38 One on right and left sides, resp. ★ HIF3BB-64D-2.54R 610-0043-0 64 85.85 78.74 80.01 81.38 One at center The products marked with ★ comply with MIL standard. B17 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket Body Protector Clamp Note1: The number of polarizing keys and polarizing keyways changes according to products. For details, refer to the list as shown below. Note2: The 6 contact has no polarizing mark. Unit:mm Polarizing Guide Part Number CL No. Number of Contacts A B C D RoHS (Note 1) HIF3B- 6D-2.54R 610-0012-6 6 12.19 5.08 6.35 7.72 None ★ HIF3B-10D-2.54R 610-0001-0 10 17.27 10.16 11.43 12.80 One on left side ★ HIF3B-14D-2.54R 610-0002-2 14 22.35 15.24 16.51 17.88 ★ HIF3B-16D-2.54R 610-0003-5 16 24.89 17.78 19.05 20.42 ★ HIF3B-20D-2.54R 610-0004-8 20 29.97 22.86 24.13 25.50 ★ HIF3B-26D-2.54R 610-0005-0 26 37.59 30.48 31.75 33.12 YES ★ HIF3B-30D-2.54R 610-0006-3 30 42.67 35.56 36.83 38.2 One on right and ★ HIF3B-34D-2.54R 610-0007-6 34 47.75 40.64 41.91 43.28 left sides, resp. ★ HIF3B-40D-2.54R 610-0008-9 40 55.37 48.26 49.53 50.90 ★ HIF3B-50D-2.54R 610-0009-1 50 68.07 60.96 62.23 63.6 ★ HIF3B-60D-2.54R 610-0010-0 60 80.77 73.66 74.93 76.3 ★ HIF3B-64D-2.54R 610-0011-3 64 85.85 78.74 80.01 81.38 The products marked with ★ comply with MIL standard. B18 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Angle Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors contain two types of n=number of contacts ■ polarizing slots. Use products, referring to (Note 1) (Note 2). Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 28.14 ★ HIF3BA-10PA-2.54DS(71) 610-0091-2(71) 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3BD-10PA-2.54DS(71) 610-0171-0(71) 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 33.24 ★ HIF3BA-14PA-2.54DS(71) 610-0092-5(71) 14 37.1 22.6 15.24 26.9 33.0 One on right side MAX56.2 35.74 ★ HIF3BA-16PA-2.54DS(71) 610-0093-8(71) 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BA-20PA-2.54DS(71) 610-0094-0(71) 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 One at center 48.44 ★ HIF3BA-26PA-2.54DS(71) 610-0095-3(71) 26 52.3 37.8 30.48 42.2 48.3 MAX71.4 53.54 ★ HIF3BA-30PA-2.54DS(71) 610-0096-6(71) 30 57.4 42.9 35.56 47.2 53.3 MAX76.5 YES 58.64 ★ HIF3BA-34PA-2.54DS(71) 610-0097-9(71) 34 62.5 48.0 40.64 52.3 58.4 MAX81.6 66.24 ★ HIF3BA-40PA-2.54DS(71) 610-0098-1(71) 40 70.1 55.6 48.26 59.9 66.0 MAX89.2 One on right and 78.94 ★ HIF3BA-50PA-2.54DS(71) 610-0099-4(71) 50 82.8 68.3 60.96 72.6 78.7 One on right and left sides, resp. left sides, resp. MAX101.9 78.94 ★ HIF3BB-50PA-2.54DS(71) 610-0131-5(71) 50 82.8 68.3 60.96 72.6 78.7 One at center MAX101.9 91.64 ★ HIF3BA-60PA-2.54DS(71) 610-0100-1(71) 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 91.64 ★ HIF3BB-60PA-2.54DS(71) 610-0132-8(71) 60 95.5 81.0 73.66 85.3 91.4 One at center MAX114.6 96.74 ★ HIF3BA-64PA-2.54DS(71) 610-0101-4(71) 64 100.6 86.1 78.74 90.4 96.5 One on right and left sides, resp. MAX119.7 96.74 ★ HIF3BB-64PA-2.54DS(71) 610-0133-0(71) 64 100.6 86.1 78.74 90.4 96.5 One at center MAX119.7 The products marked with ★ comply with MIL standard. B19 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four-Wall Straight Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. n=number of contacts ■ Note 4: The 10, 50, 60 and 64 contact connectors contain two types of polarizing slots. Use products, confirming (Note 1) (Note 2). Note 5: The 6 contact has no polarity mark. Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 23.06 ★ HIF3-6PA-2.54DSA(71) 562-0503-9-71 6 26.92 12.42 05.08 16.7 22.82 One at center None MAX46.02 28.14 HIF3BA-10PA-2.54DSA(71) 610-0111-8-71 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 ★ (71) 32.0 17.5 21.8 27.9 HIF3BD-10PA-2.54DSA 610-0181-3-71 10 10.16 None MAX51.1 33.24 ★ (71) 37.1 22.6 26.9 33.0 HIF3BA-14PA-2.54DSA 610-0112-0-71 14 15.24 One on right side MAX56.2 35.74 ★ HIF3BA-16PA-2.54DSA(71) 610-0113-3-71 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BA-20PA-2.54DSA(71) 610-0114-6-71 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 One at center 48.44 ★ HIF3BA-26PA-2.54DSA(71) 610-0115-9-71 26 52.3 37.8 30.48 42.2 48.3 MAX71.4 53.54 ★ HIF3BA-30PA-2.54DSA(71) 610-0116-1-71 30 57.4 42.9 35.56 47.2 53.3 MAX76.5 YES 58.64 ★ (71) 62.5 48.0 52.3 58.4 HIF3BA-34PA-2.54DSA 610-0117-4-71 34 40.64 MAX81.6 66.24 ★ (71) 70.1 55.6 59.9 66.0 HIF3BA-40PA-2.54DSA 610-0118-7-71 40 48.26 MAX89.2 One on right and 78.94 ★ HIF3BA-50PA-2.54DSA(71) 610-0119-0-71 50 82.8 68.3 60.96 72.6 78.7 One on right and left sides, resp. left sides, resp. MAX101.9 78.94 ★ HIF3BB-50PA-2.54DSA(71) 610-0141-9-71 50 82.8 68.3 60.96 72.6 78.7 One at center MAX101.9 91.64 ★ HIF3BA-60PA-2.54DSA(71) 610-0120-9-71 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 91.64 ★ HIF3BB-60PA-2.54DSA(71) 610-0142-1-71 60 95.5 81.0 73.66 85.3 91.4 One at center MAX114.6 96.74 ★ (71) 100.6 86.1 90.4 96.5 HIF3BA-64PA-2.54DSA 610-0121-1-71 64 78.74 One on right and left sides, resp. MAX119.7 96.74 ★ (71) HIF3BB-64PA-2.54DSA 610-0143-4-71 64 100.6 86.1 78.74 90.4 96.5 One at center MAX119.7 The products marked with ★ comply with MIL standard. B20 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Three Wall Angle Type BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves according to the number of contacts. Note 4: The 10 contact connector consists of two types. Use products, confirming (Note 1) (Note 2). n=number of contacts ■ Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 28.14 ★ HIF3BD-10PA-2.54DS(71) 610-0051-8-71 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3BC-10PA-2.54DS(71) 610-0151-2-71 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 35.74 ★ HIF3BD-16PA-2.54DS(71) 610-0052-0-71 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BD-20PA-2.54DS(71) 610-0053-3-71 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 48.44 ★ HIF3BD-26PA-2.54DS(71) 610-0054-6-71 26 52.3 37.8 30.48 42.2 48.3 One at center MAX71.4 53.54 ★ HIF3BD-30PA-2.54DS(71) 610-0055-9-71 30 57.4 42.9 35.56 47.2 53.3 YES MAX76.5 One on right and 58.64 ★ HIF3BD-34PA-2.54DS(71) 610-0056-1-71 34 62.5 48.0 40.64 52.3 58.4 left sides, resp. MAX81.6 66.24 ★ HIF3BD-40PA-2.54DS(71) 610-0057-4-71 40 70.1 55.6 48.26 59.9 66.0 MAX89.2 78.94 ★ HIF3BD-50PA-2.54DS(71) 610-0058-7-71 50 82.8 68.3 60.96 72.6 78.7 MAX101.9 91.64 ★ HIF3BD-60PA-2.54DS(71) 610-0059-0-71 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 96.74 ★ HIF3BD-64PA-2.54DS(71) 610-0060-9-71 64 100.6 86.1 78.74 90.4 96.5 MAX119.7 The products marked with ★ comply with MIL standard. B21 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Three Wall Straight Through hole BPCB mounting pattern Note1,Note2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown n=number of contacts ■ below. Note3: The spacer moves to the right according to the number of contacts. Note4: The 10 contact connector consists of two types. Use products, referring to (Note 1) and (Note 2). Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 28.14 ★ HIF3BD-10PA-2.54DSA(71) 610-0071-5-71 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3BC-10PA-2.54DSA(71) 610-0161-6-71 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 35.74 ★ HIF3BD-16PA-2.54DSA(71) 610-0072-8-71 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BD-20PA-2.54DSA(71) 610-0073-0-71 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 48.44 ★ HIF3BD-26PA-2.54DSA(71) 610-0074-3-71 26 52.3 37.8 30.48 42.2 48.3 One at center MAX71.4 YES 53.54 ★ HIF3BD-30PA-2.54DSA(71) 610-0075-6-71 30 57.4 42.9 35.56 47.2 53.3 MAX76.5 One on right and 58.64 ★ HIF3BD-34PA-2.54DSA(71) 610-0076-9-71 34 62.5 48.0 40.64 52.3 58.4 left sides, resp. MAX81.6 66.24 ★ HIF3BD-40PA-2.54DSA(71) 610-0077-1-71 40 70.1 55.6 48.26 59.9 66.0 MAX89.2 78.94 ★ HIF3BD-50PA-2.54DSA(71) 610-0078-4-71 50 82.8 68.3 60.96 72.6 78.7 MAX101.9 91.64 ★ HIF3BD-60PA-2.54DSA(71) 610-0079-7-71 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 96.74 ★ HIF3BD-64PA-2.54DSA(71) 610-0080-6-71 64 100.6 86.1 78.74 90.4 96.5 MAX119.7 The products marked with ★ comply with MIL standard. B22 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Wrapping Type BPCB mounting pattern Note 1, Note 2. The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3. The spacer moves to the right according to the number of contacts. n=number of contacts ■ Note 4. The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5. The mark * indicates the number of contacts. Note 6. The nut built-in specification product is also provided. The product can be fixed by M2 screws from the rear side. Use the screw of (board thickness) +4 mm under the neck. Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 28.14 ★ HIF3BA-10P-2.54W 610-0503-8 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3BD-10P-2.54W 610-0492-3 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 33.24 ★ HIF3BA-14P-2.54W 610-0493-6 14 37.1 22.6 15.24 26.9 33.0 One on right side MAX56.2 35.74 ★ HIF3BA-16P-2.54W 610-0494-9 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BA-20P-2.54W 610-0495-1 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 One at center 48.44 ★ HIF3BA-26P-2.54W 610-0496-4 26 52.3 37.8 30.48 42.2 48.3 MAX71.4 53.54 ★ HIF3BA-30P-2.54W 610-0497-7 30 57.4 42.9 35.56 47.2 53.3 MAX76.5 YES 58.64 ★ HIF3BA-34P-2.54W 610-0498-0 34 62.5 48.0 40.64 52.3 58.4 MAX81.6 66.24 ★ HIF3BA-40P-2.54W 610-0499-2 40 70.1 55.6 48.26 59.9 66.0 MAX89.2 One on right and 78.94 ★ HIF3BA-50P-2.54W 610-0504-0 50 82.8 68.3 60.96 72.6 78.7 One on right and left sides, resp. left sides, resp. MAX101.9 78.94 ★ HIF3BB-50P-2.54W 610-0500-0 50 82.8 68.3 60.96 72.6 78.7 One at center MAX101.9 91.64 ★ HIF3BA-60P-2.54W 610-0505-3 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 91.64 ★ HIF3BB-60P-2.54W 610-0501-2 60 95.5 81.0 73.66 85.3 91.4 One at center MAX114.6 96.74 ★ HIF3BA-64P-2.54W 610-0506-6 64 100.6 86.1 78.74 90.4 96.5 One on right and left sides, resp. MAX119.7 96.74 ★ HIF3BB-64P-2.54W 610-0502-5 64 100.6 86.1 78.74 90.4 96.5 One at center MAX119.7 The products marked with ★ comply with MIL standard. B23 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Four Wall Straight Through hole [ ] Flux Blister Prevention Type BPCB mounting pattern Note1: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. n=number of contacts ■ Unit:mm Part Number CL No. Number of Contacts A B C D E F Polarizing Slot Polarizing Key Install RoHS 28.14 ★ HIF3CA-10PA-2.54DSA(71) 610-0701-1-71 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3CD-10PA-2.54DSA(71) 610-0722-1-71 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 35.74 ★ HIF3CA-16PA-2.54DSA(71) 610-0703-7-71 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3CA-20PA-2.54DSA(71) 610-0704-0-71 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 48.44 ★ HIF3CA-26PA-2.54DSA(71) 610-0705-2-71 26 52.3 37.8 30.48 42.2 48.3 One at center MAX71.4 53.54 ★ HIF3CA-30PA-2.54DSA(71) 610-0706-5-71 30 57.4 42.9 35.56 47.2 53.3 YES MAX76.5 58.64 ★ HIF3CA-34PA-2.54DSA(71) 610-0707-8-71 34 62.5 48.0 40.64 52.3 58.4 MAX81.6 One on right and 66.24 ★ HIF3CA-40PA-2.54DSA(71) 610-0708-0-71 40 70.1 55.6 48.26 59.9 66.0 left sides, resp. MAX89.2 78.94 ★ HIF3CA-50PA-2.54DSA(71) 610-0709-3-71 50 82.8 68.3 60.96 72.6 78.7 One on right and left sides, resp. MAX101.9 78.94 ★ HIF3CB-50PA-2.54DSA(71) 610-0721-9-71 50 82.8 68.3 60.96 72.6 78.7 MAX101.9 91.64 ★ HIF3CB-60PA-2.54DSA(71) 610-0723-4-71 60 95.5 81.0 73.66 85.3 91.4 One at center MAX114.6 96.74 ★ HIF3CB-64PA-2.54DSA(71) 610-0724-7-71 64 100.6 86.1 78.74 90.4 96.5 MAX119.7 The products marked with ★ comply with MIL standard. B24 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Two Stage Staking Right Angle Through hole Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5: The mark * ndicates the number of contacts. Note 6: The locator is located optionally. Unit:mm Polarizing Slot Polarizing Key Install Part Number CL No. Number of Contacts A B C D E F RoHS (Note 1) (Note 2) 28.14 ★ HIF3BA-10PA-2.54WB(71) 610-1502-0-71 10 32.0 17.5 10.16 21.8 27.9 None One on right side MAX51.1 28.14 HIF3BD-10PA-2.54WB(71) 610-1503-3-71 10 32.0 17.5 10.16 21.8 27.9 None MAX51.1 35.74 ★ HIF3BA-16PA-2.54WB(71) 610-1505-9-71 16 39.6 25.1 17.78 29.5 35.5 MAX58.7 40.84 ★ HIF3BA-20PA-2.54WB(71) 610-1506-1-71 20 44.7 30.2 22.86 34.5 40.6 MAX63.8 48.44 ★ HIF3BA-26PA-2.54WB(71) 610-1507-4-71 26 52.3 37.8 30.48 42.2 48.3 One at center MAX71.4 53.54 ★ HIF3BA-30PA-2.54WB(71) 610-1508-7-71 30 57.4 42.9 35.56 47.2 53.3 MAX76.5 58.64 ★ HIF3BA-34PA-2.54WB(71) 610-1509-0-71 34 62.5 48.0 40.64 52.3 58.4 YES MAX81.6 66.24 ★ HIF3BA-40PA-2.54WB(71) 610-1510-9-71 40 70.1 55.6 48.26 59.9 66.0 MAX89.2 One on right and 78.94 ★ HIF3BA-50PA-2.54WB(71) 610-1511-1-71 50 82.8 68.3 60.96 72.6 78.7 One on right and left sides, resp. left sides, resp. MAX101.9 78.94 ★ HIF3BB-50PA-2.54WB(71) 610-1512-4-71 50 82.8 68.3 60.96 72.6 78.7 One at center MAX101.9 91.64 ★ HIF3BA-60PA-2.54WB(71) 610-1513-7-71 60 95.5 81.0 73.66 85.3 91.4 One on right and left sides, resp. MAX114.6 91.64 ★ HIF3BB-60PA-2.54WB(71) 610-1514-0-71 60 95.5 81.0 73.66 85.3 91.4 One at center MAX114.6 96.74 ★ HIF3BA-64PA-2.54WB(71) 610-1515-2-71 64 100.6 86.1 78.74 90.4 96.5 One on right and left sides, resp. MAX119.7 96.74 ★ HIF3BB-64PA-2.54WB(71) 610-1516-5-71 64 100.6 86.1 78.74 90.4 96.5 One at center MAX119.7 The products marked with ★ comply with MIL standard. B25 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BCombination Pattern Note : Fix the HIF3-mounting hole spacer by screws between upper stage and lower stage connectors. BPCB mounting pattern ■Mounting Hole Spacer Part Number CL No. Finish RoHS HIF-3 mounting hole spacer 562-0714-4 PBT Black YES Note : 2 pieces are contained in a bag. B26 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BPolarizing Key HIF3B-GK CL562-0601-8 HIF3-GPIN(A) HIF3BA-GPIN Note1: One unit of this Note1: One unit of this product is a set of five product is a set of five pieces in conjunction pieces in conjunction with a runner. The unit with a runner. The unit for sale is defined one for sale is defined one pack containing 20 pack containing 20 pieces. pieces. Note2: This product is Note2: This product is applicable to HIF3A- applicable to the *D2.54R, HIF3C- HIF3BA-*D2.54R *D2.54C and product. HIF3BA-*D2.54C products. Part Number CL No. Material Remarks RoHS Part Number CL No. Material Remarks RoHS HIF3-GPIN(A) 562-0126-6 Poly acetal (white) A set of 5 pieces YES HIF3BA-GPIN 612-0500-2 Poly acetal (white) A set of 5 pieces YES B27 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BHIF3-Multi Clamp BHIF3-*CL Pull Tab This clamp is used for intermediate connection in the This pull tab is used for the HIF3 series equipped with cable clamp bus-line system, etc. Remove compulsory force from the function. Remove all compulsory force, which is loaded on the insulation displacement area of the connector in insulation displacement area of the connector for extraction. * Pull Tab can not be used for HIF3BA-*PD. intermediate connection. Note: This HIF3- Note: The pin header corresponds to the HIF3BAE Note: The pin header corresponds to the HIF3BAE series (lock E). series (lock E). BLock ●Low Profile Lock Pin Header ●F Type Lock Pin Header Lock G Lock F Part Number : HIF3BAG-**PA-2.54DSA(71) Part Number : HIF3BAG-**PA-2.54DSA(71) ●Low profile type, and used for lock ejection. ●Locking range more reduced than conventional lock type. Connector height is reduced. Even if connectors are aligned laterally, the mounting Since no connector clamp is needed on the cable side, space is reduced. this is used without turning back on the cable side. Take Note : The clamp must be replaced for HIF3A socket type care about this point. 60 contacts only. Take care about this point. B28 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 21.5 27.3 HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Socket for Crimping Unit: mm Part Number CL No. Number of Contacts A B Polarizing Guide RoHS HIF3BA-10D-2.54C 610-1041-0 10 17.25 10.16 HIF3BA-14D-2.54C 610-1051-3 14 22.35 15.24 HIF3BA-16D-2.54C 610-1042-2 16 24.8 17.78 HIF3BA-20D-2.54C 610-1043-5 20 29.95 22.86 One at center HIF3BA-26D-2.54C 610-1044-8 26 37.55 30.48 HIF3BA-30D-2.54C 610-1045-0 30 42.63 35.56 HIF3BA-34D-2.54C 610-1046-3 34 47.75 40.64 YES HIF3BA-40D-2.54C 610-1047-6 40 55.35 48.26 HIF3BA-50D-2.54C 610-1048-9 One right and left side, resp. 60.96 50 68.04 HIF3BB-50D-2.54C 610-1061-7 One at center HIF3BA-60D-2.54C 610-1049-1 One right and left side, resp. 73.66 60 80.77 HIF3BB-60D-2.54C 610-1062-0 One at center HIF3BA-64D-2.54C 610-1064-5 One right and left side, resp. 78.74 64 85.85 HIF3BB-64D-2.54C 610-1063-2 One at center Note: Some variations may differ from those in above figures. B29 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Cover Case for Crimping socket Unit: mm Part Number CL No. Number of Contacts A B C D E RoHS HIF3-20CV(71) 562-0201-0-71 20 24.5 18.0 12.0 30.5 29.95 HIF3-26CV(71) 562-0202-2-71 26 30.2 20.0 14.0 32.0 37.55 HIF3-30CV(71) 562-0203-5-71 30 32.2 22.0 16.0 33.0 42.63 HIF3-34CV(71) 562-0204-8-71 34 34.2 24.0 18.0 33.5 47.75 YES HIF3-40CV(71) 562-0205-0-71 40 36.2 26.0 20.0 35.5 55.35 HIF3-50CV(71) 562-0206-3-71 50 39.2 29.0 23.0 38.0 68.04 HIF3-60CV(71) 562-0207-6-71 60 42.2 32.0 26.0 40.5 80.77 Note 1: The type F lock pin header cannot be used for a mating member. Note 2: Note that the product cannot be used with AWG #20. Applicable jacket diameters are as described below. 20 contacts: 1.7 mm diameter MAX 26 to 40 contacts: 1.6 mm diameter MAX 50 to 60 contacts: 1.4 mm diameter MAX B30 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Contact for Crimping Socket RoHS RoHS RoHS gold plated contact in bag gold plated contact in bag gold plated contact in bag HIF3-2226SC 562-0079-8 HIF3-2428SC 562-0124-0 HIF3-2022SC 562-0492-4 YES YES YES Selective gold plated contact in bag Selective gold plated contact in bag AWG#20 to #22 UL 1007 Stranded wire HIF3-2226SCA 562-0244-2 HIF3-2428SCA 562-0246-8 Applicable cable AWG#22 to #26 UL 1007 Stranded wire AWG#24 to #28 UL 1007 Stranded wire HIF3-TA2022HC Applicable cable Applicable cable Manual crimping tool HIF3-T2226HC HIF3-TA2428HC Manual crimping tool Manual crimping tool RoHS RoHS RoHS HIF3-2226SCF 562-0080-7 gold plated contact in reel HIF3-2428SCF 562-0125-3 gold plated contact in reel HIF3-2022SCF 562-0493-7 gold plated contact in reel YES YES YES ** HIF3-2226SCFA 562-0245-5 Selective gold plated contact in reel HIF3-2428SCFA 562-0247-0 Selective gold plated contact in reel Applicable cable AWG#20 to #22 UL 1007 Stranded wire Applicable cable AWG#22 to #26 UL 1007 Stranded wire Applicable cable AWG#24 to #28 UL 1007 Stranded wire Note:* products have both side careers. Type VA (Selective gold plated in reel) Part Number CL No. Applicable Cable RoHS A B C D E F 11.5 0.8 1.8 1.8 2.3 2.6 HIF3-2226SCFC 613-0002-1 AWG#22 to #26 UL 1007 Stranded wire 11.5 0.8 1.4 1.35 2.0 2.1 YES HIF3-2630SCFC 613-0001-9 AWG#26 to #30 UL 1007 Stranded wire 12.4 1.7 1.1 1.1 1.4 1.5 HIF3A-3236SCFC 613-0005-0 AWG#32 to #36 UL 1007 Stranded wire Type VA (Selective gold plated contact in bag) Part Number CL No. Applicable Cable Manual Crimp Tool RoHS A B C D E F HIF3-2226SCC 613-0004-7 AWG#22 to #26 UL 1007 Stranded wire HIF3-TB2226HC 11.5 0.8 1.8 1.8 2.3 2.6 YES HIF3-2630SCC 613-0003-4 AWG#26 to #30 UL 1007 Stranded wire HIF3-TB2630HC 11.5 0.8 1.4 1.35 2.0 2.1 B31 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BTools ●Crimping Tool Part Number CL No. HIF3-T2226HC 550-0063-8 Manual Crimping Tool HIF3-T2226HC ●Automatic Crimping Tool (Type: CM-105) Part Number CL No. CM-105 901-0005-4 ●Contact Extraction Tools How to use the extraction tool (2) How to adjust the lance (raise) (1) How to extract contacts In order to re-insert the contact As shown in Figure 1, where the removed from the insulated case, extraction tool is inserted in the lance raise the contact lance area using the fixed slot on the insulated case, slightly tool A, and re-insert the contact, as pull the cable, and the contact can be shown in Figure 2. removed. Part Number CL No. HIF1-PO 550-0049-7 Figure 1 B32 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Part Number CL No. Applicable Contact Applicable Cable Type Item Manual Manual crimping tool HIF3-2226SC HIF3-T2226HC 550-0063-8 AWG#22 to #26 HIF3-2226SCA HIF3-2428SC HIF3-TA2428HC 550-0100-2 AWG#24 to #28 HIF3-2428SCA HIF3-TA2022HC 550-0124-0 HIF3-2022SC AWG#20 to #22 HIF3-TB2226HC 550-0154-1 AWG#22 to #26 HIF3-2226SCC HIF3-TB2630HC 550-0155-4 AWG#26 to #30 HIF3-2630SCC Automatic Automatic crimping tool unit CM-105 901-0005-4 ––––––– ––––––– AWG#22 to #26 HIF3-2226SCF Applicator AP105-HIF3-22-28SCF 901-4031-6 HIF3-2428SCF AWG#24 to #28 ( ) Note1 HIF3-2226SCFA AWG#22 to #26 AP105-HIF3-22-28SCFA 901-4030-3 HIF3-2428SCFA ( ) AWG#24 to #28 Note1 AP105-HIF3-2022S 901-4027-9 HIF3-2022SCF AWG#20 to #22 AP105-HIF3-2226SCFC 901-4005-6 HIF3-2226SCFC AWG#22 to #26 AP105-HIF3-2630SCFC 901-4006-9 HIF3-2630SCFC AWG#26 to #30 AP105-HIF3-3236SCFC 901-4007-1 HIF3-3236SCFC AWG#32 to #36 Extraction tool HIF1-PO 550-0049-7 ––––––– ––––––– Note1: AP106-HIF3-22-28SCF and AP105-HIF3-22-28CFA can be modified by changing a few parts. B33 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BSocket Side (Crimping) Assembling Procedures (1) As shown in Figure 1, peel the applicable cable (AWG#20 to #26) jacket, and connect it using crimping jig HIF3-TA2022HC, HIF3-TA2226HC, or HIF3-TA2426HC. In this case, insert the cable so as to hit the contact cable stripper position as shown Figure 2. (2) After connection as shown Figure 2, check the contact direction, and insert the contact as shown Figures 3 and 4. Slightly pull the cable, and check whether the contact lance position is firmly fixed to the insulation case, as shown in the area (A). Note1 : For handling procedures for special crimping tools, refer to the "Handling Instruction Manual". Note2 : Wire strip length: Refer to crimp condition sheet. Wire strip length Figure 1 Figure 2 Figure 3 Figure 4 B34 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF3B Connection Circuit Diagram Type AB Type AD Type CD B35 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Type CD Type AD Type AB HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type AC Type CC Type AA B36 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Type AA Type CC Type AC HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF2E R(S) A to HIF3B Connection Circuit Diagram Type AA Type AC B37 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type BA Type BC B38 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF2E R(S)B to HIF3 Connection Circuit Diagram Type AA Type AC B39 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard Type BA Type BC B40 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard HIF3B In-line Type Ribbon Cable Connector ■Features 1. In-line Type This connector can be used for internal wiring cable to cable within equipment. 2. Compatibility This connector is compatible with HIF3A series as well as HIF3B series socket. 3. Applicable Cable The applicable cable is UL2651 AWG#28 flat cable (7 pcs./6.127mm, jacket diameter: 0.8 to 1.0mm). ■Product Specifications Current rating : 1A Operating Temperature Range : –55 to +85ç (Note 1) Storage Temperature Range : –10 to +60ç (Note 2) Rating Voltage rating : 200V AC Operating Moisture Range : 40 to 80% Storage Humidity Range : 40 to 70% (Note 2) Item Specification Condition 1. Insulation Resistance 1000M ohms min. 500V DC 2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute 3. Contact Resistance 15m ohms max. 0.1A 4. Vibration No electrical discontinuity of 1μs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 1000M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% (-65ç: 30 minutes ➝ 15 to 35ç: 5 minutes max. 6. Temperature Cycle No damage, cracks, or parts looseness. 125ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 15m ohms max. 500 cycles Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Material Part Material Finish Remarks Insulator PBT Black UL94V-0 Plug Contact Beryllium copper Gold plated over nickel underplated –––––– ■Ordering Information HIF3BA - * * P D - 2.54 R - MC qe w r t y u q Series Name : HIF3BB (50, 60, 64 contacts only) e P : Plug HIF3BD (10 contacts only) r D : contact alignment : D : Double HIF3BAE (60 contacts only) t Contact Pitch : 2.54mm w Number of Contacts : 10, 16, 20, 26, 30, 34, 40, 50, 60 y Connection type : Ribbon cable and 64 u MC : Mold clamp B41 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard ■Plug Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. The 10 contact connector only has no position for polarizing key insulation. Note 3: The number indicated in parentheses are sizes for 60 and 64 contact connectors. Note 4: The HIF3BAE-60PD-2.54R-MC product partially differs in a locking form, and the mating member is applicable for HIF3A only. Unit:mm Part Number CL No. Number of Contacts A B C D E F G H Polarizing slot RoHS 28.14 HIF3BDE-10PD-2.54R-MC 611-0031-7 10 31.98 17.48 10.16 21.88 30.13 MAX51.1 35.74 HIF3BAE-16PD-2.54R-MC 611-0032-0 16 39.60 25.10 17.78 29.50 37.75 MAX58.7 40.84 HIF3BAE-20PD-2.54R-MC 611-0033-2 20 44.68 30.18 22.86 34.58 42.83 MAX63.8 48.44 HIF3BAE-26PD-2.54R-MC 611-0034-5 26 52.30 37.80 30.48 42.20 50.45 One at center MAX71.4 53.54 HIF3BAE-30PD-2.54R-MC 611-0035-8 30 57.38 42.88 35.56 47.28 55.53 33.2 MAX76.5 58.64 HIF3BAE-34PD-2.54R-MC 611-0036-0 34 62.46 47.96 40.64 52.36 60.61 29.2 MAX81.6 66.24 HIF3BAE-40PD-2.54R-MC 611-0037-3 40 70.08 55.58 48.26 59.98 68.23 MAX89.2 YES 78.94 HIF3BAE-50PD-2.54R-MC 611-0038-6 50 One on right and left sides, resp. 82.78 68.28 60.96 72.68 80.93 HIF3BBE-50PD-2.54R-MC 611-0041-0 50 MAX101.9 One at center HIF3BAE-60PD-2.54R-MC 611-0039-9 60 91.64 One on right and left sides, resp. 35.2 MAX114.6 HIF3BBE-60PD-2.54R-MC 611-0042-3 60 95.48 80.98 73.66 85.38 93.63 One at center 91.7 HIF3BAE-60PD-2.54R-MC 611-0059-6 60 31.2 37.2 MAX121.3 One on right and left sides, resp. 96.74 HIF3BAE-64PD-2.54R-MC 611-0040-8 64 100.56 86.06 78.74 90.46 98.71 29.2 35.2 MAX119.7 HIF3BBE-64PD-2.54R-MC 611-0045-1 64 One at center locking size *D size unlocking size B42 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. HIF3B Series●Ribbon Cable connector Compliant with MIL Standard BConnection Procedures +10 Note1: Cable length tolerance Less than 500 (mm) Note2: When a cable such as a twist cable +00 +3 More than 500 (mm) or a slit (like a roller screen) cable is +0 used, the cable pitch will change according to cable manufacturers. If connection failure has occurred, please contact Hirose sales. Type AO Type BO Type CO Type DO B43 Powered by TCPDF (www.tcpdf.org) Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved.