17mm 0.5 mm Pitch, 0.9 mm Height, FPC/FFC Connectors FH19C Series/FH19SC Series FH19C – FPC/FFC thickness: 0.2±0.03mm Actuator color: Brown FH19SC – FPC/FFC thickness: 0.3±0.03mm Actuator color: Black ● 0.9mm high (30 pos. shown) ■Features 1. Low-profile 0.5mm pitch FPC/FFC Connectors Miniaturization of portable equipment and personal mobile devices has created increased demand for a low 0.9mm profile, high density, and high reliability connectors. *The design of this connector has been made thinner and smaller, with a height of 0.9mm and width of 3mm. *PCB footprint: Reduced approximately 48% (as compared with Hirose Electric's 0.5mm pitch FH12 Series connectors) ● Can be mounted over conductive traces *Connector weight: Reduced approximately 78% (as compared with Hirose Electric's 0.5mm pitch FH12 Series connectors) 2. Conductive traces on the PCB can run under the connector All bottom surface of the connector is solid, without any exposure of the contact. 3. Proven Flip-Lock Actuator System assures Enclosed construction easy and reliable operation (No exposed contacts) Rotating actuator permits easy insertion and reliable Metal fittings connection with the FPC & FFC. (Leadless) Tactile sensation confirms complete mechanical locking of the actuator and the electrical connection. ● Metal Fittings (Leadless Type) 4. Accepts 0.2mm & 0.3mm thick FPC/FFC No protrusions on No exposed contacts on the bottom of the connector. the sides allows The connector will also terminate with 0.2mm thick Flat close side-by-side Flexible Cable (FFC). board placement. 5. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging ● Actuator Temporary Hold Mechanism contains 5000 connectors. 6. Wide range of contact counts The contact positions available range from 4 to 50. 7. Satisfies Halogen-free requirements All materials and substances used in this product comply with the Halogen-free standards. * Defined according to IEC61249-2-21 Br: 900ppm max, Cl: 900ppm max, Br+Cl: 1,500ppm max Actuator stays open during insertion of the FPC/FFC. 1 2013.11w 3mm Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Product Specifications Operating temperature range Storage temperature range ( ) Note1 Current rating 0.5 A + + -55ç to 85ç (Note 2) -10ç to 50ç (Note 3) Rating Operating humidity range Storage humidity range Voltage rating 50 V AC Relative humidity 90% max. (No condensation) Relative humidity 90% max. (No condensation) Thickness: = 0.2 ± 0.03mm Gold plated Recommended FH19C Series FPC, FFC FH19SC Series Thickness: = 0.3 ± 0.03mm Gold plated Item Specification Conditions 1. Insulation resistance 500 M ohms min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown 150 V AC/1 minute 100 m ohms max. 3. Contact resistance 1 mA *Including FPC/FFC conductor resistance 4. Durability Contact resistance: 100 m ohms max. 20 cycles (insertion/ withdrawal) No damage, cracks, or parts dislocation. No electrical discontinuity of 1 μs or more. Frequency: 10 to 55 Hz, single amplitude of 5. Vibration Contact resistance: 100 m ohms max. 0.75mm, 10 cycles in each of the 3 directions No damage, cracks, or parts dislocation. No electrical discontinuity of 1 μs. min. 2 Acceleration of 981 m/s , 6 ms duration, sine half- 6. Shock Contact resistance: 100 m ohms max. wave waveform, 3 cycles in each of the 3 axis. No damage, cracks, or parts dislocation. Contact resistance: 100 m ohms max. 96 hours at temperature of 40ç and humidity of 7. Humidity Insulation resistance: 100 M ohms min. 90 to 95% (Steady state) No damage, cracks, or parts dislocation. + + + + + Contact resistance: 100 m ohms max. Temperature: -55ç 15ç to 35ç 85ç 15ç to 35ç / / / + Time : -30 2 to 3 30 2 to 3(Minutes) 8. Temperature cycle Insulation resistance: 100 M ohms min. / / / No damage, cracks, or parts dislocation. 5 cycles 9. Resistance to Reflow: At the recommended temperature profile No deformation of components affecting performance. soldering heat Manual soldering: 350ç±5ç for 5 seconds Note 1: When passing the current through all of the contacts, use 70% of the current rating. Note 2: Includes temperature rise caused by current flow. Note 3: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.Information ■Materials Part Material Finish Remarks Color: Beige Color: Brown (FH19C Series) Insulator LCP UL94V-0 Color: Black (FH19SC Series) Contacts Phosphor bronze Gold plated ------- Metal fittings Phosphor bronze Pure tin reflow plated ------- ■Ordering information FH 19 C - 30S - 0.5 SH (05) 1 2 3 4 5 6 7 1 Series name : FH 5 Contact pitch : 0.5mm 2 Series No. : 19 6 Terminal type SH: SMT horizontal mounting type 3 C: FPC thickness : 0.2mm SC : FPC/FFC thickness : 0.3mm Material and plating specifications : 7 FH19C : (10)...Gold plating with nickel barrier 5,000pieces/reel 4 No. of contacts : 4 to 50 (99)...Gold plating with nickel barrier 500pieces/reel FH19SC : (09)...Gold plating with nickel barrier 5,000pieces/reel (99)...Gold plating with nickel barrier 500pieces/reel 2 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Connector Dimension [FH19C Series] A±0.15 B G ∞Number of contacts 0.5 (0.15) 0.15 G A (130°) Polarizing mark indicator Number of contacts indicator (0.15) (C: FPC insertion slot dimension) 2 1 0.15MAX 0.15MAX 12 D±0.1 (1.3) S 2.15±0.2 Notes 1 The coplanarity of each terminal lead and metal fitting is within 0.1mm. 2 The contact terminal lead position indicates the dimension from the bottom surface of the insulator body. 3 Difference between terminal contact to be max. 0.1mm. 4 Packaged on tape and reel only. Check packaging specification. 5 Any discoloration of the plastic compound will NOT AFFECT form, fit or function of the connector. 6 After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit: mm Part Number CL No. Number of Contacts A B C D FH19C-04S-0.5SH(**) 580-0410-1-** 4 4 1.5 2.57 3.35 FH19C-05S-0.5SH(**) 580-0418-3-** 5 4.5 2 3.07 3.85 FH19C-06S-0.5SH(**) 580-0409-2-** 6 5 2.5 3.57 4.35 FH19C-07S-0.5SH(**) 580-0411-4-** 7 5.5 3 4.07 4.85 FH19C-08S-0.5SH(**) 580-0404-9-** 8 6 3.5 4.57 5.35 FH19C-09S-0.5SH(**) 580-0403-6-** 9 6.5 4 5.07 5.85 FH19C-10S-0.5SH(**) 580-0412-7-** 10 7 4.5 5.57 6.35 FH19C-12S-0.5SH(**) 580-0413-0-** 12 8 5.5 6.57 7.35 FH19C-13S-0.5SH(**) 580-0405-1-** 13 8.5 6 7.07 7.85 FH19C-15S-0.5SH(**) 580-0406-4-** 15 9.5 7 8.07 8.85 FH19C-17S-0.5SH(**) 580-0408-0-** 17 10.5 8 9.07 9.85 FH19C-20S-0.5SH(**) 580-0402-3-** 20 12 9.5 10.57 11.35 FH19C-21S-0.5SH(**) 580-0414-2-** 21 12.5 10 11.07 11.85 FH19C-24S-0.5SH(**) 580-0407-7-** 24 14 11.5 12.57 13.35 FH19C-27S-0.5SH(**) 580-0401-0-** 27 15.5 13 14.07 14.85 FH19C-30S-0.5SH(**) 580-0400-8-** 30 17 14.5 15.57 16.35 FH19C-34S-0.5SH(**) 580-0419-6-** 34 19 16.5 17.57 18.35 FH19C-40S-0.5SH(**) 580-0416-8-** 40 22 19.5 20.57 21.35 FH19C-50S-0.5SH(**) 580-0417-0-** 50 27 24.5 25.57 26.35 Note1: Embossed tape reel packaging (5,000 pieces/reel, 500 pieces/reel). Order by number of reels. 3 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. (1) +0.15 0.5 3 (0.5) 2.5±0.15 0 (1.6) 0.9±0.1(Including contact terminal leads) FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors [FH19SC Series] A±0.15 B G ∞Number of contacts 0.5 (0.15) 0.15 G A 5 (130°) Polarizing mark indicator Number of contacts indicator (0.15) (C: FPC insertion slot dimension) 2 1 0.15MAX 0.15MAX 12 D±0.1 (1.3) S 2.15±0.2 Notes 1 The coplanarity of each terminal lead and metal fitting is within 0.1mm. 2 The contact terminal lead position indicates the dimension from the bottom surface of the insulator body. 3 Difference between terminal contact to be max. 0.1mm. 4 Any discoloration of the plastic compound will NOT AFFECT form, fit or function of the connector. 5 The contacts are protruding. 0.03mm max. from the housing top surface. 6 Packaged on tape and reel only. Check packaging specification. 7 After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit: mm Part Number CL No. Number of Contacts A B C D FH19SC-12S-0.5SH(**) 580-0512-1-** 12 8 5.5 6.57 7.35 FH19SC-13S-0.5SH(**) 580-0518-8-** 13 8.5 6 7.07 7.85 FH19SC-14S-0.5SH(**) 580-0509-7-** 14 9 6.5 7.57 8.35 FH19SC-15S-0.5SH(**) 580-0503-0-** 15 9.5 7 8.07 8.85 FH19SC-16S-0.5SH(**) 580-0521-2-** 16 10 7.5 8.57 9.35 FH19SC-17S-0.5SH(**) 580-0504-3-** 17 10.5 8 9.07 9.85 FH19SC-18S-0.5SH(**) 580-0519-0-** 18 11 8.5 9.57 10.35 FH19SC-20S-0.5SH(**) 580-0502-8-** 20 12 9.5 10.57 11.35 FH19SC-21S-0.5SH(**) 580-0505-6-** 21 12.5 10 11.07 11.85 FH19SC-22S-0.5SH(**) 580-0506-9-** 22 13 10.5 11.57 12.35 FH19SC-24S-0.5SH(**) 580-0511-9-** 24 14 11.5 12.57 13.35 FH19SC-26S-0.5SH(**) 580-0510-6-** 26 15 12.5 13.57 14.35 FH19SC-27S-0.5SH(**) 580-0516-2-** 27 15.5 13 14.07 14.85 FH19SC-28S-0.5SH(**) 580-0513-4-** 28 16 13.5 14.57 15.35 FH19SC-30S-0.5SH(**) 580-0500-2-** 30 17 14.5 15.57 16.35 FH19SC-32S-0.5SH(**) 580-0514-7-** 32 18 15.5 16.57 17.35 Note1: Embossed tape reel packaging (5,000 pieces/reel, 500pieces/reel) . Order by number of reels. 4 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. (1) +0.15 0.5 3 0 (0.5) 2.5±0.15 (1.6) 0.93±0.1(Including contact terminal leads) FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended PCB Land and Metal Mask Dimensions [Common to FH19C & FH19SC Series] Recommended metal mask thickness: 0.10 mm. B H ∞Number of contacts 0.3±0.05 (Land) 0.5 0.1 H 0.25±0.05 (Metal mask) (0.05) J±0.1 (0.2) K±0.1 (A) ■Recommended FPC, FFC Dimensions [Common to FH19C & FH19SC Series] L±0.05 0.5±0.07 B±0.03 FH19C Series FH19SC Series 0.35±0.03(FPC) 0.5±0.03 0.2±0.03 0.3±0.03 0.3±0.03(FFC) Note 1: Stiffener dimension should be 3.5mm min., and X dimension should be 0.5mm for improved flexibility of FPC. Unit: mm Unit: mm Number of Contacts A B J K L Number of Contacts A B J K L 4 4.0 1.5 3.1 3.9 2.5 20 12.0 9.5 11.1 11.9 10.5 5 4.5 2.0 3.6 4.4 3.0 21 12.5 10.0 11.6 12.4 11.0 6 5.0 2.5 4.1 4.9 3.5 22 13.0 10.5 12.1 12.9 11.5 7 5.5 3.0 4.6 5.4 4.0 24 14.0 11.5 13.1 13.9 12.5 8 6.0 3.5 5.1 5.9 4.5 26 15.0 12.5 14.1 14.9 13.5 9 6.5 4.0 5.6 6.4 5.0 27 15.5 13.0 14.6 15.4 14.0 10 7.0 4.5 6.1 6.9 5.5 28 16.0 13.5 15.1 15.9 14.5 12 8.0 5.5 7.1 7.9 6.5 30 17.0 14.5 16.1 16.9 15.5 13 8.5 6.0 7.6 8.4 7.0 32 18.0 15.5 17.1 17.9 16.5 14 9.0 6.5 8.1 8.9 7.5 34 19.0 16.5 18.1 18.9 17.5 15 9.5 7.0 8.6 9.4 8.0 40 22.0 19.5 21.1 21.9 20.5 16 10.0 7.5 9.1 9.9 8.5 45 24.5 22.0 23.6 24.4 23.0 17 10.5 8.0 9.6 10.4 9.0 50 27.0 24.5 26.1 26.9 25.5 18 11.0 8.5 10.1 10.9 9.5 5 2-R0.2 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 2.5±0.3 (Exposed traces) 3.3±0.05 0.8±0.05 0.8±0.05 (X) 3.5 min. (Stiffener) (0.15) (0.15) (2.5) (0.15) (3) (0.15) 3.5 min. (Stiffener) FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■FH19C & FH19SC Series FPC/FFC Construction (Recommended Specifications) FPC : Flexible Printed Circuit 1. Using Single-sided FPC Thickness (μm) Material Name Material FH19C FH19SC Covering layer film Polyimide 1 mil thick (25) (25) Cover adhesive (25) (25) Nickel under plated 1 to 5μm / Surface treatment 3 3 Gold plated 0.2μm Copper foil Cu 1oz 35 35 Base adhesive Thermosetting adhesive 25 25 Base film Polyimide 1 mil thick 25 25 Reinforcement material adhesive Thermosetting adhesive 30 30 Polyimide FH19C:3mil Stiffener 75 175 FH19SC:7mil Total 193 293 FPC : Flexible Printed Circuit 2. Using Double-sided FPC Thickness (μm) Material Name Material FH19C FH19SC (25) (25) Covering layer film Polyimide 1 mil thick Cover adhesive (25) (25) Nickel under plated 1 to 5μm / Surface treatment 3 3 Gold plated 0.2μm Through-hole copper Cu 15 15 Copper foil Cu 1/2oz 18 18 Base adhesive Thermosetting adhesive 18 18 Base film Polyimide 1 mil thick 25 25 Base adhesive 18 18 18 18 Copper foil Cu 1/2oz 25 25 Cover adhesive Thermosetting adhesive 25 25 Covering layer film Polyimide 1 mil thick 25 50 Reinforcement material adhesive Thermosetting adhesive Polyimide FH19C:1mil 25 100 Stiffener FH19SC:4mil Total 197 297 FFC : Flexible Flat Cable 3. Using FFC (Flexible Flat Cable) Thickness (μm) Material Name Material FH19C FH19SC (12) (12) Polyester film Adhesive Polyester thermoplastic type (30) (30) 35 35 (Nickel under plated / Gold plated), soft copper film 30 30 Adhesive Polyester 12 12 Polyester 30 30 Adhesive Polyester Stiffener Polyester 100 188 Total 207 295 * Practical tolerance of thickness dimension is ±20μm (i.e., 187 to 227μm). 1. This specification is a recommendation for the construction of the 4. Precautions FH19C/FH19SC Series FPC and FFC (t=0.2/0.3±0.03). 2. For details about the construction, please contact the FPC/FFC manufacturers. 6 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Packaging Specifications [Common to FH19C & FH19SC Series] ● Embossed Carrier Tape Dimensions (1.7) 4±0.1 2±0.15 8±0.1 (0.3) (3.3) Flat surface for placement with automatic equipment (4.3) Unreeling direction (1) ●Reel Dimensions (R:INSIDE) (T:OUTSIDE) End cection Mounting cection Lead cection (400 mm min.) Embossed carrier tape Blank cection Blank cection Top cover tape (10 pockets min.) (10 pockets min.) Unit: mm Unit: mm Number of Contacts M N Q R T Number of Contacts M N Q R T 4 16 7.5 4.3 17.4 21.4 20 24 11.5 12.3 25.4 29.4 5 16 7.5 4.8 17.4 21.4 21 24 11.5 12.8 25.4 29.4 6 16 7.5 5.3 17.4 21.4 22 24 11.5 13.3 25.4 29.4 7 16 7.5 5.8 17.4 21.4 24 24 11.5 14.3 25.4 29.4 8 16 7.5 6.3 17.4 21.4 26 24 11.5 15.3 25.4 29.4 9 16 7.5 6.8 17.4 21.4 27 24 11.5 15.8 25.4 29.4 10 16 7.5 7.3 17.4 21.4 28 24 11.5 16.3 25.4 29.4 12 16 7.5 8.3 17.4 21.4 30 24 11.5 17.3 25.4 29.4 13 16 7.5 8.8 17.4 21.4 32 32 14.2 18.3 33.4 37.4 14 16 7.5 9.3 17.4 21.4 34 32 14.2 19.3 33.4 37.4 15 16 7.5 9.8 17.4 21.4 40 44 20.2 22.3 45.4 49.4 16 24 11.5 10.3 25.4 29.4 45 44 20.2 24.8 45.4 49.4 17 24 11.5 10.8 25.4 29.4 50 44 20.2 27.3 45.4 49.4 18 24 11.5 11.3 25.4 29.4 Note: Embossed tape 32 mm or wider will have perforated feed holes on two sides. 7 +0.1 Ø1.5 0 (Ø13) Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. (Ø380) (Ø80) (Q) N±0.1 1.75±0.1 M±0.3 FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended Temperature Profile [For FH19C & FH19SC Series] MAX 250ç HRS test condition Solder method :Reflow, IR/hot air 250 Solder composition :Paste, 230ç 96.5%Sn/3.0%Ag/0.5%Cu 200 200ç (Senju Metal Industry, Co., Ltd.’s Part Number:M705-221CM5-32- 150 150ç 10.5) Test board :Glass epoxy 45mm∞100mm∞1.6mm thick 100 Land dimensions :0.3mm∞0.8mm Metal mask :0.25mm∞0.8mm∞0.1mm 50 This temperature profile is based on the above 25ç (60 sec.) 90 sec. to 120 sec. (60 sec.) conditions. 0 In individual applications the actual temperature may Start Preheating Soldering vary, depending on solder paste type, Time (Seconds) volume/thickness and board size/thickness. Consult tour solder paste and equipment manufacturer for specific recommendations. 8 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Temperature(ç) FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Connector Operation and Precautions Operation Precautions 1) Do not apply excessive force or use any type 1. FPC/FFC Termination procedure. of tool to operate the actuator. Connector installed on the board. 1) Lift up the actuator. Use thumb or index fin- ger. 2) The connector will assure reliable performance when the actuator is open to 130° maximum. Do not exceed this angle, as this may cause permanent damage to the connector. 2) Assure that the FPC/FFC is fully inserted parallel to mounting surface, with the exposed conductive traces facing down. FPC conductor surface 3) Insert the FPC/FFC straight into the insertion open- (Bottom side) ing. Failing to follow this precaution can lead to damaging the FPC/FFC and altering its connectivity. 3) Rotate down the actuator until firmly closed. It is critical that the inserted FPC/FFC is not moved and remains fully inserted. Should the FPC/FFC be moved, open the actuator and repeat the process, starting with Step 1 above. 4) When you insert the FPC into the insertion open- ing, do not apply excessive pressure or scrape the FPC on the bottom of the opening. Doing so can lead to deformities of the contacts and can hinder the performance of the connector. 2. FPC/FFC Removal 1) Lift up the actuator. 2) Carefully remove the FPC/FFC. 5) Application of excessive force to the inserted FPC/FFC may cause damage to connector and may affect the reliability of electrical con- nection. If specific applica- tion requires con- tinuous or repeated pull or bend of the inserted FPC/FFC, assure that the forces are NOT transmitted directly to the connector. 9 FPC·FFC insertion opening Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors : NOTES 10 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors : NOTES 11 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH19C & FH19SC Series●0.5mm pitch, 0.9mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors USA: USA: USA: HIROSE ELECTRIC (U.S.A.), INC. Headquarters HIROSE ELECTRIC (U.S.A.), INC. North California Office HIROSE ELECTRIC (U.S.A.), INC. Detroit Office (Automotive) 2688 Westhills Court, Simi Valley, CA 93065-6235 20400 Stevens Creek Blvd., Ste 250, Cupertino, CA 37677 Professional Center Drive, Suite #100C Phone : 1-805-522-7958 95014 Livonia, MI 48154 Fax : 1-805-522-3217 Phone : 1-408-253-9640 Phone : 1-734-542-9963 http://www.hiroseusa.com Fax : 1-408-253-9641 Fax : 1-734-542-9964 http://www.hiroseusa.com http://www.hiroseusa.com GERMANY: THE NETHERLANDS: UK: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH HIROSE ELECTRIC EUROPE B.V. HIROSE ELECTRIC EUROPE B.V. UK BRANCH Herzog-Carl-Strasse 4 D-73760 Ostfildern Hogehillweg #8 1101 CC Amsterdam Z-O First Floor, St Andrews House, Caldecotte Lake (Scharnhauser Park) Phone : 31-20-6557460 Business Park, Milton Keynes MK7 8LE Phone : 49-711-4560-02-1 Fax : 31-20-6557469 Phone : 44-1908-369060 Fax : 49-711-4560-02-299 http://www.hiroseeurope.com Fax : 44-1908-369078 http://www.hirose.de http://www.hirose.co.uk CHINA: CHINA: CHINA: HIROSE ELECTRIC CO., LTD. BEIJING REPRESENTATIVE OFFICE HIROSE ELECTRIC (SHANGHAI) CO., LTD. HIROSE ELECTRIC CO., LTD. SHENZHEN OFFICE A1001, Ocean International Center, Building 56# East 4th 1501-02, Cross Tower Building, 318 Fuzhou Road, Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre Ring Middle Road, Chao Yang District, Beijing, 100025 Huang Pu District, Shanghai 200001 5002, ShenNanDong Road, ShenZhen City, Guangdong Province, 518008 Phone : 86-10-5165-9332 Phone : 86-21-6391-3355 Phone : 86-755-8207-0851 Fax : 86-10-5908-1381 Fax : 86-21-6335-0767 Fax : 86-755-8207-0873 http://www.hirose-china.com.cn http://www.hirose-china.com.cn http://www.hirose-china.com.cn HONG KONG: TAIWAN: SINGAPORE: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. HIROSE ELECTRIC TAIWAN CO., LTD. HIROSE ELECTRIC CO., LTD. Unit 1102 A&B, Energy Plaza, 92 Granville Road, 103 8F, No.87, Zhengzhou Rd., Taipei 10 Anson Road #26-16 International Plaza 079903 Tsim Sha Tsui East, Kowloon Phone : 886-2-2555-7377 Phone : 65-6324-6113 Phone : 852-2803-5338 Fax : 886-2-2555-7350 Fax : 65-6324-6123 http://www.hirose-singapore.com.sg Fax : 852-2591-6560 http://www.hirose-taiwan.com.tw http://www.hirose-hongkong.com.hk KOREA: HIROSE KOREA CO., LTD. 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do 429-450 Phone : 82-31-496-7000,7124 Fax : 82-31-496-7100 http://www.hirose.co.kr ® 6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN + + TEL: 81-45-620-3526 Fax: 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The contents of this catalog are current as of date of 11/2013. Contents are subject to change without notice for the purpose of improvements. 12 Powered by TCPDF (www.tcpdf.org) Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved.