0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors FH30 Series Strong actuator construction Enclosed shaft of the actuator prevents it from dislocation Simple FPC insertion ■Features 1. Strong actuator retention Actuator will not be dislodged when operating under harsh conditions. 2. Rotating Flip–Lock actuator Rotating actuator permits easy insertion and retention of the FPC. Tactile sensation confirms complete FPC insertion and reliable mechanical and electrical connection. 3. FPC position hold Tabs on each side of the FPC assure correct placement and hold in the connector prior to closing of the actuator. FPC positioning tab 4. Accepts standard FPC thickness 0.3mm thick standard Flexible Printed Circuit (FPC) can be Lock used. 5. Easy solderability on the PC board The soldering leads are on 0.6 mm or 0.8 mm pitch, exiting on the front and back of the connector. 6. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 1000 connectors. 7. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. * 8. Halogen-free * As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 1 2013.11w Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Product Specifications 0.3 mm pitch 0.4 mm pitch Operating temperature range -40 to +85°C (Note 2) Storage temperature range -10 to +50°C (Note 3) Ratings Current rating(Note 1) 0.15 A 0.3 A Operating humidity range Relative humidity 90% max. Storage humidity range Relative humidity 90% max. (No condensation) (No condensation) Voltage rating 30 Vrms AC 50 Vrms AC Recommended FPC Thickness: 0.3±0.05, Gold plated contact pads Item Specification Conditions 1. Insulation resistance 500 Mø min. 100 V DC 0.3 mm pitch: 90 Vrms AC / 1 minute 2. Withstanding voltage No flashover or insulation breakdown 0.4mm pitch: 150 Vrms AC / 1 minute 150 mø max. 1 mA AC 3. Contact resistance * Including FPC conductor resistance Contact resistance: 150 mø max. 4. Durability 20 cycles No damage, cracks, or parts dislocation No electrical discontinuity of 1μs or longer Frequency: 10 to 55 Hz, single amplitude of 0.75 mm 5. Vibration Contact resistance: 150 mø max. 10 cycles in each of the 3 directions No damage, cracks, or parts dislocation No electrical discontinuity of 1μs or longer 2 Acceleration of 981m/s , 6 ms duration, 6. Shock Contact resistance: 150 mø max. sine half-wave, 3 cycles in each of the 3 axis No damage, cracks, or parts dislocation Contact resistance: 150 mø max. 7. Humidity (Steady state) 96 hours at 40°C and humidity of 90 to 95% Insulation resistance: 50Mø min. No damage, cracks, or parts dislocation Contact resistance: 150 mø max. Temperature: -40°C ➝ +15°C to 35°C ➝ +85°C➝ +15°C to 35°C 8. Temperature cycle Insulation resistance: 50Mø min. Time: -30 ➝ 2 to 3 ➝ +30 ➝ +2 to 3 No damage, cracks, or parts dislocation 5 cycles No deformation of components affecting Reflow: At the recommended temperature profile 9. Resistance to soldering heat performance. Manual soldering: 350°C for 5 seconds Note1: When passing the current through all of the contacts, use 70% of the rated current. Note2: Includes temperature rise caused by current flow. Note3: The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of connectors after installation on a board. ■Materials Part Material Finish Remarks FH30 series Color:Gray Insulator LCP UL94V-0 FH30M series Color:Beige Contacts Phosphor bronze Gold plated -------------- ■Ordering information q Series name : FH w Series No. : 30 e Blank : 0.3mm pitch ( ) FH 30 M - 80S - 0.3 SHW 05 M : 0.4 mm pitch 1 2 3 4 5 6 7 r Number of contacts : FH30 series 60, 80, 90 FH30M series 80, 96 t Contact pitch : 0.3 mm, 0.4 mm y Contact type : SHW(SMT horizontal staggered mounting) u Plating specifications : (05)…Gold plated (98)…Gold plated, 500 pieces/reel 2 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Dimensions A B Q C R9 (0.12) Vacuum pick-up surface R (0.12) D Vacuum pick-up surface ** 0.8 0.8 (E: FPC insertion slot dimension) Number of contacts indicator Notes 1: The coplanarity of each terminal lead is within 0.1. 2: Packaged on tape and reel only. Check packaging specification. 3: Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector. 4: After reflow, the terminal plating may change color, however this does not represent a quality issue. All dimensions: mm Part Number CL No. Number of Contacts FPC contact pitch A B C D E Q R 17.7 18.35 0.3 FH30-60S-0.3SHW(05) 580-0105-8-05 60 0.3 21.9 17.4 17.4 0.6 23.7 24.35 0.3 FH30-80S-0.3SHW(05) 580-0100-4-05 80 0.3 27.9 23.4 23.4 0.6 26.7 27.35 0.3 FH30-90S-0.3SHW(05) 580-0106-0-05 90 0.3 30.9 26.4 26.4 0.6 31.6 32.25 0.4 FH30M-80S-0.4SHW(05) 580-0102-0-05 80 0.4 35.8 31.2 31.2 0.8 38 38.65 0.4 FH30M-96S-0.4SHW(05) 580-0103-2-05 96 0.4 42.2 37.6 37.6 0.8 Tape and reel packaging (1,000 pieces/reel, 500 pieces/reel). Order by number of reels. 3 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 3 6.55 4.2 4.85 R0.2 R0.2 FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Recommended PCB mounting ■Recommended FPC Dimensions pattern and metal mask dimensions +0.04 0.3 -0.03 0.1±0.05 0.07±0.07 B±0.05 A No.1 No(n-1) Q±0.05 C±0.05 0.3±0.03(Land) R±0.05 0.25±0.03(Metal mask) No.2 No (n) Q±0.02 0.3±0.05 2 +0.04 0.3 R±0.02 -0.03 Detail A 0.3±0.07 B±0.03 0.3±0.07 Mark side R±0.05 0.3±0.03(Land) F±0.05 0.25±0.03(Metal mask) G±0.1 D±0.05 H MIN Recommended metal mask thickness: t=0.15 J±0.1 Note 1 : Conductor width shall be 0.1±0.05 if FPC has plating bars. All dimensions: mm Part Number CL No. Number of Contacts FPC contact pitch B C D F G H J Q R FH30-60S-0.3SHW(05) 580-0105-8-05 60 0.3 17.7 17.4 17.4 18.3 18.8 19.3 20.3 0.3 0.6 FH30-80S-0.3SHW(05) 580-0100-4-05 80 0.3 23.7 23.4 23.4 24.3 24.8 25.3 26.3 0.3 0.6 0.3 26.7 FH30-90S-0.3SHW(05) 580-0106-0-05 90 26.4 26.4 27.3 27.8 28.3 29.3 0.3 0.6 FH30M-80S-0.4SHW(05) 580-0102-0-05 80 0.4 31.6 31.2 31.2 32.2 32.7 33.2 34.2 0.4 0.8 FH30M-96S-0.4SHW(05) 580-0103-2-05 96 0.4 38 37.6 37.6 38.6 39.1 39.6 40.6 0.4 0.8 ■FH30 Series Recommended FPC Construction Material Thickness 1. Using Single-sided FPC Material Name Material (μm) Covering film layer Polyimide 1 mil thick (25) Cover adhesive (25) 0.2μm thick gold plated over 1 to Surface treatment 3 5μm thick nickel underplating Copper foil Cu 1oz 35 Base adhesive Thermosetting adhesive 25 Base film Polyimide 1 mil thick 25 Reinforcement material adhesive Thermosetting adhesive 30 Stiffener Polyimide 7 mil thick 175 Total 293 Material Thickness 2. Using Double-sided FPC Material Name Material (μm) Covering layer film (25) Polyimide 1 mil thick Cover adhesive (25) 0.2μm thick gold plated over 1 to Surface treatment 3 5μm thick nickel underplating Through-hole copper Cu 15 Copper foil Cu 1/2oz 18 Base adhesive Thermosetting adhesive 18 Base film Polyimide 1 mil thick 25 Base adhesive Thermosetting adhesive 18 (18) Copper foil Cu 1/2oz 25 Cover adhesive Thermosetting adhesive 25 Covering film layer Polyimide 1 mil thick 50 Reinforcement material adhesive Thermosetting adhesive 100 Stiffener Polyimide 4 mil thick Total 297 * To prevent release of the FPC due to it’s bending, use of the double-sided FPC with copper foil on the back side is NOT RECOMMENDED. 3. Precautions 1. This specification is a recommendation for the construction of the FH30 Series FPC (t=0.3 ± 0.05). 2. For details about the construction, please contact the FPC manufacturers. 4 (C0.5) R0.2 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 1.7±0.1 3.95±0.1 1.7±0.1 2.2±0.1 (0.8) 1.3±0.1 0.05 MIN 1.4±0.1 0±0.1 2.65±0.2 (0.5) 3.2±0.3 4.2±0.3 FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Packaging Specifications ●Embossed Carrier Tape Dimensions ●Reel Dimensions 2±0.15 (4.9) 4±0.1 12±0.1 0.4±0.1 (T: INSIDE) (U: OUTSIDE) End section Mounting section Lead section (400mm min.) +0.1 1.5 1.35±0.1 (6.8) 0 Top cover tape Embossed carrier tape No connector inserted No connector inserted Unreeling direction (10 pockets min.) (10 pockets min.) All dimensions: mm L Part Number CL No. Number of Contacts K M N T U FH30-60S-0.3SHW(05) 60 44 40.4 20.2 22.1 45.4 49.4 580-0105-8-05 FH30-80S-0.3SHW(05) 80 44 40.4 20.2 28.1 45.4 49.4 580-0100-4-05 FH30-90S-0.3SHW(05) 90 44 40.4 20.2 31.1 45.4 49.4 580-0106-0-05 FH30M-80S-0.4SHW(05) 80 56 52.4 26.2 36 57.4 61.4 580-0102-0-05 FH30M-96S-0.4SHW(05) 96 56 52.4 26.2 42.4 57.4 61.4 580-0103-2-05 Tape and reel packaging (1,000 pieces/reel). ■Temperature Profile ● Using Lead-free Solder Paste HRS test condition MAX 250ç Solder method :Reflow, IR/hot air 250 Environment :Room air 230ç Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part 200 200ç Number:M705-221CM5-32-10.5) Test board :Glass epoxy FH30:45∞80∞1.6mm thick 150 150ç FH30M:70∞130∞1.6mm thick Land dimensions :0.3mm∞1.7mm 100 Metal mask :0.15mm thick 0.25mm∞1.7mm 50 25ç (60 sec.) 90 to 120 sec. (30 sec.) The temperature profiles shown are based on the above Preheating Soldering conditions. 0 Start In individual applications the actual temperature may vary,depending on solder paste type, volume / thickness and Time (Seconds) board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. 5 (Ø13) +0.1 Ø1.5 0 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Temperature(ç) +0.15 1.7 0 (N) M±0.1 1.75±0.1 L±0.1 K±0.3 (Ø380) (Ø80) FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Operation and Precautions Operation and Precautions q Install on the PC board with the actuator open. e Actuator closing after the FPC is fully inserted. Rotate the actuator down to a full stop, pushing it at the center. w FPC Insertion Orient the FPC with the contact pads facing down. Insert in the connector at an angle, assuring that the positioning tabs are placed in the corresponding positioning tab areas on both sides of the insulator body. Lower the FPC to a position parallel to the mounting surface. Verify the correct position by slightly pulling horizontally on the FPC. Positioning tab area (each side) r Removing the FPC Carefully rotate the actuator up, lifting it at the center. Lift the FPC slightly to clear the positioning tabs and withdraw it from the connector. Positioning part 6 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors ■Precautions Operation and Precautions q Actuator operation w FPC Insertion and closing of the actuator. The actuator rotates at the center of it’s shaft, as Do not insert the FPC on an angle as illustrated in the illustrated in the figure below. photograph below. Rotation shaft Be careful not to apply excessive force when operating the actuator from the open position (before the FPC has been inserted). Exercise care not to touch the contacts with Properly insert the FPC positioning tabs into the fingernails or any other object. corresponding areas on both sides of the insulator body. Incorrect FPC insertion Correct FPC insertion During the closing of the actuator do not pull up or e Make sure that the FPC does not rub against the push on it directly down. insertion slot or the contacts, as illustrated on the Do not grasp the actuator and pull on it (photograph figure below. below). 7 Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors Operation and Precautions Closing of the actuator. r Opening of the actuator Rotate down pushing it at the center or evenly at Rotate up, lifting it at the center or evenly at each end each end, as shown on the photographs below. Do of the actuator. not push at one end only. Do not lift at one end only. t Forces to the FPC after insertion and closing of the actuator. Do not apply upward pull-force to the FPC close to the connector. If a need arise to route the FPC upward, assure that it is NOT transferring any forces to the closed actuator. 8 Powered by TCPDF (www.tcpdf.org) Jun.1.2018 Copyright 2018 HIROSE ELECTRIC CO., LTD. All Rights Reserved.