The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height U.FL Series Up to 6GHz Transmission Speed Mated Height Comparison (With E.FL series) E.FL-LP-040 U.FL-LP-040 E.FL-LP-066 U.FL-LP-066 U.FL-LP(V)-040 U.FL E.FL Space Factor of Mated ConnectorFeatures 1.Extremely Small Occupied Mounting Area 2 Reduced board space requirement by 18% to 7.7mm , when Cable compared with Hirose’s E.FL connectors. U.FL-LP-040 Plug 2.Light Weight Dia.0.81 One of the world’s lightest coaxial connectors. Receptacle: 15.7mg U.FL-R-SMT 3.Frequencies of Up to 6GHz Receptacle To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency Cable U.FL-LP-066 Plug performance from DC to 6 GHz. Dia.1.32 4.Board Placement with Automatic Equipment Dia.1.13 Supplied on tape-and-reel packaging. U.FL-R-SMT 5.Use of Ultra-fine Teflon Cable Receptacle ® Several of ultra-fine single and double shielded Teflon NEW coaxial cables terminate to U.FL plug. Cable U.FL-LP(V)-040 Plug 6. Simple Disconnection Dia.0.81 Dedicated tool allows reliable un-mating of the plug. 7.User Friendly Mating Operation U.FL-R-SMT Tactile lock feeling ensures and confirms reliable connection. Receptacle NEW CableApplications U.FL-LP-062 Plug Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS, Dia.1.00 electronic measuring instruments, etc. U.FL-R-SMT Receptacle NEW Cable U.FL-LP-088 Plug Dia.1.37 U.FL-R-SMT Receptacle *Teflon is a registered trademark of DuPont. 2004.2 1 1.9(2.0Max) 2.5Max 2.4Max 2.4Max 2.0Max 2.5Max 2.4(2.5Max) 3(3.2Max) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Product Specifications Nominal characteristic impedance 50 ohms Operating temperature range -40˚C to +90˚C Ratings Voltage rating 60 V AC (rms) Operating humidity 90% max. Frequency range DC to 6 GHz Item Specification Conditions 1. Contact resistance Center: 20 m ohms max. 10 mA max. Outside: 10 m ohms max. 2. Insulation resistance 500 M ohms min. 100 V DC 3. Withstanding voltage No flashover or insulation breakdown. 200 V AC / 1 minute 4. V.S.W.R.* Part No. Up to 3GHz 3 to 6GHz U.FL-LP-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.35 Max U.FL-LP(V)-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.3 Max U.FL-LP-068 dia.1.13mm Coaxial Cable Assembly 1.3 Max 1.4 Max U.FL-LP-066 dia.1.32mm Coaxial Cable Assembly 1.3 Max 1.5 Max U.FL-LP-062 dia.1mm Coaxial Cable Assembly 1.3 Max 1.3 Max U.FL-LP-088 dia.1.37mm Coaxial Cable Assembly 1.3 Max 1.4 Max 5. Center contact holding force 0.15 N min. Measured with a Ø 0.475 pin gauge 6. Durability Contact resistance (mating/un-mating, Center: 25 m ohms max. 30 cycles with corresponding plug) Outside: 15 m ohms max. 7. Vibration Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration 2 No electrical discontinuity of 1µs min. of 59m/s , for 5 cycles in the direction of each of the 3 axis. 2 8. Shock No damage, cracks or parts dislocation. Acceleration of 735 m/s , 11ms duration, sine half-wave waveform, 6 cycles in each of 3 axes. 9. Humidity No damage, cracks or parts dislocation. (Steady state) Insulation resistance 100 M ohms min.(when humidity high) 96 hours at temperature of 40ç and humidity of 95%. Insulation resistance 500 M ohms min.(when dry) 10. Temperature cycle No damage, cracks or parts dislocation. Temperature:-40˚C +5 to +35˚C +90˚C +5 to +35˚C / / / Contact resistance:25 m ohms max. (Center) Time: 30 5 max. 30 5 max.(Minutes) / / / 15 m ohms max. (Outside) 5 cycles 11. Salt spray test No excessive corrosion 5% salt water solution, 48 hours *V.S.W.R. Measurement System The above V.S.W.R. standard values were measured using the measurement connection shown below. Note 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. Note 2: Board type connectors were mounted to a 50Ω glass epoxy board and measurements were conducted with SMA conversion adapters attached. Material/Finishes Part Material Finish Remarks Shell Phosphor bronze Silver plated ————— Male center contact Brass Gold plated ————— Female center contact Phosphor bronze Gold plated ————— Plug PBT Color: Black UL94V-0 Insulator Receptacle LCP Color: Beige UL94V-0 2 +0.1 Ø1.5 0 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Receptacles Cut Out Prohibition Area 4±0.05 GND GND 1.9±0.05 SIG GND Ø2 GND 3 SIG 2.6 Note 1: Receptacles of (01) specification are sold by the 0.6 1±0.05 bag with 100 pieces per bag. Please order in pack units. Note 2: Receptacles of (10) specification are sold by the reel (which contains 2,500 pieces). Recommended PCB mounting pattern Please order in reel units. Note 3: This area may be covered by insulating material. Part No. CL No. Packaging Weight (mg) U.FL-R-SMT(01) 331-0471-0-01 Bag packaging (100 pieces/bag) 15.7/unit U.FL-R-SMT(10) 331-0471-0-10 Reel packaging (2500 pieces/reel) Packaging Specifications Embossed Carrier Tape Dimensions 2±0.1 4±0.1 0.3 Center contact Unreeling direction 1.6 8±0.1 Reel Dimensions 1.8 14 3 Ø21 Ø13 12±0.3 5.5±0.1 1.75±0.1 (3.1) 2.6 1.25 0.35 1.8 1.2Max(Note 3) Ø330±2 1±0.05 1.05±0.05 2.2±0.05 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Cable Assembly (Plug) U.FL-LP-040 U.FL-LP-066 U.FL-LP(V)-040 U.FL-LP-062 U.FL-LP-088 Part No. 4 3.4 5 4 4 2.5mm Max. 2.5mm Max. 2.0mm Max. 2.4mm Max. 2.4mm Max. Mated Height (2.4mm Nom.) (2.4mm Nom.) (1.9mm Nom.) (2.3mm Nom.) (2.3mm Nom.) Dia. 1.13mm and Applicable Dia. 0.81mm Dia. 0.81mm Dia. 1mm Dia. 1.37mm Dia. 1.32mm cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Weight (mg) 53.7 59.1 34.8 45.5 71.7 Cable Guide Cable Specification Cable Description Inner Dielectric Outer Jacket Nominal Nominal attenuation Type * * Conductor Diameter Conductor Diameter Impedance At 3GHz At 6GHz Dia.0.81mm 7/0.05 SA Dia.0.40 Single Dia.0.81 04 50 ohms 6.45dB/m 9.42dB/m Coaxial Cable (AWG36) PFA Shield SA PFA Dia.1.13mm 7/0.08 SA Dia.0.68 Single Dia.1.13 3.43dB/m 5.13dB/m 068 50 ohms Coaxial Cable (AWG32) FEP Shield SA[TA] FEP [3.73dB/m] [5.44dB/m] Dia.1.32mm 7/0.08 SA Dia.0.66 Double Dia.1.32 066 50 ohms 3.8dB/m 5.6dB/m Coaxial Cable (AWG32) FEP Shield TA FEP Dia.1mm 7/0.071 SA Dia.0.62 Tape, single Dia.1 062 50 ohms 3.1dB/m 4.4dB/m Coaxial Cable (AWG33) FEP Shield TAT FEP Dia.1.37mm 7/0.102 SA Dia.0.88 Single Dia.1.37 088 50 ohms 2.8dB/m 4.3dB/m Coaxial Cable (AWG30) FEP Shield TA FEP (data as provided by cable suppliers, for reference only) * SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin 4 1.93 3 1.93 3 1.5 2.8 1.8 2.8 1.85 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. How to Specify Plug Cable Assembly Dimensions of U.FL Series assembly products should be made as indicated below. Double-Ended Cable Assembly Single-Ended Cable Assembly L L Total Standard Tolerance for Total Length of Cable AssemblyOrdering Information Total Length(mm) Standard Tolerance (mm) U.FL - [] LP - [] - A - (L) < < 00350 L 00200 ±04 = = 1 2 3 4 < 02000