The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. NEW Ultra Small Surface Mount Coaxial Connectors – 1.4mm Mated Height W.FL Series – Further downsizing of FL series in response to the market needs. Occupied Mounting Area 2.0 2.0 FeaturesMated Height Comparison(With U.FL series) 2 1. Mounting area of only 3.4mm 2. The board mounted receptacle weights only 5.6 mg 3. Accepts high frequency transmission of DC to 6GHz U.FL-LP-040 U.FL-LP-066 4. Receptacle supplied on tape-and-reel for U.FL-LP(V)-040 W.FL-LP-040 4. placement on the board with automatic equipment 5. Plugs are terminated with ultra-fine Teflon® 4. insulated coaxial cables W.FL Series U.FL Series 6. Un-mating with a simple tool Applications Mobile phones, Wireless LAN, Bluetooth protocol devices, PDA, GPS, electronic measuring instruments and any application requiring high frequency transmission over coaxial line, where space is limited. Plug 2.85 Cable Dia. 0.81 W.FL-R-SMT-1 Receptacle * Teflon is a registered trademark of DuPont. 2004.4 1 1.4 (MAX1.55) 1.4 (MAX1.55) 1.9 (MAX2.0) 2.4 (MAX2.5) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Product Specifications Nominal characteristic -40ç to +90ç 50 ohms Operating temperature range impedance (Relative humidity 90% max.) Ratings -40ç to +70ç Frequency range DC to 6GHz Operating humidity (Relative humidity 90% max.) Materials and Finishes Item Specification 1. Contact resistance Center: 20m ohms max. Outside: 10m ohms max. 2. Insulation resistance 500M ohms min., 100V DC 3. Withstanding voltage 200V AC / 1 minute 1.3 max. (Up to 3GHz) 4. V.S.W.R.(Note) 1.35 max. (3 to 6GHz) Note:V.S.W.R. Measurement System Note:Measured as shown on the block diagram below. Note:Test connection and measurement setup. Note1:Cable type connector measurements. Network Analyzer With SMA conversion adapters mated with W.FL plug Test Set Test Port at each end of the 100cm long ultra-fine coaxial cable. Note2:Board type connector measurements. D.U.T Termination Mounted on a 50 ohms glass epoxy board. Test Port Cable Measurements were conducted with SMA conversion adapters attached. Material/Finishes Part Component Material Finish/Remarks Shell Phosphor bronze Silver plated Plug Insulator PBT Black, UL94V-0 Socket center contact Phosphor bronze Gold plated Shell Phosphor bronze Silver plated Receptacle Insulator LCP Black, UL94V-0 Pin center contact Brass Gold plated Plug 2.85 Plugs can be ordered only terminated to the cable. 2 1.15 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. How to Specify Cable Assembly Double-ended cable assembly Single-ended cable assembly *** L(mm) L(mm) Ordering Information Standard tolerances for (L)** (L)(mm) Standard Tolerance (mm) [[ ]] -- -- -- -- W.FL 2LP 04N A (L) *L=35 to 200 ±4 1 2 3 4 5 L=200 to 500 ±8 L=500 to 1000 ±12 L=1000 ±1.5% of (L) / 1 Series name W.FL *Minimum available length (L) is 35mm LP2: Single ended **Contact nearest HRS representative if different 2 Assembly type tolerances are required. 2LP: Double ended ***Contact Nearest HRS representative if one end 3 Cable type 04N: 0.81mm dia. ultra-fine coaxial cable requires preparation. Cable color 4 1: White, 2: Black 5 Total length (mm) Length (L) Receptacle BRecommended PCB Mounting Pattern 2.6 0.85 0.3 0.25 1.4 0.5 0.3 SIGNAL TERMINAL SIGNAL TERMINAL 1.7 PAD GND 2 GND No conductive traces in this area Recommended screen thickness: 0.1mm to 0.12mm Part Number CL No. Packaging Weight / EA W.FL-R-SMT-1(10) 331-0482-6-10 Reel packaging (2000 pieces/reel) 5.6 mg 3 1.3 1.7 2 1.3 1.3 0.65 1.5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Conversion Adapters SMA Conversion Adapter (W.FL side jack – SMA side plug) (10.3) 8HEX W.FL SMA Note:Used for performance measurements only. The W.FL mating side has lower retention Part No. CL No. force than the regular product when mated to HRMP-W.FLJ 311-0367-3 the corresponding part. SMA Conversion Adapter (W.FL side plug – SMA side jack) 13.8 6 ( 4.05 ) 5.6 SMA W.FL 1/4-36UNS-2A Note:Used for performance measurements only. The W.FL mating side has lower retention Part No. CL No. force than the regular product when mated to HRMJ-W.FLP 311-0368-6 the corresponding part. SMA Conversion Adapter ( 18.35 ) 6 (4) 5.5 1/4-36UNS-2A Note:When mating with corresponding part (W.FL- Part No. CL No. R-SMT-1) it must be pressed down and held HRMJ-W.FLP-ST1 311-0386-8 to make complete connection. Receptacle Inspection Adapter Used for inspecting the performance parameters of the cable assembly. 12.1 ( 7.9 ) 4.2 ( 4.4 ) 1 7HEX M5∞0.5 Part No. CL No. W.FL-R-1 331-0483-9 4 Ø6.35 Ø6.35 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plug Extraction Tool-Used for Un-mating of the plug (100 ) 40 Part No. CL No. W.FL-LP-N 331-0492-0 BPackaging Specifications- Receptacle W.FL-R-SMT-1(10) Embossed Carrier Tape Dimensions 2 4 Center contact terminal 8 Unreeling direction Reel Dimensions 14 1.8 5 Ø21 (Ø15) Ø13 Ø1.5 12 5.5 1.75 Ø330 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Usage Precautions 1. Plugs 1) Mating. 1) Both parts must be aligned on the axis to mate correct. Press down firmly. A tactile “click” will confirm fully mated condition. 2) Un-mating. 1) Fully insert the tool under the plug’s flanges as shown. (1) Mating/ un-mating W.FL-LP-N plug extraction tool 1) Apply even force upward until the plug is free. W.FL Cable Assembly W.FL-R-SMT-1 Do not twist, apply excessive forces or sharp bends to the cable. W.FL-LP-040 ∞ Cable Assembly W.FL-R-SMT-1 (2) Cable handling 2N max Receptacle ∞ (3) Precautions Do NOT forcefully twist or deform wires. 2. Receptacles (1) Recommended soldering temperature profile Peak temperature and time [ç] 240ç 3 seconds 260 240 220 200 183ç 180 160 Preheating (130ç to 165ç) 140 120 100 Within 2 minutes 80 40 to 50 seconds Time 1) The temperature profile indicates the board surface temperature at the point of contacts with the connector terminals. 2) The temperature may vary, depending on the board size, the solder paste type and thickness. 0.1 to 0.12 mm (2) Recommended screen thickness ® 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933 http://www.hirose.com http://www.hirose-connectors.com The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpo The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements. se of improvements. 6 Temperature on Top Portion of Part