ø8·10·1·16 AP Series Miniature Pilot Lights Super Bright LEDs with built-in current-limiting resistor and reverse polarity protection diode • Space saving miniature style • Long life • Illumination colors: amber, blue, green, pure white, red, white, and yellow (blue and pure white available for AP8M and AP1M only) • Marking is available on flat lens units. (except AP8M series) • Built-in protection diode ensures a reverse withstand voltage of 100V. • UL recognized and CSA certified AP6M Series AP2M Series AP6M Series Dome Flat Dome Flat AP2M Series AP1M Series AP8M Series AP1M Series Dome Flat Dome Flat AP6M Series AP2M Series AP8M Series AC adapter unit AC adapter unit DC-DC converter unit DC-DC converter unit Flasher unit • Pilot Light Input Type Full voltage Operating Voltage 5V DC 6V DC 1V AC/DC 1V DC 4V AC/DC 4V DC AP1M, AP8M: 9 mA AP6M, APM: AP1M, AP8M: 9 mA AP6M, APM: AP1M, AP8M: 9 mA AP6M, APM: Rated Current (yellow: 15 mA) 33 mA (yellow: 15 mA)  mA (yellow: 15 mA) 11 mA AP6M, APM: A (amber), G (green), R (red), Y (yellow), W (white) Illumination Color Code AP8M, AP1M: A (amber), G (green), PW (pure white), R (red), S (blue), Y (yellow), W (white) Operating Temperature –0 to +55°C (no freezing) Operating Humidity 45 to 85% RH (no condensation) Insulation Resistance Between live and dead parts: 100 MΩ minimum (500V DC megger) Dielectric Strength Between live and dead parts: 1000V, 1 minute Reverse Withstand Voltage 100V — 100V — 100V Solder Terminal Soldering 350°C maximum (3 sec)  Applicable Wire ø1.0 or 0.75 mm maximum (20 to 16 AWG) AP6M: 7.5g APM: 4.5g Weight (approx.) AP1M: .5g AP8M: .0g Degree of Protection AP6M, APM, AP1M: IP65 AP8M: IP40 (according to IEC 6059) • AC Adapter/DC-DC Converter (Option) • Flasher Unit (Option) Unit AC Adapter DC-DC Converter Applicable Unit AP6M (1V and 4V DC rating only) Applicable Unit AP6M and APM (6V rating only) Operating Voltage 1/4V DC compatible ±10% Adjustable between approximately 30 to 600 100/110V AC, 00/0V AC 110V DC Flashing Period Operating Voltage cycles per minute (period 0.1 to  sec) 50/60 Hz (90 to 140V DC) Current Draw 4 mA (OFF) to 6 mA (ON) Power Consumption 1.6 VA maximum 1W maximum 50V AC 140V DC Terminal Style M3 screw Insulation Voltage Insulation Between live and dead parts: Weight (approx.) 13.5g Resistance 100 MΩ minimum (500V DC megger) Between live and dead parts: 000V, 1 minute Dielectric Strength Between I/O terminals: Between I/O terminals: 000V AC/, 1 minute 1500V AC, 1 minute Terminal Style M3 screw Weight (approx.) 38g 0g 4 (07/03/26) ø16 AP Series Miniature Pilot Lights AP6M Series (ø16) Shape Operating Voltage Type No. Ordering Type No. Package Quantity Lens Color Code Dome AP6M66➁ 1 6V DC ±5% AP6M66➁ AP6M66➁PN10 10 AP6M11➁ 1 1V DC ±10% AP6M11➁ AP6M11➁PN10 10 Specify a lens color code in place of ➁ AP6M➁ 1 in the Type No. 4V DC ±10% AP6M➁ AP6M➁PN10 10 A: amber Flat (marking type) AP6M166➁ 1 G: green 6V DC ±5% AP6M166➁ R: red AP6M166➁PN10 10 W: white Y: yellow AP6M111➁ 1 1V DC ±10% AP6M111➁ AP6M111➁PN10 10 AP6M1➁ 1 4V DC ±10% AP6M1➁ AP6M1➁PN10 10 The LED cannot be removed. The lens can be removed and replaced. • Degree of protection: IP65 • AC Adapter, DC-DC Converter, Flasher Unit Type No. Unit Operating Voltage Applicable Pilot Light Package Quantity (Ordering Type No.) 100/110V AC AP6-016D AC Adapter AP6M66➁ (dome: 6V DC) 00/0V AC AP6-06D AP6M166➁ (flat: 6V DC) DC-DC Converter 110V DC (90 to 140V DC) AP6-016DD 1 AP6M11➁ (dome: 1V DC) AP6M➁ (dome: 4V DC) Flasher Unit 1/4V DC UZ6-F10 AP6M111➁ (flat: 1V DC) AP6M1➁ (flat: 4V DC) Dimensions / Panel Cut-out With AC Adapter, DC-DC Converter, or Flasher Unit Terminal Cover: AP-VL3 Panel Thickness 0.8 to 6 AC Adapter DC-DC Converter M3 Screw Positive Terminal Gasket Dome Flasher Unit 2.2 1.5 + – 58.7 18 5.5 21.5 8 Width 2.8×0.4t 71 1.3 Negative Terminal 13.5 29.5 Flat Panel Cut-out Terminal cover is not supplied. When using terminal covers, order AP-VL3 terminal covers. 5.5 9.5 Terminal Arrangement (Bottom View) Marking Plate + – Positive Terminal Negative Terminal Engraving depth: 0.5 mm maximum Marking plate material: White acrylic All dimensions in mm. (07/03/26) 5 ø12.9 ø16.2 0 +0.2 ø18 ø18 ø15.6 ø15.6 7 6 TOP X X1 18 ø1 AP Series Miniature Pilot Lights AP2M Series (ø12) Shape Operating Voltage Type No. Ordering Type No. Package Quantity Lens Color Code Dome APM66➁ 1 6V DC ±5% APM66➁ APM66➁PN10 10 APM11➁ 1 1V DC ±10% APM11➁ APM11➁PN10 10 Specify a lens color code in place of ➁ APM➁ 1 in the Type No. 4V DC ±10% APM➁ APM➁PN10 10 A: amber Flat (marking type) APM166➁ 1 G: green 6V DC ±5% APM166➁ R: red APM166➁PN10 10 W: white Y: yellow APM111➁ 1 1V DC ±10% APM111➁ APM111➁PN10 10 APM1➁ 1 4V DC ±10% APM1➁ APM1➁PN10 10 • The LED cannot be removed. The lens can be removed and replaced. • Degree of protection: IP65 • AC Adapter, DC-DC Converter Unit Operating Voltage Type No. Applicable Pilot Light Package Quantity 100/110V AC AP-016D AC Adapter AP6M66➁ (dome: 6V DC) 00/0V AC AP-06D 1 AP6M166➁ (flat: 6V DC) DC-DC Converter 110V DC (90 to 140V DC) AP-016DD Dimensions / Panel Cut-out With AC Adapter or DC-DC Converter Terminal Cover: AP-VL3 Panel Thickness 0.8 to 6 AC Adapter / DC-DC Converter M3 Screw Positive Terminal Gasket Dome 2.2 1.5 + 5.5 21.5 Width 2.8×0.4t 58.7 18 29.5 71 11.5 1.3 Negative Terminal Panel Cut-out Flat Terminal cover is not supplied. When using terminal covers, order AP-VL3 terminal covers. 5.5 9.5 Terminal Arrangement (Bottom View) Marking Plate + – Positive Terminal Negative Terminal Engraving depth: 0.5 mm maximum Marking plate material: White acrylic All dimensions in mm. 6 (07/03/26) ø9.4 +0.2 ø12.2 0 ø14 ø14 ø12 ø12 5 – 5.5 TOP X X1 18 5.5 ø10 AP Series Miniature Pilot Lights AP1M Series (ø10) Shape Operating Voltage Type No. Ordering Type No. Package Quantity Lens Color Code Dome AP1M55➁ 1 5V DC ±5% AP1M55➁ AP1M55➁PN10 10 AP1M11➁ 1 1V AC/DC ±10% AP1M11➁ Specify a lens color AP1M11➁PN10 10 code in place of ➁ in the Type No. AP1M➁ 1 4V AC/DC ±10% AP1M➁ A: amber AP1M➁PN10 10 G: green Flat (marking type) AP1M155➁ 1 PW: pure white 5V DC ±5% AP1M155➁ R: red AP1M155➁PN10 10 S: blue W: white AP1M111➁ 1 Y: yellow 1V AC/DC ±10% AP1M111➁ AP1M111➁PN10 10 AP1M1➁ 1 4V AC/DC ±10% AP1M1➁ AP1M1➁PN10 10 • The LED cannot be removed. The lens can be removed and replaced. • Degree of protection: IP65 Dimensions / Panel Cut-out 2.2 1.5 Panel Thickness 0.8 to 6 Gasket Dome 5.5 21.5 8 10 29.5 Panel Cut-out Flat 5.5 9.5 Terminal Arrangement (Bottom View) Marking Plate Projection – + Positive Terminal Negative Terminal Engraving depth: 0.5 mm maximum Marking plate material: White acrylic All dimensions in mm. (07/03/26) 7 ø7.7 ø7.7 0 ø10.1 +0.2 ø12 ø12 ø10 ø10 4 2.8 - + 6.1 6.1 ø8 AP Series Miniature Pilot Lights AP8M Series (ø8) Shape Operating Voltage Type No. Ordering Type No. Package Quantity Lens Color Code Dome AP8M55➁ 1 5V DC ±5% AP8M55➁ AP8M55➁PN10 10 AP8M11➁ 1 1V AC/DC ±10% AP8M11➁ Specify a lens color AP8M11➁PN10 10 code in place of ➁ in the Type No. AP8M➁ 1 4V AC/DC ±10% AP8M➁ A: amber AP8M➁PN10 10 G: green Flat AP8M155➁ 1 PW: pure white 5V DC ±5% AP8M155➁ R: red AP8M155➁PN10 10 S: blue W: white AP8M111➁ 1 Y: yellow 1V AC/DC ±10% AP8M111➁ AP8M111➁PN10 10 AP8M1➁ 1 4V AC/DC ±10% AP8M1➁ AP8M1➁PN10 10 • The lens or LED cannot be removed or replaced. • Degree of protection: IP40 Dimensions / Panel Cut-out 2.2 1.5 Panel Thickness 0.8 to 6 Gasket Dome 5.5 21.5 8 9.5 29.5 Panel Cut-out Flat 5.5 8.5 Terminal Arrangement (Bottom View) Projection Positive Terminal Negative Terminal All dimensions in mm. 8 (07/03/26) +0.2 0 ø8.1 ø9.8 ø9.8 ø8 ø8 3 2.8 ø8·10·1·16 AP Series Miniature Pilot Lights Accessories Ordering Package Shape Type Material Type No. Remarks Type No. Quantity Locking Ring Wrench • Used to tighten the locking ring when in- ø16 MT-001 MT-001 1 stalling an AP unit onto an panel. • Tighten the locking ring using a recom- ø1 MT-00 MT-00 1 mended tightening torque. Metal Type No. Size (nickel-plated brass) MT-001 ø18 ø10 MT-003 MT-003 1 MT-00 ø14 MT-003 ø1 ø8 MT-004 MT-004 1 60 MT-004 ø9.5 Removal Tool • Used to remove the AC adapter, DC-DC converter, or flasher unit. 90 Stainless steel MT-100 MT-100 1 .5 1.0 Mounting Hole Plug • Degree of protection: IP65 Metal (diecast) AL-BM6 AL-BM6 1 Locking ring (plastic) ø16  6 • Degree of protection: IP65 Nitryl rubber (black) AL-B6 AL-B6PN05 5 • Degree of protection: IP65 ø14 ø1 Nitryl rubber (black) AL-B AL-BPN05 5 • Degree of protection: IP65 ø1 ø10 Nitryl rubber (black) AL-B1 AL-B1PN05 5 • Degree of protection: IP65 ø9 ø8 Nitryl rubber (black) AL-B8 AL-B8PN05 5 • Replacement Parts for AP6M/AP2M/AP1M Ordering Package Shape Type Type No. Lens Color Code Type No. Quantity Lens A (amber), G (green), R (red), W (white), Dome lens AP6M-L➁ AP6M-L➁PN05 5 Y (yellow) (Note 1) AP6M A (amber), C (clear), G (green), R (red), Flat lens AP6M-L1➁ AP6M-L1➁PN05 5 Y (yellow) (Note ) A (amber), G (green), R (red), W (white), Dome lens APM-L➁ APM-L➁PN05 5 Y (yellow) (Note 1) APM A (amber), C (clear), G (green), R (red), Flat lens APM-L1➁ APM-L1➁PN05 5 Y (yellow) (Note ) A (amber), G (green), R (red), S (blue), Dome lens AP1M-L➁ AP1M-L➁PN05 5 W (white), Y (yellow) (Note 1) AP1M A (amber), C (clear), G (green), R (red), Flat lens AP1M-L1➁ AP1M-L1➁PN05 5 S (blue), Y (yellow) (Note ) Marking Plate AP6M AP6M-P1W AP6M-P1WPN05 5 APM Flat lens APM-P1W APM-P1WPN05 5 White AP1M AP1M-PN1W AP1M-PN1WPN05 5 Diffusion Plate AP1M Dome lens AP1M-PNW AP1M-PNWPN05 5 White Terminal Cover AC adapter AP6M DC-DC AP-VL3 AP-VL3 1 APM converter Flasher unit 17.2 3 11.3 Specify a lens color code in place of ➁ on the Ordering Type No. Note 1: On the dome lens type, use a white (W) lens for white (W) illumination. Note : On the flat lens type, use a clear (C) lens for white (W) illumination. (07/03/26) 9 Size 20.2 4.4 4.8 4.  ø17.8  ø18 1.8 ø16.5 16 TOP TOP TOP TOP TOP TOP ø8·10·1·16 AP Series Miniature Pilot Lights Safety Precautions • Turn off power to the AP series pilot lights before installation, re- create a fire hazard. Tighten the M3 terminal screws to a torque moval, wiring, maintenance, and inspection. Failure to turn power of 0.6 to 1.0 N·m. Failure to tighten terminal screws may cause off may cause electrical shocks or fire hazard. overheating and fire. • For wiring, use wires of proper size to meet the voltage and cur- rent requirements. Improper wiring may cause overheating and Instructions • Panel Mounting • Wiring When mounting the AP series pilot lights on a panel, use the optional locking ring wrench. Do not use pliers. Excessive 1. Note the positive and negative polarities when wiring. tightening will damage the locking ring. . All DC type AP series pilot lights contain a diode for protection against reverse polarity and a current limiting resistor, Unit Tightening Torque eliminating the need for external resistors. AP6M 0.88 N·m 3. Solder the terminal at 350°C within 3 seconds using a 60W APM 0.78 N·m soldering iron. SnAgCu type lead-free solder is recommended. AP1M 0.9 N·m When soldering, do not touch the pilot light housing with the AP8M 0.9 N·m soldering iron. Also ensure that no tensile force is applied to the terminal. Do not bend the terminal or apply excessive force to • Installing the AC Adapter, DC-DC Converter, and the terminal. Use a non-corrosive rosin flux. Flasher Unit 1. Make sure that the voltage rating and terminal style of the AP • Marking series pilot lights are applicable to the AC adapter, DC-DC AP6M, APM, and AP1M round flat lenses contain a white converter, and flasher units. marking plate inside the lens. (AP8M lens cannot be removed.) . Install the pilot light into a panel cut-out before mounting an AC • DC-DC Converter adapter, DC-DC converter, or flasher unit. Note that the pilot light DC-DC converters employ an electronic oscillating circuit. Osci- cannot be installed in a panel cut-out with an AC adapter, DC- llating sounds may be heard depending on operating conditions, DC converter, or flasher unit mounted. but will not affect performance characteristics. 3. When installing an AC adapter, DC-DC converter, or flasher unit, make sure that the TOP marking is on the same side as the • Flasher Unit TOP making of the pilot light. AC adapter, DC-DC converter, and Pierce the round mark on the nameplate on top of the flasher unit flasher unit are snapped on to the back of the pilot light. with a flat screwdriver and adjust the variable resistor inside.Turn 4. To remove the AC adapter or DC-DC converter, or flasher unit, clockwise to lengthen the flashing period. insert the tip of the removal tool into the joint hook and pull towards you as shown in the photo below. Positive Terminal TOP X2 Negative Terminal Negative Terminal TOP Nameplate TOP X1 Positive Terminal Positive Terminal AP2 Series TOP Note: Do not apply excessive force to terminals X1 and X2 during wiring. Nameplate X2 Negative Terminal AP6 Series Negative Terminal Positive Terminal X1 Positive Terminal TOP Negative Terminal X2 Negative Terminal TOP Nameplate X1 Positive Terminal Note: Do not apply excessive force to terminals X1 and X2 during wiring. 5. When using an AC adapter or DC-DC converter, or flasher unit where the units are subjected to noise, connect a noise supressor across terminals X1 and X as shown in the diagram below. Noise Suppressor X1 X2 10 (07/03/26) ø16 AP6S Series Miniature Pilot Lights Miniature Pilot Lights with Super Bright LEDs • IDEC’s LSTD LED lamps with BA9S base • Six illumination colors: amber, green, red, blue, white, and yellow • Screw terminal and solder/tab terminal available • Degree of protection: IP65 • The current-limiting resistor in the LED lamp eliminates the need for external resistors Specifications Lens AL6➁-L1 Illumination LED Operating Voltage 6V AC/DC, 1V AC/DC, 4V AC/DC Marking Plate AL6➁-W Lens Color Code A (amber), G (green), R (red), S (blue), W (white), Y (yellow) Lens Holder Built-in LED Lamp LSTD LED Lamp Type No. LSTD-6➁ LSTD-1➁ LSTD-➁ Rated Voltage 6V AC/DC 1V AC/DC 4V AC/DC Gasket A, R, W G, S, PW A, G, R, PW, S, W Current Draw AC 8 mA 8 mA 11 mA 10 mA LED lamp DC 7 mA 5.5 mA 10 mA 11 mA LED Lamp Color Code A (amber), G (green), PW (pure white), R (red), S (blue), W (white) Operating Temperature –0°C to +50°C (no freezing) Operating Humidity 45 to 85% RH (no condensation) Insulation Resistance Between live and dead metal parts: 100mΩ minimum (500V DC megger) Dielectric Strength Between live and dead metal parts: 000V AC, 1 minute Screw terminal: M.6 Terminal Style  Tab terminal: #110 solder/tab terminal (applicable cable: 1.5 mm max.) Housing Material Black plastic Degree of Protection IP65 (waterproof/oiltight) (according to IEC 6059) Terminal screw type: 18g Weight (approx.) Solder/tab screw type: 9g Types Type No. Built-in LED Shape Terminal Style Operating Voltage Lens Color Code (Ordering Type No.) (Type No.) Round 6V AC/DC±5% AP6MS5➁ LSTD-6➁ Solder/Tab Terminal 1V AC/DC±10% AP6MS53➁ LSTD-1➁ 4V AC/DC±10% AP6MS54➁ LSTD-➁ 6V AC/DC±5% AP6MS5M➁ LSTD-6➁ Screw Terminal 1V AC/DC±10% AP6MS53M➁ LSTD-1➁ 4V AC/DC±10% AP6MS54M➁ LSTD-➁ Square 6V AC/DC±5% AP6QS5➁ LSTD-6➁ Solder/Tab Terminal 1V AC/DC±10% AP6QS53➁ LSTD-1➁ 4V AC/DC±10% AP6QS54➁ Specify a lens color LSTD-➁ code in place of ➁ in 6V AC/DC±5% AP6QS5M➁ LSTD-6➁ the Type No. Screw Terminal 1V AC/DC±10% AP6QS53M➁ LSTD-1➁ A: amber 4V AC/DC±10% AP6QS54M➁ LSTD-➁ G: green Rectangular 6V AC/DC±5% AP6HS5➁ LSTD-6➁ R: red S: blue Solder/Tab Terminal 1V AC/DC±10% AP6HS53➁ LSTD-1➁ W: white 4V AC/DC±10% AP6HS54➁ LSTD-➁ Y: yellow 6V AC/DC±5% AP6HS5M➁ LSTD-6➁ Screw Terminal 1V AC/DC±10% AP6HS53M➁ LSTD-1➁ 4V AC/DC±10% AP6HS54M➁ LSTD-➁ Rectangular with 3-sided Barrier 6V AC/DC±5% AP6GS5➁ LSTD-6➁ Solder/Tab Terminal 1V AC/DC±10% AP6GS53➁ LSTD-1➁ 4V AC/DC±10% AP6GS54➁ LSTD-➁ 6V AC/DC±5% AP6GS5M➁ LSTD-6➁ Screw Terminal 1V AC/DC±10% AP6GS53M➁ LSTD-1➁ 4V AC/DC±10% AP6GS54M➁ LSTD-➁ (07/03/26) 11 +0.2 ø16.2 0 ø16 AP6S Series Miniature Pilot Lights Dimensions • Screw Terminal Panel Thickness 0.8 to 4 19 Hex Nut 18 24 24 Gasket (TOP) (TOP) (TOP) (TOP) 6 0.6 9 22 Rectangular Rectangular Round Square 9 39.5 (3-sided Barrier) Hex Nut M2.6 Terminal Screw M2.6 Terminal Screw 5.7 37 2.5 • Solder/Tab Screw Terminal Panel Thickness 0.8 to 6 18 24 24 3.8 Gasket ( ) ( ) ( ) ( ) TOP TOP TOP TOP X1 X2 6 0.6 8.8 9 22 Round Square Rectangular Rectangular 23 (3-sided Barrier) 9 31 Locking Ring (plastic) 5.7 #110 Solder/Tab Terminal Width 2.8×0.5t All dimensions in mm. Mounting Hole Layout • Minimum Mounting Centers A B Round/Square Rectangular Round/Square Rectangular Screw Terminal 3 mm 3 mm 3 mm 4 mm B Tab Terminal 18 mm 18 mm 18 mm 4 mm Terminal Arrangement (Bottom View) • Screw Terminal • Solder/Tab Terminal TOP TOP X1 Lamp Terminal (X1) Lamp Terminal (X1) X2 X2 Lamp Terminal (X2) Lamp Terminal (X2) 1 (07/03/26) A 21.9 ø17.8 ø17.8 ø15.4 ø15.4 18 18 18 18 18 18 8.2 10 ø16 AP6S Series Miniature Pilot Lights Accessories • Tools Ordering Package Shape Specification Type No. Remarks Type No. Quantity Locking Ring Wrench ø18 Used to tighten the locking ring Metal MT-001 MT-001 1 when installing an AP6S unit onto a (nickel-plated brass) panel. 60 Lamp Holder Tool ø11.6 Used to install and remove LED Rubber OR-55 OR-55 1 lamps. ø14 59 Lens Removal Tool Stainless Steel MT-101 MT-101 1 Used to remove lens and buttons. 60 • Replacement Parts for AP6M/AP2M/AP1M Ordering Package Shape Type No. Remarks Type No. Quantity Lens Specify a color code in place of ➁ in Round AL6M-L➁ AL6M-L➁PN05 5 the Ordering Type No. A: amber C: clear Square AL6Q-L➁ AL6Q-L➁PN05 5 G: green R: red S: blue Rectangular Y: yellow Rectangular with AL6H-L➁ AL6H-L➁PN05 5 Use a clear lens for white illumination. 3-sided Barrier Marking Plate Round AL6M-W AL6M-WPN05 5 Square AL6Q-W AL6Q-WPN05 5 White Rectangular Rectangular with AL6H-W AL6H-WPN05 5 3-sided Barrier • LED Lamps Current Draw Ordering Package Operating Voltage Type No. ➁Illumination Color Code Base Type No. Quantity AC DC 7 mA LSTD-6➁ 1 Specify a color code in (A, R, W) 6V DC ±10% 8 mA LSTD-6➁ place of ➁ in the Ordering 5.5 mA LSTD-6➁PN10 Type No. 10 (G, PW, S) A: amber LSTD-1➁ 1 G: green 1V AC/DC ±10% 11 mA 10 mA LSTD-1➁ PW: pure white BA9S/13 R: red LSTD-1➁PN10 10 S: blue W: white LSTD-➁ 1 Use a pure white (PW) LED 4V AC/DC ±10% 11 mA 10 mA LSTD-➁ lamp with yellow (Y) lens. LSTD-➁PN10 10 13 (07/03/26) ø16 AP6S Series Miniature Pilot Lights Safety Precautions • Turn off power to the AP6S series units before installation, re- • For wiring, use wires of proper size to meet the voltage and cur- moval, wiring, maintenance, and inspection. Failure to turn power rent requirements. Improper soldering may cause overheating and off may cause electrical shocks or fire hazard. create fire hazards. Instructions • Tab Terminal Replacing Lens and Marking Plate The locking ring is plastic. To tighten the ring, use an optional • Removal locking ring wrench (MT-001). Do not use pliers. Do not tighten Remove the operator (color lens, marking plate, and lens holder) with excessive force, otherwise the locking ring will be damaged. by holding the color lens recesses with the Lens Removal Tool Tightening torque should not exceed 0.88 N·m (MT-101) and pulling it out. Remove the marking plate by • Collective Mounting and Continous Illumination disengaging the latches between the color lens and lens holder. Collective mounting or continuous illumination of pilot lights may The marking plate must be engraved on the front side as shown cause the ambient temperature to rise above the rated operating below. temperature. Make sure to provide efficient ventilation when the mounting panel is not metallic or when the pilot lights are mounted Waterproof Gasket Fitting Grooves collectively. (silicon rubber) Grooves Wiring Solder the terminal at 350°C within 3 seconds using a 60W soldering iron. SnAgCu type lead-free solder is recommended. Engrraving When soldering, do not touch the pilot light housing with the Surface soldering iron. Also ensure that no tensile force is applied to the terminal. Do not bend the terminal or apply excessive force to the Color Lens Marking Plate Lens Holder terminal. (polyarylate) (acryl) (polyarylate) Power Supply for LED Lamps The operating voltage of the LED lamp is within ±5% or ±10% of • Installation the rated voltage. Make sure that the power voltage is within this range. Place the marking plate on the lens holder in the correct direction and press the color lens onto the lens holder to engage the latches. Insert the lens holder into the housing in the correct direction. Marking Plate and Engraving Area Engraving must be made on the engraving area less than 0.5mm deep. Shape Size Engraving Area Round ø13.8 mm ø1 mm Square 13.8 mm 1 mm Rectangular 13.8×19.8 mm 1×18 mm Notes on Mounting • Screw Terminal • Because screw terminal types use hexagonal nuts, they cannot be mounted closely together. However, rectangular units can be mounted closely when installed horizontally. • When removing the hexagonal nuts, loosen the the terminal screws. The hexagonal nuts cannot be removed when the termi- nal screws are tightened. • When mounting the pilot lights collectively, note the mounting order. Pilot lights mounted in between units cannot be removed. 14 (07/03/26) 45 ø16 AP6S Series Miniature Pilot Lights Transformer Separate Mounting Type Primary Voltage Secondary Voltage Type No. (Ordering Type No.) Applicable LED Lamp For 4V 100/110V AC 4V AC, 0.5W TWR51 00/0V AC 4V AC, 0.5W TWR5 LSTD-➁ 400/440V AC 4V AC, 0.5W TWR54 • A dust cover is supplied with the separate mounting type transformer. • Connect only one LSTD LED lamp to the separate mounting type transformer. • Use plastic mounting clip BC9Z-E/NS35N when mounting 400/440V voltage models. Dimensions Specifications 100/110V AC, 00/0V AC M3.5 Terminal Screw Operating Voltage 400/440V AC (50/60 Hz) Power Consumption .4 VA Rated Insulation Voltage 600V Secondary Side Primary Side Insulation Resistance 100 MΩ minimum (500V DC megger) Operating Temperature –30 to +60°C (no freezing) 40 Relative Humidity 35 to 85% (no condensation) Mounting Hole 48 Vibration Resistance Operating extremes: 5 to 55 Hz, amplitude 0.5 mm 2–ø3.3  52 Shock Resistance Damage limits: 1,000 m/s Dielectric Strength ,500V AC, 1 minute Terminal Style M3.5  Applicable Wire  mm maximum, 2 wires maximum Terminal Screw Accessories Description Appearance Description Type No. Ordering Type No. Package Quantity Aluminum Weight: Approx. 200g BAA1000 BAA1000PN10 Length: 1m DIN Rail Steel Weight: Approx. 320g BAP1000 BAP1000PN10 Length: 1m 10 Steel BNL6 BNL6PN10 Weight: Approx.15g Mounting Clip 9.5 48.6 Plastic BC9Z-E/NS35N BC9Z-E/NS35NPN10 Weight: Approx.15g • Use plastic mounting clip BC9Z/NS35N when using 400/440V AC voltage transformers. 15 (07/03/26) 9 3.8 40 22 41 30