New 12V DC MicroSmart Pentra 12V DC CPU Module Model Features Applications • 3 CPUs to choose from • Solar industry -solar traffic control & lighting -10 I/O, 16 I/O, 24 I/O -remote solar pumping stations (oil & gas • Fast processing speed industry) • Built-in Modbus RTU, ASCII and TCP/IP -remote solar injection systems (oil & gas • Support 32-bit and floating point math industry) • Four built-in high speed inputs -solar water pumping stations -1pt: 50kHz single/dual phase -solar trackers -3pts: 5kHz single phase • Vehicle/automotive • Field upgradeable firmware -handicap lifts, garbage trucks, bus/train lighting & signage, cement truck mixers Specifications Function Specifications General Specifications Part Number FC5A-C10R2D FC5A-C16R2D FC5A-C24R2D Part Number FC5A-C10R2D FC5A-C16R2D FC5A-C24R2D Rated Power Voltage 12V DC Control System Stored program system Allowable Voltage 42 basic 10.2 to 18.0V DC Instruction Words Range 103 advanced 130 advanced 115 advanced Maximum 4.2W 28W 3.4W *1 Power Consumption Program Capacity 13.8 KB (2,300 steps) 27 KB (4,500 steps) 54 KB (9,000 steps) Allowable Momentary 10 ms (at rated power voltage) User Program Storage EEPROM (10,000 times rewritable) Power Interruption Basic Instruction 1.16 ms (1,000 steps) Processing Between power and terminals: *2 Time END Processing 0.64 ms 1,500V AC, 1 minute Dielectric Strength Between I/O and terminals: Input 6 9 14 Max. I/O 1,500V AC, 1 minute *3 Points Output 4 7 10 Between power and terminals: Internal Relay 2,048 points 10 MΩ minimum (500V DC megger) Insulation Resistance Between I/O and terminals: Shift Register 128 points 10 MΩ minimum (500V DC megger) Timer 256 points (1-sec, 100-ms, 10-ms, 1-ms) DC power terminals: 1.0 kV, 50 ns to 1 µs Noise Resistance Counter 256 points (adding, reversible) I/O terminals (coupling clamp): 1.5 kV, 50 ns to 1 µs Data Register 2,000 points Inrush Current 20A maximum Backup Data Internal relay, shift register, counter, data register Power Supply Wire UL1015 AWG22, UL1007 AWG18 Backup Duration Approx. 30 days (typical) at 25ºC after backup battery fully charged Operating Temperature 0 to +55ºC Battery Lithium secondary battery Storage Temperature –25 to +70ºC (no freezing) Charging Time Approx. 15 hours for charging from 0% to 90% of full charge Relative Humidity 10 to 95% (no condensation) Battery Life 5 years in cycles of 9-hour charging and 15-hour discharging Altitude Operation: 0 to 2,000m, Transport: 0 to 3,000m Replaceability Not possible to replace battery Keep data check, user program EPPROM sum check, user program Pollution Degree 2 (IEC60664-1) Self-diagnostic RAM sum check, timer/counter preset value sum check, user program Corrosion Immunity Free from corrosive gases Function syntax, WDT check, user program writing, power failure, watchdog Grounding Wire UL1007 AWG16 timer, data link connection When mounted on a DIN rail or panel surface: Input Filter Without filter, 3 to 15 ms (selectable in increments of 1 ms) 2 5 to 9 Hz amplitude 3.5 mm, 9 to 150 Hz acceleration 9.8 m/s Four inputs (I2 through I5) Vibration Resistance Catch Input/ (1G), 2 hours per axis on each of three mutually perpendicular Minimum turn on pulse width: 40 µs maximum Interrupt Input axes (IEC61131-2) Minimum turn off pulse width: 150 µs maximum 2 Maximum Counting Total 4 points 147 m/s (15G), 11 ms duration, 3 shocks per axis on three Shock Resistance Frequency and High- Single/two-phase selectable: 50 kHz (1 point) mutually perpendicular axes (IEC61131-2) speed Counter Points Single-phase: 5 kHz (3 points) 310g Weight 240g 260g Counting Range 0 to 65535 (16 bits) Operation Mode Rotary encoder mode, adding counter mode Communication Port (RS232C, port1) Analog Quantity 1 point 2 points Standards EIA RS232C Potentiometer Data Range 0 to 255 RS232C – maintenance communication, user communication, Maximum Baud Rate 57600 bps (maintenance communication) Port 1 Modbus slave communication Maintenance Communication Possible Port 2 Communication Possible Possible Possible *4 User Communication Possible Adapter (option) Clock Cartridge (option) Possible Possible Possible Data Link Communication Impossible Memory Cartridge (option) Possible Possible Possible Cable FC2A-KC4C, FC2A-KP1C, FC4A-KC2CA HMI Module (option) Possible Possible Possible Isolation between Internal Circuit and Not isolated Communication Port *1. 1 step equals 6 bytes. *3. Not expandable with expansion I/O modules. *2. Not including clock function processing time, data *4. Maintenance communication, user communication, Notes: link processing time, and interrupt processing time. modem communication, data link, Modbus master/ slave communication 1. Port 1 is modbus slave. 2. Port 2 is modbus master/slave. 3. 12V DC CPUs are not expandable. High-speed RAM Backup Counter Specifications con’t Installation When the CPU module is mounted in the standard upright position, all I/O Input Specifications points can be turned on simultaneously at up to 55ºC operating temperature. Part Number FC5A-C10R2D FC5A-C16R2D FC5A-C24R2D Input Points 6 (6/1 common) 9 (9/1 common) 14 (14/1 common) The CPU module can be installed facing upwards when the operating tempera- Rated Input Voltage 12V DC sink/source input signal ture is below 35ºC or sideways when the operating temperature is below 40ºC. Input Voltage Range 10.2 to 18V DC Mounting CPU Facing Up Mounting CPU Sideways I0 and I1: 6 mA Rated Input Current Operating temperature below 35ºC Operating temperature below 40ºC I2 to I7, I10 to I15: 6 mA I0 and I1: 1.8 kΩ Input Impedance I2 to I7, I10 to I15: 2.0 kΩ I0 and I1: 2 µs + filter value Turn ON Time I2 to I5: 35 µs + filter value I6, I7, I10 to I15: 40 µs + filter value I0 and I1: 16 µs + filter value Turn OFF Time I2 to I5: 150 µs + filter value I6, I7, I10 to I15: 150 µs + filter value Between input terminals: Not isolated Isolation Internal circuit: Photocoupler isolated Dimensions Input Type Type 1 (IEC61131-2) FC5A-C10R2D, FC5A-C16R2D External Load for I/O Not needed 80.0 70.0 Interconnection Single Determination Method Static Both sinking and sourcing input signals can be connected. Effect of Improper Input If any input exceeding the rated value is applied, Connection permanent damage may be caused. Cable Length 3m in compliance with electromagnetic immunity Relay Output Specifications Part Number FC5A-C10R2D FC5A-C16R2D FC5A-C24R2D No. of Outputs 4 7 10 COM0 3 4 4 ∗8.5 mm when the clamp is pulled out. COM1 1 2 4 Output Points per FC5A-C24R2D Common Line COM2 — 1 1 95.0 70.0 COM3 — — 1 Output Type 1NO 2A per point Maximum Load Current 8A per common line Minimum Switching Load 0.1 mA/0.1V DC (reference value) Initial Contact Resistance 30 mΩ maximum 100,000 operations minimum Electrical Life (rated load 1,800 operations/hour) 20,000,000 operations minimum Mechanical Life (no load 18,000 operations/hour) ∗8.5 mm when the clamp is pulled out. 240V AC/2A (resistive load, inductive load cos ø = 0.4) Rated Load 30V DC/2A (resistive load, inductive load L/R =7 ms) Between output and terminals: 1,500V AC, 1 minute Between output terminal and internal circuit: Dielectric Strength Mounting Hole Layout 1,500V AC, 1 minute Between output terminals (COMs): FC5A-C10R2D, FC5A-C16R2D FC5A-C24R2D 1,500V AC, 1 minute 80.0 95.0 Input Internal Circuit 1.8 kΩ Input X0, X1 COM 68.0 83.0 2.0 kΩ Input All dimensions in mm. X2 to X15 COM IDEC Corporation • 1175 Elko Drive • Sunnyvale, CA 94089 • 800-262-IDEC (4332) • Fax: 408-745-5258 • www.IDEC.com/usa ©2008 IDEC Corporation. All Rights Reserved. FC9Y-DS200-0 15K 07/08 2-ø4.3 2-ø4.3 Internal Circuit Internal Circuit 90.0 83.0 90.0 4.5∗ 4.5∗ 90.0 90.0 83.0